xref: /OK3568_Linux_fs/kernel/include/linux/ssb/ssb_driver_extif.h (revision 4882a59341e53eb6f0b4789bf948001014eff981)

/* SPDX-License-Identifier: GPL-2.0-only */
/*
 * Hardware-specific External Interface I/O core definitions
 * for the BCM47xx family of SiliconBackplane-based chips.
 *
 * The External Interface core supports a total of three external chip selects
 * supporting external interfaces. One of the external chip selects is
 * used for Flash, one is used for PCMCIA, and the other may be
 * programmed to support either a synchronous interface or an
 * asynchronous interface. The asynchronous interface can be used to
 * support external devices such as UARTs and the BCM2019 Bluetooth
 * baseband processor.
 * The external interface core also contains 2 on-chip 16550 UARTs, clock
 * frequency control, a watchdog interrupt timer, and a GPIO interface.
 *
 * Copyright 2005, Broadcom Corporation
 * Copyright 2006, Michael Buesch
 */
#ifndef LINUX_SSB_EXTIFCORE_H_
#define LINUX_SSB_EXTIFCORE_H_

/* external interface address space */
#define	SSB_EXTIF_PCMCIA_MEMBASE(x)	(x)
#define	SSB_EXTIF_PCMCIA_IOBASE(x)	((x) + 0x100000)
#define	SSB_EXTIF_PCMCIA_CFGBASE(x)	((x) + 0x200000)
#define	SSB_EXTIF_CFGIF_BASE(x)		((x) + 0x800000)
#define	SSB_EXTIF_FLASH_BASE(x)		((x) + 0xc00000)

#define SSB_EXTIF_NR_GPIOOUT		5
/* GPIO NOTE:
 * The multiple instances of output and output enable registers
 * are present to allow driver software for multiple cores to control
 * gpio outputs without needing to share a single register pair.
 * Use the following helper macro to get a register offset value.
 */
#define SSB_EXTIF_GPIO_OUT(index)	({		\
	BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT);	\
	SSB_EXTIF_GPIO_OUT_BASE + ((index) * 8);	\
					})
#define SSB_EXTIF_GPIO_OUTEN(index)	({		\
	BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT);	\
	SSB_EXTIF_GPIO_OUTEN_BASE + ((index) * 8);	\
					})

/** EXTIF core registers **/

#define SSB_EXTIF_CTL			0x0000
#define  SSB_EXTIF_CTL_UARTEN		(1 << 0) /* UART enable */
#define SSB_EXTIF_EXTSTAT		0x0004
#define  SSB_EXTIF_EXTSTAT_EMODE	(1 << 0) /* Endian mode (ro) */
#define  SSB_EXTIF_EXTSTAT_EIRQPIN	(1 << 1) /* External interrupt pin (ro) */
#define  SSB_EXTIF_EXTSTAT_GPIOIRQPIN	(1 << 2) /* GPIO interrupt pin (ro) */
#define SSB_EXTIF_PCMCIA_CFG		0x0010
#define SSB_EXTIF_PCMCIA_MEMWAIT	0x0014
#define SSB_EXTIF_PCMCIA_ATTRWAIT	0x0018
#define SSB_EXTIF_PCMCIA_IOWAIT		0x001C
#define SSB_EXTIF_PROG_CFG		0x0020
#define SSB_EXTIF_PROG_WAITCNT		0x0024
#define SSB_EXTIF_FLASH_CFG		0x0028
#define SSB_EXTIF_FLASH_WAITCNT		0x002C
#define SSB_EXTIF_WATCHDOG		0x0040
#define SSB_EXTIF_CLOCK_N		0x0044
#define SSB_EXTIF_CLOCK_SB		0x0048
#define SSB_EXTIF_CLOCK_PCI		0x004C
#define SSB_EXTIF_CLOCK_MII		0x0050
#define SSB_EXTIF_GPIO_IN		0x0060
#define SSB_EXTIF_GPIO_OUT_BASE		0x0064
#define SSB_EXTIF_GPIO_OUTEN_BASE	0x0068
#define SSB_EXTIF_EJTAG_OUTEN		0x0090
#define SSB_EXTIF_GPIO_INTPOL		0x0094
#define SSB_EXTIF_GPIO_INTMASK		0x0098
#define SSB_EXTIF_UART_DATA		0x0300
#define SSB_EXTIF_UART_TIMER		0x0310
#define SSB_EXTIF_UART_FCR		0x0320
#define SSB_EXTIF_UART_LCR		0x0330
#define SSB_EXTIF_UART_MCR		0x0340
#define SSB_EXTIF_UART_LSR		0x0350
#define SSB_EXTIF_UART_MSR		0x0360
#define SSB_EXTIF_UART_SCRATCH		0x0370




