| /rk3399_rockchip-uboot/scripts/kconfig/ |
| H A D | qconf.cc | 279 connect(this, SIGNAL(editingFinished()), SLOT(hide())); in ConfigLineEdit()
332 connect(this, SIGNAL(itemSelectionChanged(void)), in ConfigList()
342 connect(configApp, SIGNAL(aboutToQuit()), SLOT(saveSettings())); in ConfigList()
888 connect(action, SIGNAL(toggled(bool)), in contextMenuEvent()
890 connect(parent(), SIGNAL(showNameChanged(bool)), in contextMenuEvent()
896 connect(action, SIGNAL(toggled(bool)), in contextMenuEvent()
898 connect(parent(), SIGNAL(showRangeChanged(bool)), in contextMenuEvent()
904 connect(action, SIGNAL(toggled(bool)), in contextMenuEvent()
906 connect(parent(), SIGNAL(showDataChanged(bool)), in contextMenuEvent()
1027 connect(configApp, SIGNAL(aboutToQuit()), SLOT(saveSettings())); in ConfigInfoView()
[all …]
|
| /rk3399_rockchip-uboot/drivers/spmi/ |
| H A D | Kconfig | 9 to connect PMIC devices on various SoCs.
|
| /rk3399_rockchip-uboot/doc/ |
| H A D | README.440-DDR-performance | 42 ttcp-t: connect
82 ttcp-t: connect
|
| H A D | README.link-local | 42 This is also not a concern if the feature is use to connect
|
| H A D | README.arm-relocation | 129 b) connect to target
|
| H A D | README.ubi | 27 The first command that is needed to be issues is "ubi part" to connect
|
| H A D | README.usb | 82 independent network device, able to connect and perform network operations
|
| /rk3399_rockchip-uboot/board/freescale/mpc837xemds/ |
| H A D | README | 34 J10 removed, CS0 connect to NOR flash; when mounted, CS0 connect to NAND
|
| /rk3399_rockchip-uboot/drivers/usb/ |
| H A D | Kconfig | 12 Most PCs now have USB host ports, used to connect peripherals
87 Say Y here if you want to connect USB mass storage devices to your
|
| /rk3399_rockchip-uboot/doc/SPL/ |
| H A D | README.am335x-network | 38 chose to connect to the board (usually configured in
55 used to connect to the board is eth0, and it has address 192.168.8.1:
|
| /rk3399_rockchip-uboot/drivers/i2c/muxes/ |
| H A D | Kconfig | 34 paritioning I2C bus and connect multiple devices with the same address
|
| /rk3399_rockchip-uboot/arch/arm/dts/ |
| H A D | at91-sama5d4ek.dts | 88 /* The vref depends on JP22 of EK. If connect 1-2 then use 3.3V. connect 2-3 use 3.0V */
|
| H A D | rk3288.dtsi | 180 connect = <&vopb_out_hdmi>;
189 connect = <&vopl_out_edp>;
198 connect = <&vopl_out_dsi0>;
207 connect = <&vopl_out_lvds>;
|
| H A D | rk3128.dtsi | 437 connect = <&vop_out_lvds>;
445 connect = <&vop_out_dsi>;
|
| H A D | imx7s.dtsi | 152 /* the other input ports are not connect to anything */
203 /* the other input ports are not connect to anything */
|
| /rk3399_rockchip-uboot/examples/standalone/ |
| H A D | README.smc91111_eeprom | 64 Kermit>connect
111 Kermit>connect
|
| /rk3399_rockchip-uboot/drivers/usb/host/ |
| H A D | Kconfig | 80 will connect to EHCI if the device is high speed, otherwise they
81 connect to a companion controller. If you configure EHCI, you should
|
| /rk3399_rockchip-uboot/board/ti/ks2_evm/ |
| H A D | README | 98 and Power ON the EVM. Follow instructions to connect serial port of EVM to
110 2. Once target connect is successful, choose Tools->Load Memory option from the
|
| /rk3399_rockchip-uboot/board/sunxi/ |
| H A D | README.sunxi64 | 74 4) Initialize the USB OTG controller and will wait for a host to connect to
112 Now connect either an "A to A" USB cable to the upper USB port on the Pine64
|
| /rk3399_rockchip-uboot/board/cadence/xtfpga/ |
| H A D | README | 67 connect them. Be aware that the board has only 128 KB of SRAM,
|
| /rk3399_rockchip-uboot/board/buffalo/lsxl/ |
| H A D | README | 51 Then you enter the rescue mode, connect to the board with the ncb tool and
|
| /rk3399_rockchip-uboot/arch/arm/mach-rockchip/rk3288/ |
| H A D | Kconfig | 17 and WiFi. It has a separate power port and is designed to connect
|
| /rk3399_rockchip-uboot/drivers/usb/gadget/ |
| H A D | Kconfig | 22 you can't connect a "to-the-host" connector to a peripheral.
|
| /rk3399_rockchip-uboot/drivers/video/drm/ |
| H A D | rockchip_display.c | 1113 static int get_crtc_id(ofnode connect, bool is_ports_node) in get_crtc_id() argument
1121 port_node = of_get_parent(connect.np); in get_crtc_id()
1129 phandle = ofnode_read_u32_default(connect, "remote-endpoint", -1); in get_crtc_id()
|
| /rk3399_rockchip-uboot/drivers/spi/ |
| H A D | Kconfig | 244 Zynq QSPI IP core. This IP is used to connect the flash in
|