xref: /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt (revision 4882a59341e53eb6f0b4789bf948001014eff981)

Qualcomm SM8150 TLMM block

This binding describes the Top Level Mode Multiplexer block found in the
QCS404 platform.

- compatible:
	Usage: required
	Value type: <string>
	Definition: must be "qcom,sm8150-pinctrl"

- reg:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: the base address and size of the north, south, west
		    and east TLMM tiles.

- reg-names:
	Usage: required
	Value type: <prop-encoded-array>
	Defintiion: names for the cells of reg, must contain "north", "south"
		    "west" and "east".

- interrupts:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: should specify the TLMM summary IRQ.

- interrupt-controller:
	Usage: required
	Value type: <none>
	Definition: identifies this node as an interrupt controller

- #interrupt-cells:
	Usage: required
	Value type: <u32>
	Definition: must be 2. Specifying the pin number and flags, as defined
		    in <dt-bindings/interrupt-controller/irq.h>

- gpio-controller:
	Usage: required
	Value type: <none>
	Definition: identifies this node as a gpio controller

- #gpio-cells:
	Usage: required
	Value type: <u32>
	Definition: must be 2. Specifying the pin number and flags, as defined
		    in <dt-bindings/gpio/gpio.h>

- gpio-ranges:
	Usage: required
	Value type: <prop-encoded-array>
	Definition:  see ../gpio/gpio.txt

- gpio-reserved-ranges:
	Usage: optional
	Value type: <prop-encoded-array>
	Definition: see ../gpio/gpio.txt

Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.

Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".

The pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin, a group, or a list of pins or groups. This configuration can include the
mux function to select on those pin(s)/group(s), and various pin configuration
parameters, such as pull-up, drive strength, etc.


PIN CONFIGURATION NODES:

The name of each subnode is not important; all subnodes should be enumerated
and processed purely based on their content.

Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.


The following generic properties as defined in pinctrl-bindings.txt are valid
to specify in a pin configuration subnode:

- pins:
	Usage: required
	Value type: <string-array>
	Definition: List of gpio pins affected by the properties specified in
		    this subnode.

		    Valid pins are:
		      gpio0-gpio149
		        Supports mux, bias and drive-strength

		      sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,
		      sdc2_data sdc1_rclk
		        Supports bias and drive-strength

		      ufs_reset
		        Supports bias and drive-strength

- function:
	Usage: required
	Value type: <string>
	Definition: Specify the alternative function to be configured for the
		    specified pins. Functions are only valid for gpio pins.
		    Valid values are:

		    adsp_ext, agera_pll, aoss_cti, ddr_pxi2, atest_char,
		    atest_char0, atest_char1, atest_char2, atest_char3,
		    audio_ref, atest_usb1, atest_usb2, atest_usb10,
		    atest_usb11, atest_usb12, atest_usb13, atest_usb20,
		    atest_usb21, atest_usb22, atest_usb2, atest_usb23,
		    btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
		    cci_timer1, cci_timer2, cci_timer3, cci_timer4,
		    cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
		    ddr_pxi0, ddr_pxi1, ddr_pxi3, edp_hot, edp_lcd,
		    emac_phy, emac_pps, gcc_gp1, gcc_gp2, gcc_gp3, gpio,
		    hs1_mi2s, hs2_mi2s, hs3_mi2s, jitter_bist,
		    lpass_slimbus, mdp_vsync, mdp_vsync0, mdp_vsync1,
		    mdp_vsync2, mdp_vsync3, mss_lte, m_voc, nav_pps,
		    pa_indicator, pci_e0, phase_flag, pll_bypassnl,
		    pll_bist, pci_e1, pll_reset, pri_mi2s, pri_mi2s_ws,
		    prng_rosc, qdss, qdss_cti, qlink_request, qlink_enable,
		    qspi0, qspi1, qspi2, qspi3, qspi_clk, qspi_cs, qua_mi2s,
		    qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8,
		    qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16,
		    qup17, qup18, qup19, qup_l4, qup_l5, qup_l6, rgmii,
		    sdc4, sd_write, sec_mi2s, spkr_i2s, sp_cmu, ter_mi2s,
		    tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1,
		    tsense_pwm2, tsif1, tsif2, uim1, uim2, uim_batt,
		    usb2phy_ac, usb_phy, vfr_1, vsense_trigger, wlan1_adc0,
		    wlan1_adc1, wlan2_adc0, wlan2_adc1, wmss_reset

- bias-disable:
	Usage: optional
	Value type: <none>
	Definition: The specified pins should be configued as no pull.

- bias-pull-down:
	Usage: optional
	Value type: <none>
	Definition: The specified pins should be configued as pull down.

- bias-pull-up:
	Usage: optional
	Value type: <none>
	Definition: The specified pins should be configued as pull up.

- output-high:
	Usage: optional
	Value type: <none>
	Definition: The specified pins are configured in output mode, driven
		    high.
		    Not valid for sdc pins.

- output-low:
	Usage: optional
	Value type: <none>
	Definition: The specified pins are configured in output mode, driven
		    low.
		    Not valid for sdc pins.

- drive-strength:
	Usage: optional
	Value type: <u32>
	Definition: Selects the drive strength for the specified pins, in mA.
		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16

Example:

	tlmm: pinctrl@3000000 {
		compatible = "qcom,sm8150-pinctrl";
		reg = <0x03100000 0x300000>,
		      <0x03500000 0x300000>,
		      <0x03900000 0x300000>,
		      <0x03D00000 0x300000>;
		reg-names = "west", "east", "north", "south";
		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
		gpio-controller;
		#gpio-cells = <2>;
		gpio-ranges = <&tlmm 0 0 175>;
		gpio-reserved-ranges = <0 4>, <126 4>;
		interrupt-controller;
		#interrupt-cells = <2>;
	};