xref: /OK3568_Linux_fs/u-boot/arch/arm/mach-imx/mx6/opos6ul.c (revision 4882a59341e53eb6f0b4789bf948001014eff981)

/*
 * Copyright (C) 2017 Armadeus Systems
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/mx6ul_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/io.h>
#include <common.h>
#include <environment.h>
#include <fsl_esdhc.h>
#include <mmc.h>

DECLARE_GLOBAL_DATA_PTR;

#ifdef CONFIG_FEC_MXC
#include <miiphy.h>

#define MDIO_PAD_CTRL ( \
	PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
	PAD_CTL_DSE_40ohm \
)

#define ENET_PAD_CTRL_PU ( \
	PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
	PAD_CTL_DSE_40ohm \
)

#define ENET_PAD_CTRL_PD ( \
	PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
	PAD_CTL_DSE_40ohm \
)

#define ENET_CLK_PAD_CTRL ( \
	PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
	PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST \
)

static iomux_v3_cfg_t const fec1_pads[] = {
	MX6_PAD_GPIO1_IO06__ENET1_MDIO        | MUX_PAD_CTRL(MDIO_PAD_CTRL),
	MX6_PAD_GPIO1_IO07__ENET1_MDC         | MUX_PAD_CTRL(MDIO_PAD_CTRL),
	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER      | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN      | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN      | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
	/* PHY Int */
	MX6_PAD_NAND_DQS__GPIO4_IO16          | MUX_PAD_CTRL(ENET_PAD_CTRL_PU),
	/* PHY Reset */
	MX6_PAD_NAND_DATA00__GPIO4_IO02       | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
};

int board_phy_config(struct phy_device *phydev)
{
	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);

	if (phydev->drv->config)
		phydev->drv->config(phydev);

	return 0;
}

int board_eth_init(bd_t *bis)
{
	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
	struct gpio_desc rst;
	int ret;

	/* Use 50M anatop loopback REF_CLK1 for ENET1,
	 * clear gpr1[13], set gpr1[17] */
	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);

	ret = enable_fec_anatop_clock(0, ENET_50MHZ);
	if (ret)
		return ret;

	enable_enet_clk(1);

	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));

	ret = dm_gpio_lookup_name("GPIO4_2", &rst);
	if (ret) {
		printf("Cannot get GPIO4_2\n");
		return ret;
	}

	ret = dm_gpio_request(&rst, "phy-rst");
	if (ret) {
		printf("Cannot request GPIO4_2\n");
		return ret;
	}

	dm_gpio_set_dir_flags(&rst, GPIOD_IS_OUT);
	dm_gpio_set_value(&rst, 0);
	udelay(1000);
	dm_gpio_set_value(&rst, 1);

	return fecmxc_initialize(bis);
}
#endif /* CONFIG_FEC_MXC */

int board_init(void)
{
	/* Address of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

	return 0;
}

int __weak opos6ul_board_late_init(void)
{
	return 0;
}

int board_late_init(void)
{
	struct src *psrc = (struct src *)SRC_BASE_ADDR;
	unsigned reg = readl(&psrc->sbmr2);

	/* In bootstrap don't use the env vars */
	if (((reg & 0x3000000) >> 24) == 0x1) {
		set_default_env(NULL);
		env_set("preboot", "");
	}

	return opos6ul_board_late_init();
}

int board_mmc_getcd(struct mmc *mmc)
{
	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
	return cfg->esdhc_base == USDHC1_BASE_ADDR;
}

int dram_init(void)
{
	gd->ram_size = imx_ddr_size();

	return 0;
}

#ifdef CONFIG_SPL_BUILD
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/opos6ul.h>
#include <linux/libfdt.h>
#include <spl.h>

