1 /****************************************************************************** 2 * 3 * Copyright(c) 2007 - 2017 Realtek Corporation. 4 * 5 * This program is free software; you can redistribute it and/or modify it 6 * under the terms of version 2 of the GNU General Public License as 7 * published by the Free Software Foundation. 8 * 9 * This program is distributed in the hope that it will be useful, but WITHOUT 10 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 11 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 12 * more details. 13 * 14 *****************************************************************************/ 15 16 17 #ifndef __HAL8188EPWRSEQ_H__ 18 #define __HAL8188EPWRSEQ_H__ 19 20 #include "HalPwrSeqCmd.h" 21 22 /* 23 Check document WM-20110607-Paul-RTL8188E_Power_Architecture-R02.vsd 24 There are 6 HW Power States: 25 0: POFF--Power Off 26 1: PDN--Power Down 27 2: CARDEMU--Card Emulation 28 3: ACT--Active Mode 29 4: LPS--Low Power State 30 5: SUS--Suspend 31 32 The transision from different states are defined below 33 TRANS_CARDEMU_TO_ACT 34 TRANS_ACT_TO_CARDEMU 35 TRANS_CARDEMU_TO_SUS 36 TRANS_SUS_TO_CARDEMU 37 TRANS_CARDEMU_TO_PDN 38 TRANS_ACT_TO_LPS 39 TRANS_LPS_TO_ACT 40 41 TRANS_END 42 43 PWR SEQ Version: rtl8188E_PwrSeq_V09.h 44 */ 45 #define RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS 10 46 #define RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS 10 47 #define RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS 10 48 #define RTL8188E_TRANS_SUS_TO_CARDEMU_STEPS 10 49 #define RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS 10 50 #define RTL8188E_TRANS_PDN_TO_CARDEMU_STEPS 10 51 #define RTL8188E_TRANS_ACT_TO_LPS_STEPS 15 52 #define RTL8188E_TRANS_LPS_TO_ACT_STEPS 15 53 #define RTL8188E_TRANS_END_STEPS 1 54 55 56 #define RTL8188E_TRANS_CARDEMU_TO_ACT \ 57 /* format */ \ 58 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 59 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \ 60 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 | BIT1, 0}, /* 0x02[1:0] = 0 reset BB*/ \ 61 {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7}, /*0x24[23] = 2b'01 schmit trigger */ \ 62 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0}, /* 0x04[15] = 0 disable HWPDN (control by DRV)*/\ 63 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4 | BIT3, 0}, /*0x04[12:11] = 2b'00 disable WL suspend*/ \ 64 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*0x04[8] = 1 polling until return 0*/ \ 65 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0}, /*wait till 0x04[8] = 0*/ \ 66 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*LDO normal mode*/ \ 67 68 #define RTL8188E_TRANS_ACT_TO_CARDEMU \ 69 /* format */ \ 70 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 71 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \ 72 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*LDO Sleep mode*/ \ 73 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \ 74 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \ 75 76 #define RTL8188E_TRANS_CARDEMU_TO_SUS \ 77 /* format */ \ 78 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 79 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01enable WL suspend*/ \ 80 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3 | BIT4}, /*0x04[12:11] = 2b'11enable WL suspend for PCIe*/ \ 81 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, BIT7}, /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */ \ 82 {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*Clear SIC_EN register 0x40[12] = 1'b0 */ \ 83 {0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*Set USB suspend enable local register 0xfe10[4]=1 */ \ 84 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ 85 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ 86 87 #define RTL8188E_TRANS_SUS_TO_CARDEMU \ 88 /* format */ \ 89 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 90 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ 91 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ 92 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ 93 94 #define RTL8188E_TRANS_CARDEMU_TO_CARDDIS \ 95 /* format */ \ 96 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 97 {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7}, /*0x24[23] = 2b'01 schmit trigger */ \ 98 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ 99 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */ \ 100 {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*Clear SIC_EN register 0x40[12] = 1'b0 */ \ 101 {0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*Set USB suspend enable local register 0xfe10[4]=1 */ \ 102 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ 103 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ 104 105 #define RTL8188E_TRANS_CARDDIS_TO_CARDEMU \ 106 /* format */ \ 107 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 108 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ 109 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ 110 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ 111 112 #define RTL8188E_TRANS_CARDEMU_TO_PDN \ 113 /* format */ \ 114 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 115 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\ 116 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/ 117 118 #define RTL8188E_TRANS_PDN_TO_CARDEMU \ 119 /* format */ \ 120 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 121 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/ 122 123 /* This is used by driver for LPSRadioOff Procedure, not for FW LPS Step */ 124 #define RTL8188E_TRANS_ACT_TO_LPS \ 125 /* format */ \ 126 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 127 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \ 128 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 129 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 130 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 131 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 132 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \ 133 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ 134 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \ 135 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \ 136 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \ 137 138 139 #define RTL8188E_TRANS_LPS_TO_ACT \ 140 /* format */ \ 141 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 142 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\ 143 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\ 144 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\ 145 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ 146 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\ 147 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0 TSF in 40M*/\ 148 {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6 | BIT7, 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\ 149 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/\ 150 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ 151 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1 | BIT0, BIT1 | BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\ 152 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ 153 154 #define RTL8188E_TRANS_END \ 155 /* format */ \ 156 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 157 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0}, 158 159 160 extern WLAN_PWR_CFG rtl8188E_power_on_flow[RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS]; 161 extern WLAN_PWR_CFG rtl8188E_radio_off_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_END_STEPS]; 162 extern WLAN_PWR_CFG rtl8188E_card_disable_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS]; 163 extern WLAN_PWR_CFG rtl8188E_card_enable_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS]; 164 extern WLAN_PWR_CFG rtl8188E_suspend_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188E_TRANS_END_STEPS]; 165 extern WLAN_PWR_CFG rtl8188E_resume_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188E_TRANS_END_STEPS]; 166 extern WLAN_PWR_CFG rtl8188E_hwpdn_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS]; 167 extern WLAN_PWR_CFG rtl8188E_enter_lps_flow[RTL8188E_TRANS_ACT_TO_LPS_STEPS + RTL8188E_TRANS_END_STEPS]; 168 extern WLAN_PWR_CFG rtl8188E_leave_lps_flow[RTL8188E_TRANS_LPS_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS]; 169 170 #endif /* __HAL8188EPWRSEQ_H__ */ 171