| /OK3568_Linux_fs/yocto/poky/meta/files/common-licenses/ |
| H A D | FreeBSD-DOC | 17 …The Institute of Electrical and Electronics Engineers and The Open Group, have given us permission…
21 … Base Specifications Issue 6, Copyright© 2001-2004 by the Institute of Electrical and Electronics …
|
| /OK3568_Linux_fs/kernel/drivers/usb/chipidea/ |
| H A D | otg_fsm.h | 21 * Table 4-1: Electrical Characteristics
22 * ->DC Electrical Timing
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/display/panel/ |
| H A D | tpo,tpg110.yaml | 27 If some electrical strap or alternate resolution is desired,
31 certain electrical driving levels.
|
| /OK3568_Linux_fs/kernel/Documentation/driver-api/soundwire/ |
| H A D | error_handling.rst | 23 slots) or electrical issues during the transmit/receive transition cannot
35 Slave or to a non-implemented register) or electrical issue, no response
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/phy/ |
| H A D | mixel,mipi-dsi-phy.txt | 5 electrical signals for DSI.
|
| /OK3568_Linux_fs/kernel/include/linux/mtd/ |
| H A D | jedec.h | 55 /* electrical parameter block */
|
| H A D | onfi.h | 94 /* electrical parameter block */
|
| /OK3568_Linux_fs/kernel/Documentation/driver-api/ |
| H A D | miscellaneous.rst | 29 control power supplied to electrical devices.
|
| H A D | pinctl.rst | 397 is a way for chip vendors producing some kind of electrical packages to use
747 that your datasheet calls "GPIO mode", but actually is just an electrical
802 software-control a few electrical properties of the pin that you would
821 Here some electrical properties of the pin can be configured no matter
869 - Registers (or fields within registers) that control electrical
890 Electrical properties of the pin such as biasing and drive strength
969 GPIO subsystem. It is just an electrical configuration used by that device
|
| H A D | i2c.rst | 30 systems are also I2C conformant. The electrical constraints are tighter
|
| /OK3568_Linux_fs/kernel/drivers/net/ethernet/intel/e1000e/ |
| H A D | 80003es2lan.h | 64 /* 1=Enable SERDES Electrical Idle */
|
| /OK3568_Linux_fs/kernel/Documentation/driver-api/gpio/ |
| H A D | driver.rst | 62 - method to set electrical configuration for a given GPIO line
91 GPIO electrical configuration
94 GPIO lines can be configured for several electrical modes of operation by using
250 supports more versatile control over electrical properties and can handle
|
| H A D | board.rst | 136 electrical state during suspend/resume
|
| /OK3568_Linux_fs/kernel/Documentation/i2c/ |
| H A D | summary.rst | 27 meet both SMBus and I2C electrical constraints; and others which can't
|
| /OK3568_Linux_fs/u-boot/arch/powerpc/cpu/mpc85xx/ |
| H A D | p1021_serdes.c | 79 /* Init SERDES Receiver electrical idle detection control for PCIe */ in fsl_serdes_init()
|
| /OK3568_Linux_fs/kernel/Documentation/networking/ |
| H A D | phy.rst | 69 (RG)MII/electrical interface considerations
73 electrical signal interface using a synchronous 125Mhz clock signal and several
277 also defines the electrical characteristics of the signals with a host
|
| /OK3568_Linux_fs/kernel/Documentation/i2c/busses/ |
| H A D | i2c-ali15x3.rst | 119 There may be electrical problems on this board.
|
| /OK3568_Linux_fs/kernel/drivers/gpio/ |
| H A D | gpio-mlxbf.c | 18 /* Pad Electrical Controls. */
|
| /OK3568_Linux_fs/kernel/Documentation/driver-api/serial/ |
| H A D | serial-rs485.rst | 9 electrical characteristics of drivers and receivers for use in balanced
|
| /OK3568_Linux_fs/kernel/Documentation/powerpc/ |
| H A D | eeh-pci-error-recovery.rst | 38 electrical connections. The vast majority of EEH errors seen in
50 address line parity errors (for example, due to poor electrical
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/net/ |
| H A D | mscc-phy-vsc8531.txt | 15 is to help reduce electrical emission (EMI)
|
| /OK3568_Linux_fs/kernel/drivers/misc/echo/ |
| H A D | echo.h | 25 electrical echoes (e.g. from 2-4 wire hybrids) from voice calls.
|
| /OK3568_Linux_fs/kernel/drivers/soc/bcm/ |
| H A D | bcm2835-power.c | 198 /* Enable electrical isolation */ in bcm2835_power_power_off()
245 /* Disable electrical isolation */ in bcm2835_power_power_on()
|
| /OK3568_Linux_fs/kernel/arch/mips/alchemy/ |
| H A D | board-gpr.c | 210 * The open drain mode is hardwired somewhere or an electrical
|
| /OK3568_Linux_fs/kernel/drivers/usb/misc/ |
| H A D | Kconfig | 197 used for the USB-IF Embedded Host High-Speed Electrical Test procedure.
|