/* pcmcia/prog/flash_config */
#define	SSB_EXTCFG_EN			(1 << 0)	/* enable */
#define	SSB_EXTCFG_MODE			0xE		/* mode */
#define	SSB_EXTCFG_MODE_SHIFT		1
#define	 SSB_EXTCFG_MODE_FLASH		0x0		/* flash/asynchronous mode */
#define	 SSB_EXTCFG_MODE_SYNC		0x2		/* synchronous mode */
#define	 SSB_EXTCFG_MODE_PCMCIA		0x4		/* pcmcia mode */
#define	SSB_EXTCFG_DS16			(1 << 4)	/* destsize:  0=8bit, 1=16bit */
#define	SSB_EXTCFG_BSWAP		(1 << 5)	/* byteswap */
#define	SSB_EXTCFG_CLKDIV		0xC0		/* clock divider */
#define	SSB_EXTCFG_CLKDIV_SHIFT		6
#define	 SSB_EXTCFG_CLKDIV_2		0x0		/* backplane/2 */
#define	 SSB_EXTCFG_CLKDIV_3		0x40		/* backplane/3 */
#define	 SSB_EXTCFG_CLKDIV_4		0x80		/* backplane/4 */
#define	SSB_EXTCFG_CLKEN		(1 << 8)	/* clock enable */
#define	SSB_EXTCFG_STROBE		(1 << 9)	/* size/bytestrobe (synch only) */

/* pcmcia_memwait */
#define	SSB_PCMCIA_MEMW_0		0x0000003F	/* waitcount0 */
#define	SSB_PCMCIA_MEMW_1		0x00001F00	/* waitcount1 */
#define	SSB_PCMCIA_MEMW_1_SHIFT		8
#define	SSB_PCMCIA_MEMW_2		0x001F0000	/* waitcount2 */
#define	SSB_PCMCIA_MEMW_2_SHIFT		16
#define	SSB_PCMCIA_MEMW_3		0x1F000000	/* waitcount3 */
#define	SSB_PCMCIA_MEMW_3_SHIFT		24

/* pcmcia_attrwait */
#define	SSB_PCMCIA_ATTW_0		0x0000003F	/* waitcount0 */
#define	SSB_PCMCIA_ATTW_1		0x00001F00	/* waitcount1 */
#define	SSB_PCMCIA_ATTW_1_SHIFT		8
#define	SSB_PCMCIA_ATTW_2		0x001F0000	/* waitcount2 */
#define	SSB_PCMCIA_ATTW_2_SHIFT		16
#define	SSB_PCMCIA_ATTW_3		0x1F000000	/* waitcount3 */
#define	SSB_PCMCIA_ATTW_3_SHIFT		24

/* pcmcia_iowait */
#define	SSB_PCMCIA_IOW_0		0x0000003F	/* waitcount0 */
#define	SSB_PCMCIA_IOW_1		0x00001F00	/* waitcount1 */
#define	SSB_PCMCIA_IOW_1_SHIFT		8
#define	SSB_PCMCIA_IOW_2		0x001F0000	/* waitcount2 */
#define	SSB_PCMCIA_IOW_2_SHIFT		16
#define	SSB_PCMCIA_IOW_3		0x1F000000	/* waitcount3 */
#define	SSB_PCMCIA_IOW_3_SHIFT		24

/* prog_waitcount */
#define	SSB_PROG_WCNT_0			0x0000001F	/* waitcount0 */
#define	SSB_PROG_WCNT_1			0x00001F00	/* waitcount1 */
#define	SSB_PROG_WCNT_1_SHIFT		8
#define	SSB_PROG_WCNT_2			0x001F0000	/* waitcount2 */
#define	SSB_PROG_WCNT_2_SHIFT		16
#define	SSB_PROG_WCNT_3			0x1F000000	/* waitcount3 */
#define	SSB_PROG_WCNT_3_SHIFT		24

