xref: /rk3399_ARM-atf/plat/brcm/board/stingray/platform.mk (revision f29d1e0c72e6665ba4c8ab11bad83f59669ea0d9)

#
# Copyright (c) 2019-2020, Broadcom
#
# SPDX-License-Identifier: BSD-3-Clause
#

# Set the toc_flags to 1 for 100% speed operation
# Set the toc_flags to 2 for 50% speed operation
# Set the toc_flags to 3 for 25% speed operation
# Set the toc_flags bit 3 to indicate ignore the fip in UEFI copy mode
PLAT_TOC_FLAGS := 0x0

# Set the IHOST_PLL_FREQ to,
# 1 for full speed
# 2 for 50% speed
# 3 for 25% speed
# 0 for bypass
$(eval $(call add_define_val,IHOST_PLL_FREQ,1))

# Enable workaround for ERRATA_A72_859971
ERRATA_A72_859971 := 1

# Cache Coherency Interconnect Driver needed
DRIVER_CC_ENABLE := 1
$(eval $(call add_define,DRIVER_CC_ENABLE))

# BL31 is in DRAM
ARM_BL31_IN_DRAM	:=	1

USE_CRMU_SRAM := yes

# Enable error logging by default for Stingray
BCM_ELOG := yes

# Enable FRU support by default for Stingray
ifeq (${USE_FRU},)
USE_FRU := no
endif

# Use single cluster
ifeq (${USE_SINGLE_CLUSTER},yes)
$(info Using Single Cluster)
$(eval $(call add_define,USE_SINGLE_CLUSTER))
endif

# Use DDR
ifeq (${USE_DDR},yes)
$(info Using DDR)
$(eval $(call add_define,USE_DDR))
endif

ifeq (${BOARD_CFG},)
BOARD_CFG := bcm958742k
endif

# Use NAND
ifeq (${USE_NAND},$(filter yes, ${USE_NAND}))
$(info Using NAND)
$(eval $(call add_define,USE_NAND))
endif

# Enable Broadcom error logging support
ifeq (${BCM_ELOG},yes)
$(info Using BCM_ELOG)
$(eval $(call add_define,BCM_ELOG))
endif

# BL31 build for standalone mode
ifeq (${STANDALONE_BL31},yes)
RESET_TO_BL31 := 1
$(info Using RESET_TO_BL31)
endif

# For testing purposes, use memsys stubs.  Remove once memsys is fully tested.
USE_MEMSYS_STUBS := yes

# Default, use BL1_RW area
ifneq (${BL2_USE_BL1_RW},no)
$(eval $(call add_define,USE_BL1_RW))
endif

# Default soft reset is L3
$(eval $(call add_define,CONFIG_SOFT_RESET_L3))

# Enable Chip OTP driver
DRIVER_OCOTP_ENABLE := 1

include plat/brcm/board/common/board_common.mk

SOC_DIR			:= 	brcm/board/stingray

PLAT_INCLUDES		+=	-Iplat/${SOC_DIR}/include/ \
				-Iinclude/plat/brcm/common/ \
				-Iplat/brcm/common/

PLAT_BL_COMMON_SOURCES	+=	lib/cpus/aarch64/cortex_a72.S \
				plat/${SOC_DIR}/aarch64/plat_helpers.S \
				drivers/ti/uart/aarch64/16550_console.S \
				plat/${SOC_DIR}/src/tz_sec.c \
				drivers/arm/tzc/tzc400.c \
				plat/${SOC_DIR}/src/topology.c

BL2_SOURCES		+=	plat/${SOC_DIR}/driver/ihost_pll_config.c \
				plat/${SOC_DIR}/src/bl2_setup.c \
				plat/${SOC_DIR}/driver/swreg.c


ifeq (${USE_DDR},yes)
PLAT_INCLUDES		+=	-Iplat/${SOC_DIR}/driver/ddr/soc/include
else
PLAT_INCLUDES		+=	-Iplat/${SOC_DIR}/driver/ext_sram_init
BL2_SOURCES		+=	plat/${SOC_DIR}/driver/ext_sram_init/ext_sram_init.c
endif

# Include GICv3 driver files
include drivers/arm/gic/v3/gicv3.mk

BRCM_GIC_SOURCES	:=	${GICV3_SOURCES}		\
				plat/common/plat_gicv3.c	\
				plat/brcm/common/brcm_gicv3.c

BL31_SOURCES		+=	\
				drivers/arm/ccn/ccn.c \
				plat/brcm/board/common/timer_sync.c \
				plat/brcm/common/brcm_ccn.c \
				plat/common/plat_psci_common.c \
				plat/${SOC_DIR}/driver/ihost_pll_config.c \
				${BRCM_GIC_SOURCES}

ifdef SCP_BL2
PLAT_INCLUDES		+=	-Iplat/brcm/common/

BL2_SOURCES		+=	plat/brcm/common/brcm_mhu.c \
				plat/brcm/common/brcm_scpi.c \
				plat/${SOC_DIR}/src/scp_utils.c \
				plat/${SOC_DIR}/src/scp_cmd.c \
				drivers/brcm/scp.c

BL31_SOURCES		+=	plat/brcm/common/brcm_mhu.c \
				plat/brcm/common/brcm_scpi.c \
				plat/${SOC_DIR}/src/brcm_pm_ops.c
else
BL31_SOURCES		+=	plat/${SOC_DIR}/src/ihost_pm.c \
				plat/${SOC_DIR}/src/pm.c
endif

ifeq (${ELOG_SUPPORT},1)
ifeq (${ELOG_STORE_MEDIA},DDR)
BL2_SOURCES		+=	plat/brcm/board/common/bcm_elog_ddr.c
endif
endif

# Do not execute the startup code on warm reset.
PROGRAMMABLE_RESET_ADDRESS	:=	1

# Nitro FW, config and Crash log uses secure DDR memory
# Inaddition to above, Nitro master and slave is also secure
ifneq ($(NITRO_SECURE_ACCESS),)
$(eval $(call add_define,NITRO_SECURE_ACCESS))
$(eval $(call add_define,DDR_NITRO_SECURE_REGION_START))
$(eval $(call add_define,DDR_NITRO_SECURE_REGION_END))
endif