xref: /OK3568_Linux_fs/kernel/arch/arm/boot/dts/qcom-ipq8064.dtsi (revision 4882a59341e53eb6f0b4789bf948001014eff981)

// SPDX-License-Identifier: GPL-2.0
/dts-v1/;

#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>

/ {
	#address-cells = <1>;
	#size-cells = <1>;
	model = "Qualcomm IPQ8064";
	compatible = "qcom,ipq8064";
	interrupt-parent = <&intc>;

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu@0 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <0>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc0>;
			qcom,saw = <&saw0>;
		};

		cpu@1 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <1>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc1>;
			qcom,saw = <&saw1>;
		};

		L2: l2-cache {
			compatible = "cache";
			cache-level = <2>;
		};
	};

	memory {
		device_type = "memory";
		reg = <0x0 0x0>;
	};

	cpu-pmu {
		compatible = "qcom,krait-pmu";
		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
					  IRQ_TYPE_LEVEL_HIGH)>;
	};

	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		nss@40000000 {
			reg = <0x40000000 0x1000000>;
			no-map;
		};

		smem@41000000 {
			reg = <0x41000000 0x200000>;
			no-map;
		};
	};

	clocks {
		cxo_board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <25000000>;
		};

		pxo_board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <25000000>;
		};

		sleep_clk: sleep_clk {
			compatible = "fixed-clock";
			clock-frequency = <32768>;
			#clock-cells = <0>;
		};
	};

	firmware {
		scm {
			compatible = "qcom,scm-ipq806x", "qcom,scm";
		};
	};

	soc: soc {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;
		compatible = "simple-bus";

		lpass@28100000 {
			compatible = "qcom,lpass-cpu";
			status = "disabled";
			clocks = <&lcc AHBIX_CLK>,
					<&lcc MI2S_OSR_CLK>,
					<&lcc MI2S_BIT_CLK>;
			clock-names = "ahbix-clk",
					"mi2s-osr-clk",
					"mi2s-bit-clk";
			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "lpass-irq-lpaif";
			reg = <0x28100000 0x10000>;
			reg-names = "lpass-lpaif";
		};

		qcom_pinmux: pinmux@800000 {
			compatible = "qcom,ipq8064-pinctrl";
			reg = <0x800000 0x4000>;

			gpio-controller;
			gpio-ranges = <&qcom_pinmux 0 0 69>;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;

			pcie0_pins: pcie0_pinmux {
				mux {
					pins = "gpio3";
					function = "pcie1_rst";
					drive-strength = <12>;
					bias-disable;
				};
			};

			pcie1_pins: pcie1_pinmux {
				mux {
					pins = "gpio48";
					function = "pcie2_rst";
					drive-strength = <12>;
					bias-disable;
				};
			};

			pcie2_pins: pcie2_pinmux {
				mux {
					pins = "gpio63";
					function = "pcie3_rst";
					drive-strength = <12>;
					bias-disable;
				};
			};

			spi_pins: spi_pins {
				mux {
					pins = "gpio18", "gpio19", "gpio21";
					function = "gsbi5";
					drive-strength = <10>;
					bias-none;
				};
			};

			leds_pins: leds_pins {
				mux {
					pins = "gpio7", "gpio8", "gpio9",
					       "gpio26", "gpio53";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
					output-low;
				};
			};

			buttons_pins: buttons_pins {
				mux {
					pins = "gpio54";
					drive-strength = <2>;
					bias-pull-up;
				};
			};
		};

		intc: interrupt-controller@2000000 {
			compatible = "qcom,msm-qgic2";
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0x02000000 0x1000>,
			      <0x02002000 0x1000>;
		};

		timer@200a000 {
			compatible = "qcom,kpss-timer",
				     "qcom,kpss-wdt-ipq8064", "qcom,msm-timer";
			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
						 IRQ_TYPE_EDGE_RISING)>,
				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
						 IRQ_TYPE_EDGE_RISING)>,
				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
						 IRQ_TYPE_EDGE_RISING)>,
				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
						 IRQ_TYPE_EDGE_RISING)>,
				     <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
						 IRQ_TYPE_EDGE_RISING)>;
			reg = <0x0200a000 0x100>;
			clock-frequency = <25000000>,
					  <32768>;
			clocks = <&sleep_clk>;
			clock-names = "sleep";
			cpu-offset = <0x80000>;
		};

