1Build Options 2============= 3 4The TF-A build system supports the following build options. Unless mentioned 5otherwise, these options are expected to be specified at the build command 6line and are not to be modified in any component makefiles. Note that the 7build system doesn't track dependency for build options. Therefore, if any of 8the build options are changed from a previous build, a clean build must be 9performed. 10 11.. _build_options_common: 12 13Common build options 14-------------------- 15 16- ``AARCH32_INSTRUCTION_SET``: Choose the AArch32 instruction set that the 17 compiler should use. Valid values are T32 and A32. It defaults to T32 due to 18 code having a smaller resulting size. 19 20- ``AARCH32_SP`` : Choose the AArch32 Secure Payload component to be built as 21 as the BL32 image when ``ARCH=aarch32``. The value should be the path to the 22 directory containing the SP source, relative to the ``bl32/``; the directory 23 is expected to contain a makefile called ``<aarch32_sp-value>.mk``. 24 25- ``ARCH`` : Choose the target build architecture for TF-A. It can take either 26 ``aarch64`` or ``aarch32`` as values. By default, it is defined to 27 ``aarch64``. 28 29- ``ARM_ARCH_MAJOR``: The major version of Arm Architecture to target when 30 compiling TF-A. Its value must be numeric, and defaults to 8 . See also, 31 *Armv8 Architecture Extensions* and *Armv7 Architecture Extensions* in 32 :ref:`Firmware Design`. 33 34- ``ARM_ARCH_MINOR``: The minor version of Arm Architecture to target when 35 compiling TF-A. Its value must be a numeric, and defaults to 0. See also, 36 *Armv8 Architecture Extensions* in :ref:`Firmware Design`. 37 38- ``BL2``: This is an optional build option which specifies the path to BL2 39 image for the ``fip`` target. In this case, the BL2 in the TF-A will not be 40 built. 41 42- ``BL2U``: This is an optional build option which specifies the path to 43 BL2U image. In this case, the BL2U in TF-A will not be built. 44 45- ``BL2_AT_EL3``: This is an optional build option that enables the use of 46 BL2 at EL3 execution level. 47 48- ``BL2_IN_XIP_MEM``: In some use-cases BL2 will be stored in eXecute In Place 49 (XIP) memory, like BL1. In these use-cases, it is necessary to initialize 50 the RW sections in RAM, while leaving the RO sections in place. This option 51 enable this use-case. For now, this option is only supported when BL2_AT_EL3 52 is set to '1'. 53 54- ``BL31``: This is an optional build option which specifies the path to 55 BL31 image for the ``fip`` target. In this case, the BL31 in TF-A will not 56 be built. 57 58- ``BL31_KEY``: This option is used when ``GENERATE_COT=1``. It specifies the 59 file that contains the BL31 private key in PEM format. If ``SAVE_KEYS=1``, 60 this file name will be used to save the key. 61 62- ``BL32``: This is an optional build option which specifies the path to 63 BL32 image for the ``fip`` target. In this case, the BL32 in TF-A will not 64 be built. 65 66- ``BL32_EXTRA1``: This is an optional build option which specifies the path to 67 Trusted OS Extra1 image for the ``fip`` target. 68 69- ``BL32_EXTRA2``: This is an optional build option which specifies the path to 70 Trusted OS Extra2 image for the ``fip`` target. 71 72- ``BL32_KEY``: This option is used when ``GENERATE_COT=1``. It specifies the 73 file that contains the BL32 private key in PEM format. If ``SAVE_KEYS=1``, 74 this file name will be used to save the key. 75 76- ``BL33``: Path to BL33 image in the host file system. This is mandatory for 77 ``fip`` target in case TF-A BL2 is used. 78 79- ``BL33_KEY``: This option is used when ``GENERATE_COT=1``. It specifies the 80 file that contains the BL33 private key in PEM format. If ``SAVE_KEYS=1``, 81 this file name will be used to save the key. 82 83- ``BRANCH_PROTECTION``: Numeric value to enable ARMv8.3 Pointer Authentication 84 and ARMv8.5 Branch Target Identification support for TF-A BL images themselves. 