| /rk3399_rockchip-uboot/doc/device-tree-bindings/clock/ |
| H A D | st,stm32-rcc.txt | 35 The secondary index is the bit number within the RCC register bank, starting
84 The index is the bit number within the RCC registers bank, starting from RCC
|
| /rk3399_rockchip-uboot/board/Barix/ipam390/ |
| H A D | ipam390-ais-uart.cfg | 58 ; for starting the DDR2 interface.
166 ; for starting the DDR2 interface on ARM-boot D800K002 devices.
183 ; for starting the DDR2 interface on DSP-boot D800K002 devices.
|
| /rk3399_rockchip-uboot/doc/ |
| H A D | README.ublimage | 38 2. This file can have empty lines and lines starting with "#" as first
122 starting with block 1 (page 0). When a valid UBL signature is found,
134 nand_spl into ARM internal RAM, starting at address 0x0000: 0020.
|
| H A D | README.arm-caches | 25 - Invalidate the buffer before starting the DMA. In case there are any dirty
|
| H A D | README.pblimage | 67 2. These files can have empty lines and lines starting with "#" as first
|
| H A D | README.unaligned-memory-access.txt | 16 Unaligned memory accesses occur when you try to read N bytes of data starting
88 starting at address 0x10000. With a basic level of understanding, it would
164 2 bytes (16 bits) to be read from memory starting at address addr1.
|
| H A D | README.menu | 17 If you want to show a menu, instead starting the shell, define
|
| H A D | README.kwbimage | 46 2. This file can have empty lines and lines starting with "#" as first
|
| H A D | README.odroid | 41 The block offset is starting from 0 and the block size is 512B.
165 The ethernet can be accessed after starting the USB subsystem in U-Boot.
167 to be set before starting USB.
|
| H A D | README.bootmenu | 30 <num> is the boot menu entry number, starting from zero
|
| H A D | README.gpt | 106 72 8 B Partition entries starting LBA (always 2 in primary copy)
201 When provided, additionally partition data - name, size and starting
|
| H A D | README.nokia_rx51 | 25 When U-Boot is starting it enable IBE bit in Auxiliary Control Register,
|
| H A D | README.mxc_hab | 57 An authenticated U-Boot image is used as starting point for
|
| H A D | README.android-fastboot-protocol | 168 Names starting with a lowercase character are reserved by this
|
| H A D | README.nand | 23 Erase `size' bytes starting at offset `off'. Alternatively partition
93 NAND Offset from where SPL will read u-boot image. This is the starting
|
| H A D | README.imximage | 46 2. This file can have empty lines and lines starting with "#" as first
|
| /rk3399_rockchip-uboot/board/freescale/mpc8610hpcd/ |
| H A D | README | 16 The flash is 128M starting at 0xF800_0000.
|
| /rk3399_rockchip-uboot/doc/SPI/ |
| H A D | README.sandbox-spi | 5 using the --spi_sf paramter when starting U-Boot.
|
| /rk3399_rockchip-uboot/board/lego/ev3/ |
| H A D | README | 18 flash and have a maximum size of 9.3MiB. The flash starting at 0xCB0000 is
|
| /rk3399_rockchip-uboot/board/boundary/nitrogen6x/ |
| H A D | README.mx6qsabrelite | 38 (the default one the board is shipped with, starting from the SPI NOR) and
|
| /rk3399_rockchip-uboot/cmd/fastboot/ |
| H A D | Kconfig | 48 downloads. Define this to the starting RAM address to use for
|
| /rk3399_rockchip-uboot/board/cobra5272/ |
| H A D | README | 89 => u-boot as single bootloader starting from flash
|
| /rk3399_rockchip-uboot/board/hisilicon/poplar/ |
| H A D | README | 159 starting USB...
274 starting USB...
|
| /rk3399_rockchip-uboot/board/davinci/da8xxevm/ |
| H A D | README.da850 | 79 conveniently have a bootloader partition starting at the second block
|
| /rk3399_rockchip-uboot/board/gateworks/gw_ventana/ |
| H A D | README | 132 # create a partition table with a single rootfs partition starting at 1MB
279 # create a partition table with a single rootfs partition starting at 10MB
|