Home
last modified time | relevance | path

Searched refs:lilo (Results 1 – 25 of 36) sorted by relevance

12

/OK3568_Linux_fs/kernel/arch/x86/boot/
H A Dinstall.sh52 if [ -x /sbin/lilo ]; then
53 /sbin/lilo
54 elif [ -x /etc/lilo/install ]; then
55 /etc/lilo/install
H A DMakefile157 if [ -x /sbin/lilo ]; then /sbin/lilo; else /etc/lilo/install; fi
/OK3568_Linux_fs/kernel/Documentation/admin-guide/blockdev/
H A Dfloppy.rst16 lilo. This option can be typed at the boot prompt, or entered in the
17 lilo configuration file.
20 at the lilo boot prompt (if you have a thinkpad)::
24 You may also enter the following line in /etc/lilo.conf, in the description
34 If you give options both in the lilo config file and on the boot
/OK3568_Linux_fs/kernel/Documentation/fb/
H A Dsisfb.rst38 Well, it depends: If compiled statically into the kernel, use lilo's append
39 statement to add the parameters to the kernel command line. Please see lilo's
44 lilo.conf::
107 in lilo's or grub's configuration file; mode selection is done using the
H A Dintelfb.rst97 In /etc/lilo.conf, add the line::
H A Dvesafb.rst70 lilo.conf file and rerun LILO. Then you can type in the desired
H A Dintel810.rst189 In /etc/lilo.conf, add the line::
/OK3568_Linux_fs/kernel/Documentation/admin-guide/
H A Dserial-console.rst72 In lilo.conf (global section)::
77 again in lilo.conf (kernel section)::
H A DREADME.rst267 possible to do ``make install`` if you have lilo installed to suit the
268 kernel makefiles, but you may want to check your particular lilo setup first.
309 uses the kernel image as specified in the file /etc/lilo.conf. The
316 Reinstalling LILO is usually a matter of running /sbin/lilo.
317 You may wish to edit /etc/lilo.conf to specify an entry for your
H A Dldm.rst102 If you enable LDM support, then lilo is capable of booting from any of the
H A Dinitrd.rst59 have to specify the RAM disk image file in /etc/lilo.conf, using the
196 or to the section of the respective kernel in ``/etc/lilo.conf``, and pass
203 and run ``/sbin/lilo``
/OK3568_Linux_fs/yocto/meta-openembedded/meta-initramfs/recipes-devtools/grubby/
H A Dgrubby_8.40.bb3 about the configuration files for the grub, lilo, elilo (ia64), yaboot (powerpc) and \
H A Dgrubby_git.bb3 about the configuration files for the grub, lilo, elilo (ia64), yaboot (powerpc) and \
/OK3568_Linux_fs/kernel/Documentation/networking/device_drivers/appletalk/
H A Dcops.rst46 Or in lilo.conf put something like this::
H A Dltpc.rst24 as the following to your /etc/lilo.conf::
/OK3568_Linux_fs/kernel/Documentation/cdrom/
H A Dide-cd.rst184 lilo option. See Documentation/ide/ide.rst. (This feature was
188 driver to assume that one exists by using a lilo option of the
251 adding `append="hdX=noprobe hdX=cdrom"` to your lilo.conf file and running
252 lilo (again where X is the drive letter corresponding to where your drive
/OK3568_Linux_fs/kernel/Documentation/driver-api/serial/
H A Dmoxa-smartio.rst419 g. If you use 'lilo' utility, you should check /etc/lilo.conf
422 After checking /etc/lilo.conf, please run "lilo".
/OK3568_Linux_fs/kernel/Documentation/x86/i386/
H A DIO-APIC.rst45 is non-trivial though and cannot be automated. One sample /etc/lilo.conf
/OK3568_Linux_fs/kernel/Documentation/power/
H A Dswsusp-dmcrypt.rst44 modify. For lilo the simplest setup looks like the following
/OK3568_Linux_fs/yocto/meta-openembedded/meta-webserver/recipes-webadmin/webmin/
H A Dwebmin_1.850.bb41 rm -rf lilo frox wuftpd telnet pserver cpan shorewall webalizer cfengine fsdump pap
/OK3568_Linux_fs/kernel/drivers/tty/serial/
H A DKconfig45 your boot loader (lilo or loadlin) about how to pass options to the
73 your boot loader (lilo or loadlin) about how to pass options to the
429 your boot loader (lilo or loadlin) about how to pass options to the
462 your boot loader (lilo or loadlin) about how to pass options to the
491 your boot loader (lilo or loadlin) about how to pass options to the
838 your boot loader (lilo or loadlin) about how to pass options to the
/OK3568_Linux_fs/kernel/Documentation/scsi/
H A Dscsi-changer.rst101 (append="max_scsi_luns=1" in lilo.conf should do the trick)
H A Dadvansys.rst177 recognize the 'advansys' LILO command line and /etc/lilo.conf option.
H A DBusLogic.rst561 LILO Linux Boot Loader (in /etc/lilo.conf)::
594 Then install "arch/x86/boot/zImage" as your standard kernel, run lilo if
H A Dsym53c8xx_2.rst498 Example of boot setup command under lilo prompt::
500 lilo: linux root=/dev/sda2 sym53c8xx.cmd_per_lun=4 sym53c8xx.sync=10 sym53c8xx.debug=0x200

12