85 If enabled, it is needed to use a compiler that supports the option 86 ``-mbranch-protection``. Selects the branch protection features to use: 87- 0: Default value turns off all types of branch protection 88- 1: Enables all types of branch protection features 89- 2: Return address signing to its standard level 90- 3: Extend the signing to include leaf functions 91 92 The table below summarizes ``BRANCH_PROTECTION`` values, GCC compilation options 93 and resulting PAuth/BTI features. 94 95 +-------+--------------+-------+-----+ 96 | Value | GCC option | PAuth | BTI | 97 +=======+==============+=======+=====+ 98 | 0 | none | N | N | 99 +-------+--------------+-------+-----+ 100 | 1 | standard | Y | Y | 101 +-------+--------------+-------+-----+ 102 | 2 | pac-ret | Y | N | 103 +-------+--------------+-------+-----+ 104 | 3 | pac-ret+leaf | Y | N | 105 +-------+--------------+-------+-----+ 106 107 This option defaults to 0 and this is an experimental feature. 108 Note that Pointer Authentication is enabled for Non-secure world 109 irrespective of the value of this option if the CPU supports it. 110 111- ``BUILD_MESSAGE_TIMESTAMP``: String used to identify the time and date of the 112 compilation of each build. It must be set to a C string (including quotes 113 where applicable). Defaults to a string that contains the time and date of 114 the compilation. 115 116- ``BUILD_STRING``: Input string for VERSION_STRING, which allows the TF-A 117 build to be uniquely identified. Defaults to the current git commit id. 118 119- ``CFLAGS``: Extra user options appended on the compiler's command line in 120 addition to the options set by the build system. 121 122- ``COLD_BOOT_SINGLE_CPU``: This option indicates whether the platform may 123 release several CPUs out of reset. It can take either 0 (several CPUs may be 124 brought up) or 1 (only one CPU will ever be brought up during cold reset). 125 Default is 0. If the platform always brings up a single CPU, there is no 126 need to distinguish between primary and secondary CPUs and the boot path can 127 be optimised. The ``plat_is_my_cpu_primary()`` and 128 ``plat_secondary_cold_boot_setup()`` platform porting interfaces do not need 129 to be implemented in this case. 130 131- ``CRASH_REPORTING``: A non-zero value enables a console dump of processor 132 register state when an unexpected exception occurs during execution of 133 BL31. This option defaults to the value of ``DEBUG`` - i.e. by default 134 this is only enabled for a debug build of the firmware. 135 136- ``CREATE_KEYS``: This option is used when ``GENERATE_COT=1``. It tells the 137 certificate generation tool to create new keys in case no valid keys are 138 present or specified. Allowed options are '0' or '1'. Default is '1'. 139 140- ``CTX_INCLUDE_AARCH32_REGS`` : Boolean option that, when set to 1, will cause 141 the AArch32 system registers to be included when saving and restoring the 142 CPU context. The option must be set to 0 for AArch64-only platforms (that 143 is on hardware that does not implement AArch32, or at least not at EL1 and 144 higher ELs). Default value is 1. 145 146- ``CTX_INCLUDE_FPREGS``: Boolean option that, when set to 1, will cause the FP 147 registers to be included when saving and restoring the CPU context. Default 148 is 0. 149 150- ``CTX_INCLUDE_PAUTH_REGS``: Boolean option that, when set to 1, enables 151 Pointer Authentication for Secure world. This will cause the ARMv8.3-PAuth 152 registers to be included when saving and restoring the CPU context as 153 part of world switch. Default value is 0 and this is an experimental feature. 154 Note that Pointer Authentication is enabled for Non-secure world irrespective 155 of the value of this flag if the CPU supports it. 156 157- ``DEBUG``: Chooses between a debug and release build. It can take either 0 158 (release) or 1 (debug) as values. 0 is the default. 159 160- ``DISABLE_BIN_GENERATION``: Boolean option to disable the generation 161 of the binary image. If set to 1, then only the ELF image is built. 162 0 is the default. 163 164- ``DYN_DISABLE_AUTH``: Provides the capability to dynamically disable Trusted 165 Board Boot authentication at runtime. This option is meant to be enabled only 166 for development platforms. ``TRUSTED_BOARD_BOOT`` flag must be set if this 167 flag has to be enabled. 0 is the default. 168 169- ``E``: Boolean option to make warnings into errors. Default is 1. 