#define USDHC_PAD_CTRL (                                       \
	PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_MED | \
	PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST                   \
)

struct fsl_esdhc_cfg usdhc_cfg[1] = {
	{USDHC1_BASE_ADDR, 0, 8},
};

static iomux_v3_cfg_t const usdhc1_pads[] = {
	MX6_PAD_SD1_CLK__USDHC1_CLK        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_CMD__USDHC1_CMD        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA0__USDHC1_DATA0    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA1__USDHC1_DATA1    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA2__USDHC1_DATA2    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD1_DATA3__USDHC1_DATA3    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_NAND_READY_B__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_NAND_CE0_B__USDHC1_DATA5   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_NAND_CE1_B__USDHC1_DATA6   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_NAND_CLE__USDHC1_DATA7     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};

static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
	.grp_addds = 0x00000030,
	.grp_ddrmode_ctl = 0x00020000,
	.grp_b0ds = 0x00000030,
	.grp_ctlds = 0x00000030,
	.grp_b1ds = 0x00000030,
	.grp_ddrpke = 0x00000000,
	.grp_ddrmode = 0x00020000,
	.grp_ddr_type = 0x000c0000,
};

static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
	.dram_dqm0 = 0x00000030,
	.dram_dqm1 = 0x00000030,
	.dram_ras = 0x00000030,
	.dram_cas = 0x00000030,
	.dram_odt0 = 0x00000030,
	.dram_odt1 = 0x00000030,
	.dram_sdba2 = 0x00000000,
	.dram_sdclk_0 = 0x00000008,
	.dram_sdqs0 = 0x00000038,
	.dram_sdqs1 = 0x00000030,
	.dram_reset = 0x00000030,
};

static struct mx6_mmdc_calibration mx6_mmcd_calib = {
	.p0_mpwldectrl0 = 0x00070007,
	.p0_mpdgctrl0 = 0x41490145,
	.p0_mprddlctl = 0x40404546,
	.p0_mpwrdlctl = 0x4040524D,
};

struct mx6_ddr_sysinfo ddr_sysinfo = {
	.dsize = 0,
	.cs_density = 20,
	.ncs = 1,
	.cs1_mirror = 0,
	.rtt_wr = 2,
	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
	.walat = 1,		/* Write additional latency */
	.ralat = 5,		/* Read additional latency */
	.mif3_mode = 3,		/* Command prediction working mode */
	.bi_on = 1,		/* Bank interleaving enabled */
	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
	.ddr_type = DDR_TYPE_DDR3,
};

static struct mx6_ddr3_cfg mem_ddr = {
	.mem_speed = 800,
	.density = 2,
	.width = 16,
	.banks = 8,
	.rowaddr = 14,
	.coladdr = 10,
	.pagesz = 2,
	.trcd = 1500,
	.trcmin = 5250,
	.trasmin = 3750,
};

int board_mmc_init(bd_t *bis)
{
	imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
}

static void ccgr_init(void)
{
	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;

	writel(0xFFFFFFFF, &ccm->CCGR0);
	writel(0xFFFFFFFF, &ccm->CCGR1);
	writel(0xFFFFFFFF, &ccm->CCGR2);
	writel(0xFFFFFFFF, &ccm->CCGR3);
	writel(0xFFFFFFFF, &ccm->CCGR4);
	writel(0xFFFFFFFF, &ccm->CCGR5);
	writel(0xFFFFFFFF, &ccm->CCGR6);
	writel(0xFFFFFFFF, &ccm->CCGR7);
}

static void spl_dram_init(void)
{
	struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
	struct fuse_bank *bank = &ocotp->bank[4];
	struct fuse_bank4_regs *fuse =
		(struct fuse_bank4_regs *)bank->fuse_regs;
	int reg = readl(&fuse->gp1);

	/* 512MB of RAM */
	if (reg & 0x1) {
		mem_ddr.density = 4;
		mem_ddr.rowaddr = 15;
		mem_ddr.trcd = 1375;
		mem_ddr.trcmin = 4875;
		mem_ddr.trasmin = 3500;
	}

	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
}

void board_init_f(ulong dummy)
{
	ccgr_init();

	/* setup AIPS and disable watchdog */
	arch_cpu_init();

	/* setup GP timer */
	timer_init();

	/* UART clocks enabled and gd valid - init serial console */
	opos6ul_setup_uart_debug();
	preloader_console_init();

	/* DDR initialization */
	spl_dram_init();
}
#endif /* CONFIG_SPL_BUILD */