Searched hist:"75 c57a3570ec0904c14394db08ef436a8b49dda4" (Results 1 – 3 of 3) sorted by relevance
| /rk3399_rockchip-uboot/arch/arm/include/asm/arch-omap3/ |
| H A D | mem.h | 75c57a3570ec0904c14394db08ef436a8b49dda4 Fri Nov 18 12:48:08 UTC 2011 Tom Rini <trini@ti.com> OMAP3: Add SPL support to Beagleboard
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
logic is also based on what x-loader does in these cases. Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
0x80100000.
Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
| /rk3399_rockchip-uboot/board/ti/beagle/ |
| H A D | beagle.c | 75c57a3570ec0904c14394db08ef436a8b49dda4 Fri Nov 18 12:48:08 UTC 2011 Tom Rini <trini@ti.com> OMAP3: Add SPL support to Beagleboard
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
logic is also based on what x-loader does in these cases. Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
0x80100000.
Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
| /rk3399_rockchip-uboot/include/configs/ |
| H A D | omap3_beagle.h | 75c57a3570ec0904c14394db08ef436a8b49dda4 Fri Nov 18 12:48:08 UTC 2011 Tom Rini <trini@ti.com> OMAP3: Add SPL support to Beagleboard
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
logic is also based on what x-loader does in these cases. Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
0x80100000.
Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|