170 171- ``EL3_PAYLOAD_BASE``: This option enables booting an EL3 payload instead of 172 the normal boot flow. It must specify the entry point address of the EL3 173 payload. Please refer to the "Booting an EL3 payload" section for more 174 details. 175 176- ``ENABLE_AMU``: Boolean option to enable Activity Monitor Unit extensions. 177 This is an optional architectural feature available on v8.4 onwards. Some 178 v8.2 implementations also implement an AMU and this option can be used to 179 enable this feature on those systems as well. Default is 0. 180 181- ``ENABLE_ASSERTIONS``: This option controls whether or not calls to ``assert()`` 182 are compiled out. For debug builds, this option defaults to 1, and calls to 183 ``assert()`` are left in place. For release builds, this option defaults to 0 184 and calls to ``assert()`` function are compiled out. This option can be set 185 independently of ``DEBUG``. It can also be used to hide any auxiliary code 186 that is only required for the assertion and does not fit in the assertion 187 itself. 188 189- ``ENABLE_BACKTRACE``: This option controls whether to enables backtrace 190 dumps or not. It is supported in both AArch64 and AArch32. However, in 191 AArch32 the format of the frame records are not defined in the AAPCS and they 192 are defined by the implementation. This implementation of backtrace only 193 supports the format used by GCC when T32 interworking is disabled. For this 194 reason enabling this option in AArch32 will force the compiler to only 195 generate A32 code. This option is enabled by default only in AArch64 debug 196 builds, but this behaviour can be overridden in each platform's Makefile or 197 in the build command line. 198 199- ``ENABLE_LTO``: Boolean option to enable Link Time Optimization (LTO) 200 support in GCC for TF-A. This option is currently only supported for 201 AArch64. Default is 0. 202 203- ``ENABLE_MPAM_FOR_LOWER_ELS``: Boolean option to enable lower ELs to use MPAM 204 feature. MPAM is an optional Armv8.4 extension that enables various memory 205 system components and resources to define partitions; software running at 206 various ELs can assign themselves to desired partition to control their 207 performance aspects. 208 209 When this option is set to ``1``, EL3 allows lower ELs to access their own 210 MPAM registers without trapping into EL3. This option doesn't make use of 211 partitioning in EL3, however. Platform initialisation code should configure 212 and use partitions in EL3 as required. This option defaults to ``0``. 213 214- ``ENABLE_PIE``: Boolean option to enable Position Independent Executable(PIE) 215 support within generic code in TF-A. This option is currently only supported 216 in BL31. Default is 0. 217 218- ``ENABLE_PMF``: Boolean option to enable support for optional Performance 219 Measurement Framework(PMF). Default is 0. 220 221- ``ENABLE_PSCI_STAT``: Boolean option to enable support for optional PSCI 222 functions ``PSCI_STAT_RESIDENCY`` and ``PSCI_STAT_COUNT``. Default is 0. 223 In the absence of an alternate stat collection backend, ``ENABLE_PMF`` must 224 be enabled. If ``ENABLE_PMF`` is set, the residency statistics are tracked in 225 software. 226 227- ``ENABLE_RUNTIME_INSTRUMENTATION``: Boolean option to enable runtime 228 instrumentation which injects timestamp collection points into TF-A to 229 allow runtime performance to be measured. Currently, only PSCI is 230 instrumented. Enabling this option enables the ``ENABLE_PMF`` build option 231 as well. Default is 0. 232 233- ``ENABLE_SPE_FOR_LOWER_ELS`` : Boolean option to enable Statistical Profiling 234 extensions. This is an optional architectural feature for AArch64. 235 The default is 1 but is automatically disabled when the target architecture 236 is AArch32. 237 238- ``ENABLE_SPM`` : Boolean option to enable the SPCI-based Secure Partition 239 Manager (SPM) implementation. 240 Refer to the :ref:`Secure Partition Manager` guide for more details about 241 this feature. Default is 0. 242 243- ``ENABLE_SVE_FOR_NS``: Boolean option to enable Scalable Vector Extension 244 (SVE) for the Non-secure world only. SVE is an optional architectural feature 245 for AArch64. Note that when SVE is enabled for the Non-secure world, access 246 to SIMD and floating-point functionality from the Secure world is disabled. 