1*4882a593Smuzhiyun# SPDX-License-Identifier: GPL-2.0-only 2*4882a593Smuzhiyun# 3*4882a593Smuzhiyun# Qualcomm network device configuration 4*4882a593Smuzhiyun# 5*4882a593Smuzhiyun 6*4882a593Smuzhiyunconfig NET_VENDOR_QUALCOMM 7*4882a593Smuzhiyun bool "Qualcomm devices" 8*4882a593Smuzhiyun default y 9*4882a593Smuzhiyun help 10*4882a593Smuzhiyun If you have a network (Ethernet) card belonging to this class, say Y. 11*4882a593Smuzhiyun 12*4882a593Smuzhiyun Note that the answer to this question doesn't directly affect the 13*4882a593Smuzhiyun kernel: saying N will just cause the configurator to skip all 14*4882a593Smuzhiyun the questions about Qualcomm cards. If you say Y, you will be asked 15*4882a593Smuzhiyun for your specific card in the following questions. 16*4882a593Smuzhiyun 17*4882a593Smuzhiyunif NET_VENDOR_QUALCOMM 18*4882a593Smuzhiyun 19*4882a593Smuzhiyunconfig QCA7000 20*4882a593Smuzhiyun tristate 21*4882a593Smuzhiyun help 22*4882a593Smuzhiyun This enables support for the Qualcomm Atheros QCA7000. 23*4882a593Smuzhiyun 24*4882a593Smuzhiyunconfig QCA7000_SPI 25*4882a593Smuzhiyun tristate "Qualcomm Atheros QCA7000 SPI support" 26*4882a593Smuzhiyun select QCA7000 27*4882a593Smuzhiyun depends on SPI_MASTER && OF 28*4882a593Smuzhiyun help 29*4882a593Smuzhiyun This SPI protocol driver supports the Qualcomm Atheros QCA7000. 30*4882a593Smuzhiyun 31*4882a593Smuzhiyun To compile this driver as a module, choose M here. The module 32*4882a593Smuzhiyun will be called qcaspi. 33*4882a593Smuzhiyun 34*4882a593Smuzhiyunconfig QCA7000_UART 35*4882a593Smuzhiyun tristate "Qualcomm Atheros QCA7000 UART support" 36*4882a593Smuzhiyun select QCA7000 37*4882a593Smuzhiyun depends on SERIAL_DEV_BUS && OF 38*4882a593Smuzhiyun help 39*4882a593Smuzhiyun This UART protocol driver supports the Qualcomm Atheros QCA7000. 40*4882a593Smuzhiyun 41*4882a593Smuzhiyun Currently the driver assumes these device UART settings: 42*4882a593Smuzhiyun Data bits: 8 43*4882a593Smuzhiyun Parity: None 44*4882a593Smuzhiyun Stop bits: 1 45*4882a593Smuzhiyun Flow control: None 46*4882a593Smuzhiyun 47*4882a593Smuzhiyun To compile this driver as a module, choose M here. The module 48*4882a593Smuzhiyun will be called qcauart. 49*4882a593Smuzhiyun 50*4882a593Smuzhiyunconfig QCOM_EMAC 51*4882a593Smuzhiyun tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support" 52*4882a593Smuzhiyun depends on HAS_DMA && HAS_IOMEM 53*4882a593Smuzhiyun select CRC32 54*4882a593Smuzhiyun select PHYLIB 55*4882a593Smuzhiyun help 56*4882a593Smuzhiyun This driver supports the Qualcomm Technologies, Inc. Gigabit 57*4882a593Smuzhiyun Ethernet Media Access Controller (EMAC). The controller 58*4882a593Smuzhiyun supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s, 59*4882a593Smuzhiyun full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for 60*4882a593Smuzhiyun low power, Receive-Side Scaling (RSS), and IEEE 1588-2008 61*4882a593Smuzhiyun Precision Clock Synchronization Protocol. 62*4882a593Smuzhiyun 63*4882a593Smuzhiyunsource "drivers/net/ethernet/qualcomm/rmnet/Kconfig" 64*4882a593Smuzhiyun 65*4882a593Smuzhiyunendif # NET_VENDOR_QUALCOMM 66