		acc0: clock-controller@2088000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
		};

		acc1: clock-controller@2098000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
		};

		saw0: regulator@2089000 {
			compatible = "qcom,saw2";
			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		saw1: regulator@2099000 {
			compatible = "qcom,saw2";
			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		gsbi2: gsbi@12480000 {
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <2>;
			reg = <0x12480000 0x100>;
			clocks = <&gcc GSBI2_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			status = "disabled";

			syscon-tcsr = <&tcsr>;

			serial@12490000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x12490000 0x1000>,
				      <0x12480000 0x1000>;
				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};

			i2c@124a0000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				reg = <0x124a0000 0x1000>;
				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;

				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;
			};

		};

		gsbi4: gsbi@16300000 {
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <4>;
			reg = <0x16300000 0x100>;
			clocks = <&gcc GSBI4_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			status = "disabled";

			syscon-tcsr = <&tcsr>;

			gsbi4_serial: serial@16340000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x16340000 0x1000>,
				      <0x16300000 0x1000>;
				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};

			i2c@16380000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				reg = <0x16380000 0x1000>;
				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;

				clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gsbi5: gsbi@1a200000 {
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <5>;
			reg = <0x1a200000 0x100>;
			clocks = <&gcc GSBI5_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			status = "disabled";

			syscon-tcsr = <&tcsr>;

			serial@1a240000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x1a240000 0x1000>,
				      <0x1a200000 0x1000>;
				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};

			i2c@1a280000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				reg = <0x1a280000 0x1000>;
				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;

				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;
			};

			spi@1a280000 {
				compatible = "qcom,spi-qup-v1.1.1";
				reg = <0x1a280000 0x1000>;
				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;

				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gsbi7: gsbi@16600000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <7>;
			reg = <0x16600000 0x100>;
			clocks = <&gcc GSBI7_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			syscon-tcsr = <&tcsr>;

			gsbi7_serial: serial@16640000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x16640000 0x1000>,
				      <0x16600000 0x1000>;
				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};
		};

		sata_phy: sata-phy@1b400000 {
			compatible = "qcom,ipq806x-sata-phy";
			reg = <0x1b400000 0x200>;

			clocks = <&gcc SATA_PHY_CFG_CLK>;
			clock-names = "cfg";

			#phy-cells = <0>;
			status = "disabled";
		};

		sata@29000000 {
			compatible = "qcom,ipq806x-ahci", "generic-ahci";
			reg = <0x29000000 0x180>;

			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc SFAB_SATA_S_H_CLK>,
				 <&gcc SATA_H_CLK>,
				 <&gcc SATA_A_CLK>,
				 <&gcc SATA_RXOOB_CLK>,
				 <&gcc SATA_PMALIVE_CLK>;
			clock-names = "slave_face", "iface", "core",
					"rxoob", "pmalive";

			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
			assigned-clock-rates = <100000000>, <100000000>;

			phys = <&sata_phy>;
			phy-names = "sata-phy";
			status = "disabled";
		};

		qcom,ssbi@500000 {
			compatible = "qcom,ssbi";
			reg = <0x00500000 0x1000>;
			qcom,controller-type = "pmic-arbiter";
		};

		qfprom: qfprom@700000 {
			compatible = "qcom,qfprom";
			reg = <0x00700000 0x1000>;
			#address-cells = <1>;
			#size-cells = <1>;
		};

		gcc: clock-controller@900000 {
			compatible = "qcom,gcc-ipq8064";
			reg = <0x00900000 0x4000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		tcsr: syscon@1a400000 {
			compatible = "qcom,tcsr-ipq8064", "syscon";
			reg = <0x1a400000 0x100>;
		};

		lcc: clock-controller@28000000 {
			compatible = "qcom,lcc-ipq8064";
			reg = <0x28000000 0x1000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		pcie0: pci@1b500000 {
			compatible = "qcom,pcie-ipq8064";
			reg = <0x1b500000 0x1000
			       0x1b502000 0x80
			       0x1b600000 0x100
			       0x0ff00000 0x100000>;
			reg-names = "dbi", "elbi", "parf", "config";
			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;
			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000   /* downstream I/O */
				  0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */

			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc PCIE_A_CLK>,
				 <&gcc PCIE_H_CLK>,
				 <&gcc PCIE_PHY_CLK>,
				 <&gcc PCIE_AUX_CLK>,
				 <&gcc PCIE_ALT_REF_CLK>;
			clock-names = "core", "iface", "phy", "aux", "ref";

			assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
			assigned-clock-rates = <100000000>;

			resets = <&gcc PCIE_ACLK_RESET>,
				 <&gcc PCIE_HCLK_RESET>,
				 <&gcc PCIE_POR_RESET>,
				 <&gcc PCIE_PCI_RESET>,
				 <&gcc PCIE_PHY_RESET>,
				 <&gcc PCIE_EXT_RESET>;
			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";

			pinctrl-0 = <&pcie0_pins>;
			pinctrl-names = "default";

			status = "disabled";
			perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
		};

		pcie1: pci@1b700000 {
			compatible = "qcom,pcie-ipq8064";
			reg = <0x1b700000 0x1000
			       0x1b702000 0x80
			       0x1b800000 0x100
			       0x31f00000 0x100000>;
			reg-names = "dbi", "elbi", "parf", "config";
			device_type = "pci";
			linux,pci-domain = <1>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;
			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000   /* downstream I/O */
				  0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */

			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc PCIE_1_A_CLK>,
				 <&gcc PCIE_1_H_CLK>,
				 <&gcc PCIE_1_PHY_CLK>,
				 <&gcc PCIE_1_AUX_CLK>,
				 <&gcc PCIE_1_ALT_REF_CLK>;
			clock-names = "core", "iface", "phy", "aux", "ref";

			assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
			assigned-clock-rates = <100000000>;

			resets = <&gcc PCIE_1_ACLK_RESET>,
				 <&gcc PCIE_1_HCLK_RESET>,
				 <&gcc PCIE_1_POR_RESET>,
				 <&gcc PCIE_1_PCI_RESET>,
				 <&gcc PCIE_1_PHY_RESET>,
				 <&gcc PCIE_1_EXT_RESET>;
			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";

			pinctrl-0 = <&pcie1_pins>;
			pinctrl-names = "default";

			status = "disabled";
			perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
		};

		pcie2: pci@1b900000 {
			compatible = "qcom,pcie-ipq8064";
			reg = <0x1b900000 0x1000
			       0x1b902000 0x80
			       0x1ba00000 0x100
			       0x35f00000 0x100000>;
			reg-names = "dbi", "elbi", "parf", "config";
			device_type = "pci";
			linux,pci-domain = <2>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;
			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000   /* downstream I/O */
				  0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */

			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc PCIE_2_A_CLK>,
				 <&gcc PCIE_2_H_CLK>,
				 <&gcc PCIE_2_PHY_CLK>,
				 <&gcc PCIE_2_AUX_CLK>,
				 <&gcc PCIE_2_ALT_REF_CLK>;
			clock-names = "core", "iface", "phy", "aux", "ref";

			assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
			assigned-clock-rates = <100000000>;

			resets = <&gcc PCIE_2_ACLK_RESET>,
				 <&gcc PCIE_2_HCLK_RESET>,
				 <&gcc PCIE_2_POR_RESET>,
				 <&gcc PCIE_2_PCI_RESET>,
				 <&gcc PCIE_2_PHY_RESET>,
				 <&gcc PCIE_2_EXT_RESET>;
			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";

			pinctrl-0 = <&pcie2_pins>;
			pinctrl-names = "default";

			status = "disabled";
			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
		};

		nss_common: syscon@03000000 {
			compatible = "syscon";
			reg = <0x03000000 0x0000FFFF>;
		};

		qsgmii_csr: syscon@1bb00000 {
			compatible = "syscon";
			reg = <0x1bb00000 0x000001FF>;
		};

		stmmac_axi_setup: stmmac-axi-config {
			snps,wr_osr_lmt = <7>;
			snps,rd_osr_lmt = <7>;
			snps,blen = <16 0 0 0 0 0 0>;
		};

		gmac0: ethernet@37000000 {
			device_type = "network";
			compatible = "qcom,ipq806x-gmac";
			reg = <0x37000000 0x200000>;
			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "macirq";