247 This is to avoid corruption of the Non-secure world data in the Z-registers 248 which are aliased by the SIMD and FP registers. The build option is not 249 compatible with the ``CTX_INCLUDE_FPREGS`` build option, and will raise an 250 assert on platforms where SVE is implemented and ``ENABLE_SVE_FOR_NS`` set to 251 1. The default is 1 but is automatically disabled when the target 252 architecture is AArch32. 253 254- ``ENABLE_STACK_PROTECTOR``: String option to enable the stack protection 255 checks in GCC. Allowed values are "all", "strong", "default" and "none". The 256 default value is set to "none". "strong" is the recommended stack protection 257 level if this feature is desired. "none" disables the stack protection. For 258 all values other than "none", the ``plat_get_stack_protector_canary()`` 259 platform hook needs to be implemented. The value is passed as the last 260 component of the option ``-fstack-protector-$ENABLE_STACK_PROTECTOR``. 261 262- ``ERROR_DEPRECATED``: This option decides whether to treat the usage of 263 deprecated platform APIs, helper functions or drivers within Trusted 264 Firmware as error. It can take the value 1 (flag the use of deprecated 265 APIs as error) or 0. The default is 0. 266 267- ``EL3_EXCEPTION_HANDLING``: When set to ``1``, enable handling of exceptions 268 targeted at EL3. When set ``0`` (default), no exceptions are expected or 269 handled at EL3, and a panic will result. This is supported only for AArch64 270 builds. 271 272- ``FAULT_INJECTION_SUPPORT``: ARMv8.4 extensions introduced support for fault 273 injection from lower ELs, and this build option enables lower ELs to use 274 Error Records accessed via System Registers to inject faults. This is 275 applicable only to AArch64 builds. 276 277 This feature is intended for testing purposes only, and is advisable to keep 278 disabled for production images. 279 280- ``FIP_NAME``: This is an optional build option which specifies the FIP 281 filename for the ``fip`` target. Default is ``fip.bin``. 282 283- ``FWU_FIP_NAME``: This is an optional build option which specifies the FWU 284 FIP filename for the ``fwu_fip`` target. Default is ``fwu_fip.bin``. 285 286- ``GENERATE_COT``: Boolean flag used to build and execute the ``cert_create`` 287 tool to create certificates as per the Chain of Trust described in 288 :ref:`Trusted Board Boot`. The build system then calls ``fiptool`` to 289 include the certificates in the FIP and FWU_FIP. Default value is '0'. 290 291 Specify both ``TRUSTED_BOARD_BOOT=1`` and ``GENERATE_COT=1`` to include support 292 for the Trusted Board Boot feature in the BL1 and BL2 images, to generate 293 the corresponding certificates, and to include those certificates in the 294 FIP and FWU_FIP. 295 296 Note that if ``TRUSTED_BOARD_BOOT=0`` and ``GENERATE_COT=1``, the BL1 and BL2 297 images will not include support for Trusted Board Boot. The FIP will still 298 include the corresponding certificates. This FIP can be used to verify the 299 Chain of Trust on the host machine through other mechanisms. 300 301 Note that if ``TRUSTED_BOARD_BOOT=1`` and ``GENERATE_COT=0``, the BL1 and BL2 302 images will include support for Trusted Board Boot, but the FIP and FWU_FIP 303 will not include the corresponding certificates, causing a boot failure. 304 305- ``GICV2_G0_FOR_EL3``: Unlike GICv3, the GICv2 architecture doesn't have 306 inherent support for specific EL3 type interrupts. Setting this build option 307 to ``1`` assumes GICv2 *Group 0* interrupts are expected to target EL3, both 308 by `platform abstraction layer`__ and `Interrupt Management Framework`__. 309 This allows GICv2 platforms to enable features requiring EL3 interrupt type. 310 This also means that all GICv2 Group 0 interrupts are delivered to EL3, and 311 the Secure Payload interrupts needs to be synchronously handed over to Secure 312 EL1 for handling. The default value of this option is ``0``, which means the 313 Group 0 interrupts are assumed to be handled by Secure EL1. 