xref: /OK3568_Linux_fs/u-boot/board/freescale/mpc8568mds/mpc8568mds.c (revision 4882a59341e53eb6f0b4789bf948001014eff981)

/*
 * Copyright 2007,2009-2011 Freescale Semiconductor, Inc.
 *
 * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <spd_sdram.h>
#include <i2c.h>
#include <ioports.h>
#include <linux/libfdt.h>
#include <fdt_support.h>

#include "bcsr.h"

const qe_iop_conf_t qe_iop_conf_tab[] = {
	/* GETH1 */
	{4, 10, 1, 0, 2}, /* TxD0 */
	{4,  9, 1, 0, 2}, /* TxD1 */
	{4,  8, 1, 0, 2}, /* TxD2 */
	{4,  7, 1, 0, 2}, /* TxD3 */
	{4, 23, 1, 0, 2}, /* TxD4 */
	{4, 22, 1, 0, 2}, /* TxD5 */
	{4, 21, 1, 0, 2}, /* TxD6 */
	{4, 20, 1, 0, 2}, /* TxD7 */
	{4, 15, 2, 0, 2}, /* RxD0 */
	{4, 14, 2, 0, 2}, /* RxD1 */
	{4, 13, 2, 0, 2}, /* RxD2 */
	{4, 12, 2, 0, 2}, /* RxD3 */
	{4, 29, 2, 0, 2}, /* RxD4 */
	{4, 28, 2, 0, 2}, /* RxD5 */
	{4, 27, 2, 0, 2}, /* RxD6 */
	{4, 26, 2, 0, 2}, /* RxD7 */
	{4, 11, 1, 0, 2}, /* TX_EN */
	{4, 24, 1, 0, 2}, /* TX_ER */
	{4, 16, 2, 0, 2}, /* RX_DV */
	{4, 30, 2, 0, 2}, /* RX_ER */
	{4, 17, 2, 0, 2}, /* RX_CLK */
	{4, 19, 1, 0, 2}, /* GTX_CLK */
	{1, 31, 2, 0, 3}, /* GTX125 */

	/* GETH2 */
	{5, 10, 1, 0, 2}, /* TxD0 */
	{5,  9, 1, 0, 2}, /* TxD1 */
	{5,  8, 1, 0, 2}, /* TxD2 */
	{5,  7, 1, 0, 2}, /* TxD3 */
	{5, 23, 1, 0, 2}, /* TxD4 */
	{5, 22, 1, 0, 2}, /* TxD5 */
	{5, 21, 1, 0, 2}, /* TxD6 */
	{5, 20, 1, 0, 2}, /* TxD7 */
	{5, 15, 2, 0, 2}, /* RxD0 */
	{5, 14, 2, 0, 2}, /* RxD1 */
	{5, 13, 2, 0, 2}, /* RxD2 */
	{5, 12, 2, 0, 2}, /* RxD3 */
	{5, 29, 2, 0, 2}, /* RxD4 */
	{5, 28, 2, 0, 2}, /* RxD5 */
	{5, 27, 2, 0, 3}, /* RxD6 */
	{5, 26, 2, 0, 2}, /* RxD7 */
	{5, 11, 1, 0, 2}, /* TX_EN */
	{5, 24, 1, 0, 2}, /* TX_ER */
	{5, 16, 2, 0, 2}, /* RX_DV */
	{5, 30, 2, 0, 2}, /* RX_ER */
	{5, 17, 2, 0, 2}, /* RX_CLK */
	{5, 19, 1, 0, 2}, /* GTX_CLK */
	{1, 31, 2, 0, 3}, /* GTX125 */
	{4,  6, 3, 0, 2}, /* MDIO */
	{4,  5, 1, 0, 2}, /* MDC */

	/* UART1 */
	{2, 0, 1, 0, 2}, /* UART_SOUT1 */
	{2, 1, 1, 0, 2}, /* UART_RTS1 */
	{2, 2, 2, 0, 2}, /* UART_CTS1 */
	{2, 3, 2, 0, 2}, /* UART_SIN1 */

	{0,  0, 0, 0, QE_IOP_TAB_END}, /* END of table */
};

void local_bus_init(void);

int board_early_init_f (void)
{
	/*
	 * Initialize local bus.
	 */
	local_bus_init ();

	enable_8568mds_duart();
	enable_8568mds_flash_write();
#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2)
	reset_8568mds_uccs();
#endif
#if defined(CONFIG_QE) && !defined(CONFIG_eTSEC_MDIO_BUS)
	enable_8568mds_qe_mdio();
#endif

#ifdef CONFIG_SYS_I2C2_OFFSET
	/* Enable I2C2_SCL and I2C2_SDA */
	volatile struct par_io *port_c;
	port_c = (struct par_io*)(CONFIG_SYS_IMMR + 0xe0140);
	port_c->cpdir2 |= 0x0f000000;
	port_c->cppar2 &= ~0x0f000000;
	port_c->cppar2 |= 0x0a000000;
#endif

	return 0;
}

int checkboard (void)
{
	printf ("Board: 8568 MDS\n");

	return 0;
}

/*
 * Initialize Local Bus
 */
void
local_bus_init(void)
{
	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;

	uint clkdiv;
	sys_info_t sysinfo;

	get_sys_info(&sysinfo);
	clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;

	gur->lbiuiplldcr1 = 0x00078080;
	if (clkdiv == 16) {
		gur->lbiuiplldcr0 = 0x7c0f1bf0;
	} else if (clkdiv == 8) {
		gur->lbiuiplldcr0 = 0x6c0f1bf0;
	} else if (clkdiv == 4) {
		gur->lbiuiplldcr0 = 0x5c0f1bf0;
	}

	lbc->lcrr |= 0x00030000;

	asm("sync;isync;msync");
}

/*
 * Initialize SDRAM memory on the Local Bus.
 */
void lbc_sdram_init(void)
{
#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)

	uint idx;
	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
	uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
	uint lsdmr_common;

	puts("LBC SDRAM: ");
	print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
		   "\n       ");

