xref: /OK3568_Linux_fs/kernel/drivers/net/wireless/realtek/rtlwifi/rtl8192ee/pwrseq.h (revision 4882a59341e53eb6f0b4789bf948001014eff981)

/* SPDX-License-Identifier: GPL-2.0 */
/* Copyright(c) 2009-2014  Realtek Corporation.*/

#ifndef __RTL92E_PWRSEQ_H__
#define __RTL92E_PWRSEQ_H__

#include "../pwrseqcmd.h"
/**
 *	Check document WM-20110607-Paul-RTL8192E_Power_Architecture-R02.vsd
 *	There are 6 HW Power States:
 *	0: POFF--Power Off
 *	1: PDN--Power Down
 *	2: CARDEMU--Card Emulation
 *	3: ACT--Active Mode
 *	4: LPS--Low Power State
 *	5: SUS--Suspend
 *
 *	The transision from different states are defined below
 *	TRANS_CARDEMU_TO_ACT
 *	TRANS_ACT_TO_CARDEMU
 *	TRANS_CARDEMU_TO_SUS
 *	TRANS_SUS_TO_CARDEMU
 *	TRANS_CARDEMU_TO_PDN
 *	TRANS_ACT_TO_LPS
 *	TRANS_LPS_TO_ACT
 *
 *	TRANS_END
 *	PWR SEQ Version: rtl8192E_PwrSeq_V09.h
 */

#define	RTL8192E_TRANS_CARDEMU_TO_ACT_STEPS	18
#define	RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS	18
#define	RTL8192E_TRANS_CARDEMU_TO_SUS_STEPS	18
#define	RTL8192E_TRANS_SUS_TO_CARDEMU_STEPS	18
#define	RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS	18
#define	RTL8192E_TRANS_PDN_TO_CARDEMU_STEPS	18
#define	RTL8192E_TRANS_ACT_TO_LPS_STEPS		23
#define	RTL8192E_TRANS_LPS_TO_ACT_STEPS		23
#define	RTL8192E_TRANS_END_STEPS		1

#define RTL8192E_TRANS_CARDEMU_TO_ACT					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/* disable HWPDN 0x04[15]=0*/					\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), 0},			\
	/* disable SW LPS 0x04[10]=0*/					\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), 0},			\
	/* disable WL suspend*/						\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0},		\
	/* wait till 0x04[17] = 1    power ready*/			\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(1), BIT(1)},		\
	/* release WLON reset  0x04[16]=1*/				\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), BIT(0)},		\
	/* polling until return 0*/					\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), BIT(0)},		\
	/**/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(0), 0},

#define RTL8192E_TRANS_ACT_TO_CARDEMU					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/*0x1F[7:0] = 0 turn off RF*/					\
	{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0},			\
	/*0x4C[23]=0x4E[7]=0, switch DPDT_SEL_P output from register 0x65[2] */\
	{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), 0},			\
	/*0x04[9] = 1 turn off MAC by HW state machine*/		\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), BIT(1)},		\
	/*wait till 0x04[9] = 0 polling until return 0 to disable*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(1), 0},

#define RTL8192E_TRANS_CARDEMU_TO_SUS					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/		\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(4) | BIT(3), (BIT(4) | BIT(3))},\
	/*0x04[12:11] = 2b'01 enable WL suspend*/			\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK,			\
	 PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC,	\
	 PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)},				\
	/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/		\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3) | BIT(4)},\
	/*Set SDIO suspend local register*/				\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), BIT(0)},		\
	 /*wait power state to suspend*/				\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), 0},

#define RTL8192E_TRANS_SUS_TO_CARDEMU					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/*Set SDIO suspend local register*/				\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), 0},			\
	/*wait power state to suspend*/					\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), BIT(1)},		\
	/*0x04[12:11] = 2b'00 disable WL suspend*/			\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(3) | BIT(4), 0},

#define RTL8192E_TRANS_CARDEMU_TO_CARDDIS				\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/*0x07=0x20 , SOP option to disable BG/MB*/			\
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x20},			\
	/*Unlock small LDO Register*/					\
	{0x00CC, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), BIT(2)},		\
	/*Disable small LDO*/						\
	{0x0011, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), 0},			\
	/*0x04[12:11] = 2b'01 enable WL suspend*/			\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK,			\
	 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC,		\
	 PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)},				\
	/*0x04[10] = 1, enable SW LPS*/					\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), BIT(2)},		\
	/*Set SDIO suspend local register*/				\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), BIT(0)},		\
	/*wait power state to suspend*/					\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), 0},