314 315 .. __: `platform-interrupt-controller-API.rst` 316 .. __: `interrupt-framework-design.rst` 317 318- ``HANDLE_EA_EL3_FIRST``: When set to ``1``, External Aborts and SError 319 Interrupts will be always trapped in EL3 i.e. in BL31 at runtime. When set to 320 ``0`` (default), these exceptions will be trapped in the current exception 321 level (or in EL1 if the current exception level is EL0). 322 323- ``HW_ASSISTED_COHERENCY``: On most Arm systems to-date, platform-specific 324 software operations are required for CPUs to enter and exit coherency. 325 However, newer systems exist where CPUs' entry to and exit from coherency 326 is managed in hardware. Such systems require software to only initiate these 327 operations, and the rest is managed in hardware, minimizing active software 328 management. In such systems, this boolean option enables TF-A to carry out 329 build and run-time optimizations during boot and power management operations. 330 This option defaults to 0 and if it is enabled, then it implies 331 ``WARMBOOT_ENABLE_DCACHE_EARLY`` is also enabled. 332 333 If this flag is disabled while the platform which TF-A is compiled for 334 includes cores that manage coherency in hardware, then a compilation error is 335 generated. This is based on the fact that a system cannot have, at the same 336 time, cores that manage coherency in hardware and cores that don't. In other 337 words, a platform cannot have, at the same time, cores that require 338 ``HW_ASSISTED_COHERENCY=1`` and cores that require 339 ``HW_ASSISTED_COHERENCY=0``. 340 341 Note that, when ``HW_ASSISTED_COHERENCY`` is enabled, version 2 of 342 translation library (xlat tables v2) must be used; version 1 of translation 343 library is not supported. 344 345- ``JUNO_AARCH32_EL3_RUNTIME``: This build flag enables you to execute EL3 346 runtime software in AArch32 mode, which is required to run AArch32 on Juno. 347 By default this flag is set to '0'. Enabling this flag builds BL1 and BL2 in 348 AArch64 and facilitates the loading of ``SP_MIN`` and BL33 as AArch32 executable 349 images. 350 351- ``KEY_ALG``: This build flag enables the user to select the algorithm to be 352 used for generating the PKCS keys and subsequent signing of the certificate. 353 It accepts 3 values: ``rsa``, ``rsa_1_5`` and ``ecdsa``. The option 354 ``rsa_1_5`` is the legacy PKCS#1 RSA 1.5 algorithm which is not TBBR 355 compliant and is retained only for compatibility. The default value of this 356 flag is ``rsa`` which is the TBBR compliant PKCS#1 RSA 2.1 scheme. 357 358- ``KEY_SIZE``: This build flag enables the user to select the key size for 359 the algorithm specified by ``KEY_ALG``. The valid values for ``KEY_SIZE`` 360 depend on the chosen algorithm and the cryptographic module. 361 362 +-----------+------------------------------------+ 363 | KEY_ALG | Possible key sizes | 364 +===========+====================================+ 365 | rsa | 1024 , 2048 (default), 3072, 4096* | 366 +-----------+------------------------------------+ 367 | ecdsa | unavailable | 368 +-----------+------------------------------------+ 369 370 * Only 2048 bits size is available with CryptoCell 712 SBROM release 1. 371 Only 3072 bits size is available with CryptoCell 712 SBROM release 2. 372 373- ``HASH_ALG``: This build flag enables the user to select the secure hash 374 algorithm. It accepts 3 values: ``sha256``, ``sha384`` and ``sha512``. 375 The default value of this flag is ``sha256``. 376 377- ``LDFLAGS``: Extra user options appended to the linkers' command line in 378 addition to the one set by the build system. 379 380- ``LOG_LEVEL``: Chooses the log level, which controls the amount of console log 381 output compiled into the build. This should be one of the following: 382 383 :: 384 385 0 (LOG_LEVEL_NONE) 386 10 (LOG_LEVEL_ERROR) 387 20 (LOG_LEVEL_NOTICE) 388 30 (LOG_LEVEL_WARNING) 389 40 (LOG_LEVEL_INFO) 390 50 (LOG_LEVEL_VERBOSE) 391 392 All log output up to and including the selected log level is compiled into 393 the build. The default value is 40 in debug builds and 20 in release builds. 