1*4882a593Smuzhiyun 2*4882a593SmuzhiyunIntel Galileo Gen 1/2 3*4882a593Smuzhiyun 4*4882a593SmuzhiyunIntro 5*4882a593Smuzhiyun============ 6*4882a593Smuzhiyun 7*4882a593SmuzhiyunThese instructions apply to both the Intel Galileo Gen 1/2 development boards 8*4882a593Smuzhiyunbased on the Intel Quark X1000. 9*4882a593Smuzhiyun 10*4882a593SmuzhiyunHow to build 11*4882a593Smuzhiyun============ 12*4882a593Smuzhiyun 13*4882a593SmuzhiyunApply the defconfig for the Intel Galileo Gen 1/2 14*4882a593Smuzhiyun 15*4882a593Smuzhiyun $ make galileo_defconfig 16*4882a593Smuzhiyun 17*4882a593SmuzhiyunAdd any additional packages required and build. 18*4882a593Smuzhiyun 19*4882a593Smuzhiyun $ make 20*4882a593Smuzhiyun 21*4882a593SmuzhiyunThe build process will create a SD card image and place it in output/images. 22*4882a593Smuzhiyun 23*4882a593Smuzhiyun $ ls -lh output/images/sdcard.img 24*4882a593Smuzhiyun -rw-r--r--. 1 foo foo 11M Nov 17 16:19 output/images/sdcard.img 25*4882a593Smuzhiyun 26*4882a593SmuzhiyunWrite the image to an mSD card, insert into the Galileo and power on. 27*4882a593Smuzhiyun 28*4882a593Smuzhiyun $ dd if=output/images/sdcard.img of=/dev/mmcblk0; sync 29*4882a593Smuzhiyun 30*4882a593SmuzhiyunAccessing the console 31*4882a593Smuzhiyun===================== 32*4882a593Smuzhiyun 33*4882a593SmuzhiyunDuring power-on the console will become available on the Galileo's ttyS1. This 34*4882a593Smuzhiyunmay be accessed as follows. 35*4882a593Smuzhiyun 36*4882a593Smuzhiyun * Galileo Gen 1 37*4882a593Smuzhiyun 38*4882a593Smuzhiyun http://clayskits.com/products/galileo-gen-1-serial-cable 39*4882a593Smuzhiyun 40*4882a593Smuzhiyun A USB to RS-232 to 3.5mm Jack cable is required. Connect to the 3.5mm 41*4882a593Smuzhiyun Jack next to the Ethernet Header. 42*4882a593Smuzhiyun 43*4882a593Smuzhiyun * Galileo Gen 2 44*4882a593Smuzhiyun 45*4882a593Smuzhiyun http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm 46*4882a593Smuzhiyun 47*4882a593Smuzhiyun A FTDI TTL-232R-3V3 cable may be used to connect to the FTDI header 48*4882a593Smuzhiyun next to the Ethernet connector on the Galileo Gen 2. 49*4882a593Smuzhiyun 50*4882a593SmuzhiyunThe console should now be visible at 115200 baud. 51*4882a593Smuzhiyun 52*4882a593Smuzhiyun $ picocom -b 115200 /dev/ttyUSB0 53