			snps,axi-config = <&stmmac_axi_setup>;
			snps,pbl = <32>;
			snps,aal = <1>;

			qcom,nss-common = <&nss_common>;
			qcom,qsgmii-csr = <&qsgmii_csr>;

			clocks = <&gcc GMAC_CORE1_CLK>;
			clock-names = "stmmaceth";

			resets = <&gcc GMAC_CORE1_RESET>;
			reset-names = "stmmaceth";

			status = "disabled";
		};

		gmac1: ethernet@37200000 {
			device_type = "network";
			compatible = "qcom,ipq806x-gmac";
			reg = <0x37200000 0x200000>;
			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "macirq";

			snps,axi-config = <&stmmac_axi_setup>;
			snps,pbl = <32>;
			snps,aal = <1>;

			qcom,nss-common = <&nss_common>;
			qcom,qsgmii-csr = <&qsgmii_csr>;

			clocks = <&gcc GMAC_CORE2_CLK>;
			clock-names = "stmmaceth";

			resets = <&gcc GMAC_CORE2_RESET>;
			reset-names = "stmmaceth";

			status = "disabled";
		};

		gmac2: ethernet@37400000 {
			device_type = "network";
			compatible = "qcom,ipq806x-gmac";
			reg = <0x37400000 0x200000>;
			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "macirq";

			snps,axi-config = <&stmmac_axi_setup>;
			snps,pbl = <32>;
			snps,aal = <1>;

			qcom,nss-common = <&nss_common>;
			qcom,qsgmii-csr = <&qsgmii_csr>;

			clocks = <&gcc GMAC_CORE3_CLK>;
			clock-names = "stmmaceth";

			resets = <&gcc GMAC_CORE3_RESET>;
			reset-names = "stmmaceth";

			status = "disabled";
		};

		gmac3: ethernet@37600000 {
			device_type = "network";
			compatible = "qcom,ipq806x-gmac";
			reg = <0x37600000 0x200000>;
			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "macirq";

			snps,axi-config = <&stmmac_axi_setup>;
			snps,pbl = <32>;
			snps,aal = <1>;

			qcom,nss-common = <&nss_common>;
			qcom,qsgmii-csr = <&qsgmii_csr>;

			clocks = <&gcc GMAC_CORE4_CLK>;
			clock-names = "stmmaceth";

			resets = <&gcc GMAC_CORE4_RESET>;
			reset-names = "stmmaceth";

			status = "disabled";
		};

		vsdcc_fixed: vsdcc-regulator {
			compatible = "regulator-fixed";
			regulator-name = "SDCC Power";
			regulator-min-microvolt = <3300000>;
			regulator-max-microvolt = <3300000>;
			regulator-always-on;
		};

		sdcc1bam:dma@12402000 {
			compatible = "qcom,bam-v1.3.0";
			reg = <0x12402000 0x8000>;
			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc SDC1_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		sdcc3bam:dma@12182000 {
			compatible = "qcom,bam-v1.3.0";
			reg = <0x12182000 0x8000>;
			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc SDC3_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		amba {
			compatible = "simple-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			sdcc@12400000 {
				status          = "disabled";
				compatible      = "arm,pl18x", "arm,primecell";
				arm,primecell-periphid = <0x00051180>;
				reg             = <0x12400000 0x2000>;
				interrupts      = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "cmd_irq";
				clocks          = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
				clock-names     = "mclk", "apb_pclk";
				bus-width       = <8>;
				max-frequency   = <96000000>;
				non-removable;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				mmc-ddr-1_8v;
				vmmc-supply = <&vsdcc_fixed>;
				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
				dma-names = "tx", "rx";
			};

			sdcc@12180000 {
				compatible      = "arm,pl18x", "arm,primecell";
				arm,primecell-periphid = <0x00051180>;
				status          = "disabled";
				reg             = <0x12180000 0x2000>;
				interrupts      = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "cmd_irq";
				clocks          = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
				clock-names     = "mclk", "apb_pclk";
				bus-width       = <8>;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				max-frequency   = <192000000>;
				#mmc-ddr-1_8v;
				sd-uhs-sdr104;
				sd-uhs-ddr50;
				vqmmc-supply = <&vsdcc_fixed>;
				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
				dma-names = "tx", "rx";
			};
		};
	};
};