394 395- ``NON_TRUSTED_WORLD_KEY``: This option is used when ``GENERATE_COT=1``. It 396 specifies the file that contains the Non-Trusted World private key in PEM 397 format. If ``SAVE_KEYS=1``, this file name will be used to save the key. 398 399- ``NS_BL2U``: Path to NS_BL2U image in the host file system. This image is 400 optional. It is only needed if the platform makefile specifies that it 401 is required in order to build the ``fwu_fip`` target. 402 403- ``NS_TIMER_SWITCH``: Enable save and restore for non-secure timer register 404 contents upon world switch. It can take either 0 (don't save and restore) or 405 1 (do save and restore). 0 is the default. An SPD may set this to 1 if it 406 wants the timer registers to be saved and restored. 407 408- ``OVERRIDE_LIBC``: This option allows platforms to override the default libc 409 for the BL image. It can be either 0 (include) or 1 (remove). The default 410 value is 0. 411 412- ``PL011_GENERIC_UART``: Boolean option to indicate the PL011 driver that 413 the underlying hardware is not a full PL011 UART but a minimally compliant 414 generic UART, which is a subset of the PL011. The driver will not access 415 any register that is not part of the SBSA generic UART specification. 416 Default value is 0 (a full PL011 compliant UART is present). 417 418- ``PLAT``: Choose a platform to build TF-A for. The chosen platform name 419 must be subdirectory of any depth under ``plat/``, and must contain a 420 platform makefile named ``platform.mk``. For example, to build TF-A for the 421 Arm Juno board, select PLAT=juno. 422 423- ``PRELOADED_BL33_BASE``: This option enables booting a preloaded BL33 image 424 instead of the normal boot flow. When defined, it must specify the entry 425 point address for the preloaded BL33 image. This option is incompatible with 426 ``EL3_PAYLOAD_BASE``. If both are defined, ``EL3_PAYLOAD_BASE`` has priority 427 over ``PRELOADED_BL33_BASE``. 428 429- ``PROGRAMMABLE_RESET_ADDRESS``: This option indicates whether the reset 430 vector address can be programmed or is fixed on the platform. It can take 431 either 0 (fixed) or 1 (programmable). Default is 0. If the platform has a 432 programmable reset address, it is expected that a CPU will start executing 433 code directly at the right address, both on a cold and warm reset. In this 434 case, there is no need to identify the entrypoint on boot and the boot path 435 can be optimised. The ``plat_get_my_entrypoint()`` platform porting interface 436 does not need to be implemented in this case. 437 438- ``PSCI_EXTENDED_STATE_ID``: As per PSCI1.0 Specification, there are 2 formats 439 possible for the PSCI power-state parameter: original and extended State-ID 440 formats. This flag if set to 1, configures the generic PSCI layer to use the 441 extended format. The default value of this flag is 0, which means by default 442 the original power-state format is used by the PSCI implementation. This flag 443 should be specified by the platform makefile and it governs the return value 444 of PSCI_FEATURES API for CPU_SUSPEND smc function id. When this option is 445 enabled on Arm platforms, the option ``ARM_RECOM_STATE_ID_ENC`` needs to be 446 set to 1 as well. 447 448- ``RAS_EXTENSION``: When set to ``1``, enable Armv8.2 RAS features. RAS features 449 are an optional extension for pre-Armv8.2 CPUs, but are mandatory for Armv8.2 450 or later CPUs. 451 452 When ``RAS_EXTENSION`` is set to ``1``, ``HANDLE_EA_EL3_FIRST`` must also be 453 set to ``1``. 454 455 This option is disabled by default. 456 457- ``RESET_TO_BL31``: Enable BL31 entrypoint as the CPU reset vector instead 458 of the BL1 entrypoint. It can take the value 0 (CPU reset to BL1 459 entrypoint) or 1 (CPU reset to BL31 entrypoint). 460 The default value is 0. 461 462- ``RESET_TO_SP_MIN``: SP_MIN is the minimal AArch32 Secure Payload provided 463 in TF-A. This flag configures SP_MIN entrypoint as the CPU reset vector 464 instead of the BL1 entrypoint. It can take the value 0 (CPU reset to BL1 465 entrypoint) or 1 (CPU reset to SP_MIN entrypoint). The default value is 0. 466 467- ``ROT_KEY``: This option is used when ``GENERATE_COT=1``. It specifies the 468 file that contains the ROT private key in PEM format. If ``SAVE_KEYS=1``, this 469 file name will be used to save the key. 470 471- ``SAVE_KEYS``: This option is used when ``GENERATE_COT=1``. It tells the 472 certificate generation tool to save the keys used to establish the Chain of 473 Trust. Allowed options are '0' or '1'. Default is '0' (do not save). 