| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/thermal/ |
| H A D | thermal-cooling-devices.yaml | 21 - cooling-device: device used to dissipate heat either passively or actively
32 dissipated heat, e.g. regulating fan speeds.
35 heat dissipation). They also have a way to determine the state of cooling in
38 unsigned integers, where larger numbers mean greater heat dissipation. The
|
| H A D | thermal-sensor.yaml | 21 - cooling-device: device used to dissipate heat either passively or actively
|
| H A D | thermal-zones.yaml | 21 - cooling-device: device used to dissipate heat either passively or actively
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/power/supply/ |
| H A D | max17042_battery.txt | 20 - maxim,over-heat-temp : Temperature threshold to report battery
33 maxim,over-heat-temp = <600>;
|
| /OK3568_Linux_fs/buildroot/package/cpuburn-arm/ |
| H A D | Config.in | 12 Make ARM cores generate as much heat as possible. Supports
|
| /OK3568_Linux_fs/kernel/drivers/of/unittest-data/ |
| H A D | overlay_bad_symbol.dts | 12 heat-range = < 50 75 >;
|
| H A D | overlay.dts | 11 heat-range = < 40 75 >;
|
| H A D | overlay_base.dts | 26 heat-range = < 50 75 >;
|
| /OK3568_Linux_fs/kernel/drivers/usb/serial/ |
| H A D | whiteheat.c | 177 * Connect Tech's White Heat prerenumeration driver functions
216 * Connect Tech's White Heat serial driver functions
477 * Connect Tech's White Heat callback routines
545 * Connect Tech's White Heat firmware interface
780 * Connect Tech's White Heat utility functions
|
| /OK3568_Linux_fs/kernel/drivers/net/ethernet/sfc/ |
| H A D | mcdi_mon.c | 44 SENSOR(CONTROLLER_COOLING, "Controller heat sink", COOL, -1),
46 SENSOR(PHY0_COOLING, "PHY heat sink", COOL, 0),
48 SENSOR(PHY1_COOLING, "PHY heat sink", COOL, 1),
|
| /OK3568_Linux_fs/kernel/Documentation/hwmon/ |
| H A D | k8temp.rst | 48 This temperature is defined as temperature between heat-spreader and CPU
|
| /OK3568_Linux_fs/kernel/Documentation/input/devices/ |
| H A D | appletouch.rst | 71 The touchpad sensors are very sensitive to heat, and will generate a lot of
|
| /OK3568_Linux_fs/kernel/Documentation/scsi/ |
| H A D | qlogicfas.rst | 83 work less well because of the heat, or when cables get too long for
|
| /OK3568_Linux_fs/u-boot/include/ |
| H A D | ddr_spd.h | 253 /* 64 RDIMM Thermal Heat Spreader Solution */
376 /* 132 RDIMM Thermal Heat Spreader Solution */
400 /* 132 RDIMM Thermal Heat Spreader Solution */
|
| /OK3568_Linux_fs/kernel/drivers/macintosh/ |
| H A D | windfarm_mpu.h | 60 fs32 theta_heat_sink; /* 0x48 - Theta heat sink */
|
| /OK3568_Linux_fs/kernel/drivers/thermal/ti-soc-thermal/ |
| H A D | omap3-thermal-data.c | 15 * generating heat has to be a factor as well. If you are just looking
|
| /OK3568_Linux_fs/kernel/Documentation/driver-api/thermal/ |
| H A D | cpu-idle-cooling.rst | 62 another way to control CPU power and heat in addition to
|
| /OK3568_Linux_fs/u-boot/arch/arm/dts/ |
| H A D | rk3288-veyron-mickey.dts | 117 * heat--we'll let the GPU do the rest itself.
|
| H A D | .rk3288-veyron-mickey.dtb.pre.tmp | |
| /OK3568_Linux_fs/kernel/arch/arm/boot/dts/ |
| H A D | rk3288-veyron-mickey.dts | 189 * throttle the CPU lower than 1.4 GHz due to GPU heat--we'll
|
| /OK3568_Linux_fs/kernel/drivers/iio/chemical/ |
| H A D | bme680_core.c | 305 dev_err(dev, "failed to read resistance heat range\n"); in bme680_read_calib()
312 dev_err(dev, "failed to read resistance heat value\n"); in bme680_read_calib()
|
| /OK3568_Linux_fs/kernel/include/linux/ |
| H A D | lru_cache.h | 30 the active set before we can "heat" a previously unused region.
|
| H A D | thermal.h | 266 * Sustainable power (heat) that this thermal zone can dissipate in
|
| /OK3568_Linux_fs/kernel/Documentation/powerpc/ |
| H A D | eeh-pci-error-recovery.rst | 37 as PCI cards dying from heat, humidity, dust, vibration and bad
|
| /OK3568_Linux_fs/kernel/arch/alpha/ |
| H A D | Kconfig | 577 consumed, and the heat produced by the computer. However, it has
|