#define SSB_PROG_W0			0x0000000C
#define SSB_PROG_W1			0x00000A00
#define SSB_PROG_W2			0x00020000
#define SSB_PROG_W3			0x01000000

/* flash_waitcount */
#define	SSB_FLASH_WCNT_0		0x0000001F	/* waitcount0 */
#define	SSB_FLASH_WCNT_1		0x00001F00	/* waitcount1 */
#define	SSB_FLASH_WCNT_1_SHIFT		8
#define	SSB_FLASH_WCNT_2		0x001F0000	/* waitcount2 */
#define	SSB_FLASH_WCNT_2_SHIFT		16
#define	SSB_FLASH_WCNT_3		0x1F000000	/* waitcount3 */
#define	SSB_FLASH_WCNT_3_SHIFT		24

/* watchdog */
#define SSB_EXTIF_WATCHDOG_CLK		48000000	/* Hz */

#define SSB_EXTIF_WATCHDOG_MAX_TIMER	((1 << 28) - 1)
#define SSB_EXTIF_WATCHDOG_MAX_TIMER_MS	(SSB_EXTIF_WATCHDOG_MAX_TIMER \
					 / (SSB_EXTIF_WATCHDOG_CLK / 1000))


#ifdef CONFIG_SSB_DRIVER_EXTIF

struct ssb_extif {
	struct ssb_device *dev;
	spinlock_t gpio_lock;
};

static inline bool ssb_extif_available(struct ssb_extif *extif)
{
	return (extif->dev != NULL);
}

extern void ssb_extif_get_clockcontrol(struct ssb_extif *extif,
			               u32 *plltype, u32 *n, u32 *m);

extern void ssb_extif_timing_init(struct ssb_extif *extif,
				  unsigned long ns);

extern u32 ssb_extif_watchdog_timer_set(struct ssb_extif *extif, u32 ticks);

/* Extif GPIO pin access */
u32 ssb_extif_gpio_in(struct ssb_extif *extif, u32 mask);
u32 ssb_extif_gpio_out(struct ssb_extif *extif, u32 mask, u32 value);
u32 ssb_extif_gpio_outen(struct ssb_extif *extif, u32 mask, u32 value);
u32 ssb_extif_gpio_polarity(struct ssb_extif *extif, u32 mask, u32 value);
u32 ssb_extif_gpio_intmask(struct ssb_extif *extif, u32 mask, u32 value);

#ifdef CONFIG_SSB_SERIAL
extern int ssb_extif_serial_init(struct ssb_extif *extif,
				 struct ssb_serial_port *ports);
#endif /* CONFIG_SSB_SERIAL */


#else /* CONFIG_SSB_DRIVER_EXTIF */
/* extif disabled */

struct ssb_extif {
};

static inline bool ssb_extif_available(struct ssb_extif *extif)
{
	return 0;
}

static inline
void ssb_extif_get_clockcontrol(struct ssb_extif *extif,
			        u32 *plltype, u32 *n, u32 *m)
{
}

static inline
void ssb_extif_timing_init(struct ssb_extif *extif, unsigned long ns)
{
}

static inline
u32 ssb_extif_watchdog_timer_set(struct ssb_extif *extif, u32 ticks)
{
	return 0;
}

static inline u32 ssb_extif_gpio_in(struct ssb_extif *extif, u32 mask)
{
	return 0;
}

static inline u32 ssb_extif_gpio_out(struct ssb_extif *extif, u32 mask,
				     u32 value)
{
	return 0;
}

static inline u32 ssb_extif_gpio_outen(struct ssb_extif *extif, u32 mask,
				       u32 value)
{
	return 0;
}

static inline u32 ssb_extif_gpio_polarity(struct ssb_extif *extif, u32 mask,
					  u32 value)
{
	return 0;
}

static inline u32 ssb_extif_gpio_intmask(struct ssb_extif *extif, u32 mask,
					 u32 value)
{
	return 0;
}

#ifdef CONFIG_SSB_SERIAL
static inline int ssb_extif_serial_init(struct ssb_extif *extif,
					struct ssb_serial_port *ports)
{
	return 0;
}
#endif /* CONFIG_SSB_SERIAL */

#endif /* CONFIG_SSB_DRIVER_EXTIF */
#endif /* LINUX_SSB_EXTIFCORE_H_ */