474 475- ``SCP_BL2``: Path to SCP_BL2 image in the host file system. This image is optional. 476 If a SCP_BL2 image is present then this option must be passed for the ``fip`` 477 target. 478 479- ``SCP_BL2_KEY``: This option is used when ``GENERATE_COT=1``. It specifies the 480 file that contains the SCP_BL2 private key in PEM format. If ``SAVE_KEYS=1``, 481 this file name will be used to save the key. 482 483- ``SCP_BL2U``: Path to SCP_BL2U image in the host file system. This image is 484 optional. It is only needed if the platform makefile specifies that it 485 is required in order to build the ``fwu_fip`` target. 486 487- ``SDEI_SUPPORT``: Setting this to ``1`` enables support for Software 488 Delegated Exception Interface to BL31 image. This defaults to ``0``. 489 490 When set to ``1``, the build option ``EL3_EXCEPTION_HANDLING`` must also be 491 set to ``1``. 492 493- ``SEPARATE_CODE_AND_RODATA``: Whether code and read-only data should be 494 isolated on separate memory pages. This is a trade-off between security and 495 memory usage. See "Isolating code and read-only data on separate memory 496 pages" section in :ref:`Firmware Design`. This flag is disabled by default and 497 affects all BL images. 498 499- ``SPD``: Choose a Secure Payload Dispatcher component to be built into TF-A. 500 This build option is only valid if ``ARCH=aarch64``. The value should be 501 the path to the directory containing the SPD source, relative to 502 ``services/spd/``; the directory is expected to contain a makefile called 503 ``<spd-value>.mk``. 504 505- ``SPIN_ON_BL1_EXIT``: This option introduces an infinite loop in BL1. It can 506 take either 0 (no loop) or 1 (add a loop). 0 is the default. This loop stops 507 execution in BL1 just before handing over to BL31. At this point, all 508 firmware images have been loaded in memory, and the MMU and caches are 509 turned off. Refer to the "Debugging options" section for more details. 510 511- ``SPM_MM`` : Boolean option to enable the Management Mode (MM)-based Secure 512 Partition Manager (SPM) implementation. The default value is ``0``. 513 514- ``SP_MIN_WITH_SECURE_FIQ``: Boolean flag to indicate the SP_MIN handles 515 secure interrupts (caught through the FIQ line). Platforms can enable 516 this directive if they need to handle such interruption. When enabled, 517 the FIQ are handled in monitor mode and non secure world is not allowed 518 to mask these events. Platforms that enable FIQ handling in SP_MIN shall 519 implement the api ``sp_min_plat_fiq_handler()``. The default value is 0. 520 521- ``TRUSTED_BOARD_BOOT``: Boolean flag to include support for the Trusted Board 522 Boot feature. When set to '1', BL1 and BL2 images include support to load 523 and verify the certificates and images in a FIP, and BL1 includes support 524 for the Firmware Update. The default value is '0'. Generation and inclusion 525 of certificates in the FIP and FWU_FIP depends upon the value of the 526 ``GENERATE_COT`` option. 527 528 .. warning:: 529 This option depends on ``CREATE_KEYS`` to be enabled. If the keys 530 already exist in disk, they will be overwritten without further notice. 531 532- ``TRUSTED_WORLD_KEY``: This option is used when ``GENERATE_COT=1``. It 533 specifies the file that contains the Trusted World private key in PEM 534 format. If ``SAVE_KEYS=1``, this file name will be used to save the key. 535 536- ``TSP_INIT_ASYNC``: Choose BL32 initialization method as asynchronous or 537 synchronous, (see "Initializing a BL32 Image" section in 538 :ref:`Firmware Design`). It can take the value 0 (BL32 is initialized using 539 synchronous method) or 1 (BL32 is initialized using asynchronous method). 540 Default is 0. 