	/*
	 * Setup SDRAM Base and Option Registers
	 */
	set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
	set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
	asm("msync");

	lbc->lbcr = CONFIG_SYS_LBC_LBCR;
	asm("msync");

	lbc->lsrt = CONFIG_SYS_LBC_LSRT;
	lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
	asm("msync");

	/*
	 * MPC8568 uses "new" 15-16 style addressing.
	 */
	lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
	lsdmr_common |= LSDMR_BSMA1516;

	/*
	 * Issue PRECHARGE ALL command.
	 */
	lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
	asm("sync;msync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	/*
	 * Issue 8 AUTO REFRESH commands.
	 */
	for (idx = 0; idx < 8; idx++) {
		lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
		asm("sync;msync");
		*sdram_addr = 0xff;
		ppcDcbf((unsigned long) sdram_addr);
		udelay(100);
	}

	/*
	 * Issue 8 MODE-set command.
	 */
	lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
	asm("sync;msync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	/*
	 * Issue NORMAL OP command.
	 */
	lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
	asm("sync;msync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(200);    /* Overkill. Must wait > 200 bus cycles */

#endif	/* enable SDRAM init */
}

#if defined(CONFIG_PCI)
#ifndef CONFIG_PCI_PNP
static struct pci_config_table pci_mpc8568mds_config_table[] = {
	{
	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
	 pci_cfgfunc_config_device,
	 {PCI_ENET0_IOADDR,
	  PCI_ENET0_MEMADDR,
	  PCI_COMMON_MEMORY | PCI_COMMAND_MASTER}
	 },
	{}
};
#endif

static struct pci_controller pci1_hose;
#endif	/* CONFIG_PCI */

/*
 * pib_init() -- Initialize the PCA9555 IO expander on the PIB board
 */
void
pib_init(void)
{
	u8 val8, orig_i2c_bus;
	/*
	 * Assign PIB PMC2/3 to PCI bus
	 */

	/*switch temporarily to I2C bus #2 */
	orig_i2c_bus = i2c_get_bus_num();
	i2c_set_bus_num(1);

	val8 = 0x00;
	i2c_write(0x23, 0x6, 1, &val8, 1);
	i2c_write(0x23, 0x7, 1, &val8, 1);
	val8 = 0xff;
	i2c_write(0x23, 0x2, 1, &val8, 1);
	i2c_write(0x23, 0x3, 1, &val8, 1);

	val8 = 0x00;
	i2c_write(0x26, 0x6, 1, &val8, 1);
	val8 = 0x34;
	i2c_write(0x26, 0x7, 1, &val8, 1);
	val8 = 0xf9;
	i2c_write(0x26, 0x2, 1, &val8, 1);
	val8 = 0xff;
	i2c_write(0x26, 0x3, 1, &val8, 1);

	val8 = 0x00;
	i2c_write(0x27, 0x6, 1, &val8, 1);
	i2c_write(0x27, 0x7, 1, &val8, 1);
	val8 = 0xff;
	i2c_write(0x27, 0x2, 1, &val8, 1);
	val8 = 0xef;
	i2c_write(0x27, 0x3, 1, &val8, 1);

	asm("eieio");
	i2c_set_bus_num(orig_i2c_bus);
}

#ifdef CONFIG_PCI
void pci_init_board(void)
{
	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
	int first_free_busno = 0;
#ifdef CONFIG_PCI1
	struct fsl_pci_info pci_info;
	u32 devdisr, pordevsr, io_sel;
	u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel;

	devdisr = in_be32(&gur->devdisr);
	pordevsr = in_be32(&gur->pordevsr);
	porpllsr = in_be32(&gur->porpllsr);
	io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;

	debug ("   pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel);

	pci_speed = 66666000;
	pci_32 = 1;
	pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
	pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;

	if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
		SET_STD_PCI_INFO(pci_info, 1);
		set_next_law(pci_info.mem_phys,
			law_size_bits(pci_info.mem_size), pci_info.law);
		set_next_law(pci_info.io_phys,
			law_size_bits(pci_info.io_size), pci_info.law);

		pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs);
		printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n",
			(pci_32) ? 32 : 64,
			(pci_speed == 33333000) ? "33" :
			(pci_speed == 66666000) ? "66" : "unknown",
			pci_clk_sel ? "sync" : "async",
			pci_agent ? "agent" : "host",
			pci_arb ? "arbiter" : "external-arbiter",
			pci_info.regs);

#ifndef CONFIG_PCI_PNP
		pci1_hose.config_table = pci_mpc8568mds_config_table;
#endif
		first_free_busno = fsl_pci_init_port(&pci_info,
					&pci1_hose, first_free_busno);
	} else {
		printf("PCI: disabled\n");
	}

	puts("\n");
#else
	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */
#endif

	fsl_pcie_init_board(first_free_busno);
}
#endif /* CONFIG_PCI */

#if defined(CONFIG_OF_BOARD_SETUP)
int ft_board_setup(void *blob, bd_t *bd)
{
	ft_cpu_setup(blob, bd);

	FT_FSL_PCI_SETUP;

	return 0;
}
#endif