Home
last modified time | relevance | path

Searched refs:variables (Results 1 – 25 of 72) sorted by relevance

123

/rk3399_rockchip-uboot/doc/
H A DREADME.at9118 Environment variables
20 U-Boot environment variables can be stored at different places:
40 Environment variables
42 U-Boot environment variables can be stored at different places:
61 Environment variables
63 U-Boot environment variables can be stored at different places:
84 Environment variables
86 U-Boot environment variables can be stored at different places:
101 Environment variables
103 U-Boot environment variables can be stored at different places:
[all …]
H A DREADME.spear36 spear320 build with environment variables placed at default
40 for CFI compliant parallel NOR flash. Environment variables are
43 spear320 build with environment variables placed in NAND device
73 environment variables. Although, we can check the mac id programmed in i2c
H A DREADME.dfutftp54 Environment variables
66 1. Setup tftp env variables:
69 * setup "serverip" and "ipaddr" variables
82 2. Setup update_tftp variables:
89 4. Inspect "dfu" specific variables:
H A DREADME.link-local27 The "ipaddr", "netmask", and "gatewayip" variables are set
50 by env variables. It depends on CONFIG_CMD_LINK_LOCAL, CONFIG_CMD_DHCP,
H A DREADME.SNTP12 don't need to set the above environment variables yourself.
H A DREADME.m54418twr230 printenv- print environment variables
234 saveenv - save environment variables to persistent storage
235 setenv - set environment variables
237 showvar - print local hushshell variables
H A DREADME.bootmenu21 The assembling of the menu is done via a set of environment variables
51 entries specified by environment variables. When selecting this entry
H A DREADME.distro196 environment variables a generic boot.scr may rely upon.
206 variables be set. Default values for these variables are often hard-coded into
275 <config_distro_bootcmd.h> defines $bootcmd and many helper command variables
307 up by <config_distro_bootcmd.h>. After this, various environment variables may
370 prompt, the environment provides predefined bootcmd_<target> variables for
405 Other *boot* variables than the ones defined above are only for internal use
408 variables (e.g. mmc_boot, usb_boot) are a strictly internal implementation
H A DREADME.pxe24 'pxe get' requires two environment variables to be set:
35 'pxe get' optionally supports these two environment variables being set:
65 There are some environment variables that may need to be set, depending
83 environment variables are required to be set.
162 variables, i.e. <path>/<soc>-<board>.dtb is retrieved.
H A DREADME.vxworks54 environments variables: bootdev, bootfile, ipaddr, netmask, serverip,
70 Before loading an x86 kernel, two additional environment variables need to be
H A DREADME.NetConsole5 'stdout' environment variables. To switch to the networked console,
6 set either of these variables to "nc". Input and output can be
H A DREADME.nokia_rx5145 Available additional commands/variables:
67 Additional variables for loading files from mmc:
H A DREADME.enetaddr59 contain these environment variables, i.e. existing variable definitions must
62 During runtime, the ethernet layer will use the environment variables to sync
H A DREADME.falcon84 Environment variables
88 mode. In this case the following variables may be supported:
124 These environment variables can be used in scripts for writing updated
/rk3399_rockchip-uboot/board/keymile/scripts/
H A DREADME5 To load and configure these usecase, two environment variables in the u-boot
14 This file defines variables for working with rootfs via nfs for powerpc and
19 This file defines architecture specific variables for working with rootfs via
25 This file defines variables for working with rootfs inside the ram for powerpc
30 This file defines architecture specific variables for working with rootfs inside
/rk3399_rockchip-uboot/board/freescale/mx28evk/
H A DREADME40 "make mx28evk_config" - store environment variables into MMC
44 "make mx28evk_nand_config" - store environment variables into NAND flash
48 "make mx28evk_spi_config" - store environment variables into SPI NOR flash
/rk3399_rockchip-uboot/tools/kermit/
H A DREADME27 variables on your target. This is most useful during
28 development when your environment variables are stored in an
/rk3399_rockchip-uboot/board/freescale/mpc8323erdb/
H A DREADME47 To keep your old U-Boot's environment variables, do a:
55 Ensure that all networking-related environment variables are set
/rk3399_rockchip-uboot/board/technexion/pico-imx7d/
H A DREADME33 Use the default environment variables:
/rk3399_rockchip-uboot/common/
H A Dcli_hush.c272 struct variables { struct
277 struct variables *next; argument
305 struct variables shell_ver = { "HUSH_VERSION", "0.01", 1, 1, 0 };
306 struct variables *top_vars = &shell_ver;
310 static struct variables *top_vars = NULL ;
780 struct variables *e; in builtin_set()
2140 struct variables *cur;
2164 struct variables *cur;
2216 cur = malloc(sizeof(struct variables));
2225 struct variables *bottom = top_vars;
[all …]
/rk3399_rockchip-uboot/board/warp/
H A DREADME34 Use the default environment variables:
/rk3399_rockchip-uboot/board/technexion/pico-imx6ul/
H A DREADME35 Use the default environment variables:
/rk3399_rockchip-uboot/board/warp7/
H A DREADME41 Use the default environment variables:
/rk3399_rockchip-uboot/board/freescale/m52277evb/
H A DREADME221 printenv- print environment variables
225 saveenv - save environment variables to persistent storage
226 setenv - set environment variables
/rk3399_rockchip-uboot/board/freescale/m547xevb/
H A DREADME252 printenv- print environment variables
257 saveenv - save environment variables to persistent storage
258 setenv - set environment variables

123