541 542- ``TSP_NS_INTR_ASYNC_PREEMPT``: A non zero value enables the interrupt 543 routing model which routes non-secure interrupts asynchronously from TSP 544 to EL3 causing immediate preemption of TSP. The EL3 is responsible 545 for saving and restoring the TSP context in this routing model. The 546 default routing model (when the value is 0) is to route non-secure 547 interrupts to TSP allowing it to save its context and hand over 548 synchronously to EL3 via an SMC. 549 550 .. note:: 551 When ``EL3_EXCEPTION_HANDLING`` is ``1``, ``TSP_NS_INTR_ASYNC_PREEMPT`` 552 must also be set to ``1``. 553 554- ``USE_ARM_LINK``: This flag determines whether to enable support for ARM 555 linker. When the ``LINKER`` build variable points to the armlink linker, 556 this flag is enabled automatically. To enable support for armlink, platforms 557 will have to provide a scatter file for the BL image. Currently, Tegra 558 platforms use the armlink support to compile BL3-1 images. 559 560- ``USE_COHERENT_MEM``: This flag determines whether to include the coherent 561 memory region in the BL memory map or not (see "Use of Coherent memory in 562 TF-A" section in :ref:`Firmware Design`). It can take the value 1 563 (Coherent memory region is included) or 0 (Coherent memory region is 564 excluded). Default is 1. 565 566- ``USE_ROMLIB``: This flag determines whether library at ROM will be used. 567 This feature creates a library of functions to be placed in ROM and thus 568 reduces SRAM usage. Refer to :ref:`Library at ROM` for further details. Default 569 is 0. 570 571- ``V``: Verbose build. If assigned anything other than 0, the build commands 572 are printed. Default is 0. 573 574- ``VERSION_STRING``: String used in the log output for each TF-A image. 575 Defaults to a string formed by concatenating the version number, build type 576 and build string. 577 578- ``W``: Warning level. Some compiler warning options of interest have been 579 regrouped and put in the root Makefile. This flag can take the values 0 to 3, 580 each level enabling more warning options. Default is 0. 581 582- ``WARMBOOT_ENABLE_DCACHE_EARLY`` : Boolean option to enable D-cache early on 583 the CPU after warm boot. This is applicable for platforms which do not 584 require interconnect programming to enable cache coherency (eg: single 585 cluster platforms). If this option is enabled, then warm boot path 586 enables D-caches immediately after enabling MMU. This option defaults to 0. 587 588Debugging options 589----------------- 590 591To compile a debug version and make the build more verbose use 592 593.. code:: shell 594 595 make PLAT=<platform> DEBUG=1 V=1 all 596 597AArch64 GCC uses DWARF version 4 debugging symbols by default. Some tools (for 598example DS-5) might not support this and may need an older version of DWARF 599symbols to be emitted by GCC. This can be achieved by using the 600``-gdwarf-<version>`` flag, with the version being set to 2 or 3. Setting the 601version to 2 is recommended for DS-5 versions older than 5.16. 602 603When debugging logic problems it might also be useful to disable all compiler 604optimizations by using ``-O0``. 605 606.. warning:: 607 Using ``-O0`` could cause output images to be larger and base addresses 608 might need to be recalculated (see the **Memory layout on Arm development 609 platforms** section in the :ref:`Firmware Design`). 610 611Extra debug options can be passed to the build system by setting ``CFLAGS`` or 612``LDFLAGS``: 613 614.. code:: shell 615 616 CFLAGS='-O0 -gdwarf-2' \ 617 make PLAT=<platform> DEBUG=1 V=1 all 618 619Note that using ``-Wl,`` style compilation driver options in ``CFLAGS`` will be 620ignored as the linker is called directly. 621 622It is also possible to introduce an infinite loop to help in debugging the 623post-BL2 phase of TF-A. This can be done by rebuilding BL1 with the 624``SPIN_ON_BL1_EXIT=1`` build flag. Refer to the :ref:`build_options_common` 625section. In this case, the developer may take control of the target using a 626debugger when indicated by the console output. When using DS-5, the following 627commands can be used: 628 629:: 630 631 # Stop target execution 632 interrupt 633 634 # 635 # Prepare your debugging environment, e.g. set breakpoints 636 # 637 638 # Jump over the debug loop 639 set var $AARCH64::$Core::$PC = $AARCH64::$Core::$PC + 4 640 641 # Resume execution 642 continue 643 644-------------- 645 646*Copyright (c) 2019, Arm Limited. All rights reserved.* 647