#define RTL8192E_TRANS_CARDDIS_TO_CARDEMU				\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/*Set SDIO suspend local register*/				\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), 0},			\
	/*wait power state to suspend*/					\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), BIT(1)},		\
	/*Enable small LDO*/						\
	{0x0011, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), BIT(0)},		\
	/*Lock small LDO Register*/					\
	{0x00CC, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), 0},			\
	/*0x04[12:11] = 2b'00 disable WL suspend*/			\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(3) | BIT(4), 0},

#define RTL8192E_TRANS_CARDEMU_TO_PDN					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/* 0x04[16] = 0*/						\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), 0},			\
	/* 0x04[15] = 1*/						\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), BIT(7)},

#define RTL8192E_TRANS_PDN_TO_CARDEMU					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/* 0x04[15] = 0*/						\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), 0},

#define RTL8192E_TRANS_ACT_TO_LPS					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/*PCIe DMA stop*/						\
	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF},			\
	/*Tx Pause*/							\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF},			\
	/*Should be zero if no packet is transmitting*/			\
	{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0},			\
	/*Should be zero if no packet is transmitting*/			\
	{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0},			\
	/*Should be zero if no packet is transmitting*/			\
	{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0},			\
	/*Should be zero if no packet is transmitting*/			\
	{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0},			\
	/*CCK and OFDM are disabled,and clock are gated*/		\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), 0},			\
	/*Delay 1us*/							\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},		\
	/*Whole BB is reset*/						\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), 0},			\
	/*Reset MAC TRX*/						\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x03},			\
	/*check if removed later*/					\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), 0},			\
	/*When driver enter Sus/ Disable, enable LOP for BT*/		\
	{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x00},			\
	/*Respond TxOK to scheduler*/					\
	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(5), BIT(5)},

#define RTL8192E_TRANS_LPS_TO_ACT					\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	/*SDIO RPWM, For Repeatly In and out, Taggle bit should be changed*/\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,	\
	 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, 0xFF, 0x84},		\
	/*USB RPWM*/							\
	{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x84},			\
	/*PCIe RPWM*/							\
	{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x84},			\
	/*Delay*/							\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS},		\
	/*0x08[4] = 0 switch TSF to 40M*/				\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(4), 0},			\
	/*Polling 0x109[7]=0  TSF in 40M*/				\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(7), 0},		\
	/*0x101[1] = 1*/						\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), BIT(1)},		\
	/*0x100[7:0] = 0xFF  enable WMAC TRX*/				\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF},			\
	/* 0x02[1:0] = 2b'11 enable BB macro*/				\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1) | BIT(0), BIT(1) | BIT(0)},\
	/*0x522 = 0*/							\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0},			\
	/*Clear ISR*/							\
	{0x013D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF},

#define RTL8192E_TRANS_END						\
	/* format */							\
	/* comments here */						\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
	{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,	\
	 0, PWR_CMD_END, 0, 0},

extern struct wlan_pwr_cfg rtl8192E_power_on_flow
					[RTL8192E_TRANS_CARDEMU_TO_ACT_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_radio_off_flow
					[RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_card_disable_flow
					[RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
					 RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_card_enable_flow
					[RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
					 RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_suspend_flow
					[RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
					 RTL8192E_TRANS_CARDEMU_TO_SUS_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_resume_flow
					[RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
					 RTL8192E_TRANS_CARDEMU_TO_SUS_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_hwpdn_flow
					[RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
					 RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_enter_lps_flow
					[RTL8192E_TRANS_ACT_TO_LPS_STEPS +
					 RTL8192E_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8192E_leave_lps_flow
					[RTL8192E_TRANS_LPS_TO_ACT_STEPS +
					 RTL8192E_TRANS_END_STEPS];

/* RTL8192EE Power Configuration CMDs for PCIe interface */
#define RTL8192E_NIC_PWR_ON_FLOW	rtl8192E_power_on_flow
#define RTL8192E_NIC_RF_OFF_FLOW	rtl8192E_radio_off_flow
#define RTL8192E_NIC_DISABLE_FLOW	rtl8192E_card_disable_flow
#define RTL8192E_NIC_ENABLE_FLOW	rtl8192E_card_enable_flow
#define RTL8192E_NIC_SUSPEND_FLOW	rtl8192E_suspend_flow
#define RTL8192E_NIC_RESUME_FLOW	rtl8192E_resume_flow
#define RTL8192E_NIC_PDN_FLOW		rtl8192E_hwpdn_flow
#define RTL8192E_NIC_LPS_ENTER_FLOW	rtl8192E_enter_lps_flow
#define RTL8192E_NIC_LPS_LEAVE_FLOW	rtl8192E_leave_lps_flow

#endif