| /OK3568_Linux_fs/u-boot/arch/arm/mach-imx/mx7/ |
| H A D | Kconfig | 12 config MX7D config
24 select MX7D
31 select MX7D
38 select MX7D
|
| H A D | psci-mx7.c | 21 /* below is for i.MX7D */
|
| H A D | soc.c | 222 * i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports in imx_enet_mdio_fixup()
|
| /OK3568_Linux_fs/buildroot/board/freescale/imx7dsdb/ |
| H A D | readme.txt | 2 Freescale i.MX7D SDB board
5 This file documents the Buildroot support for the Freescale i.MX7D SDB board.
10 First, configure Buildroot for your i.MX7D SDB board:
45 Boot the i.MX7D SDB board
|
| /OK3568_Linux_fs/buildroot/board/technexion/imx7dpico/ |
| H A D | readme.txt | 2 Technexion i.MX7D Pico board
5 This file documents the Buildroot support for the Technexion i.MX7D Pico board.
10 First, configure Buildroot for the i.MX7D Pico board:
105 Boot the i.MX7D Pico board
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/arm/ |
| H A D | fsl.yaml | 360 - description: i.MX7D based Boards
366 - technexion,imx7d-pico-dwarf # TechNexion i.MX7D Pico-Dwarf
367 - technexion,imx7d-pico-hobbit # TechNexion i.MX7D Pico-Hobbit
368 - technexion,imx7d-pico-nymph # TechNexion i.MX7D Pico-Nymph
369 - technexion,imx7d-pico-pi # TechNexion i.MX7D Pico-Pi
379 - tq,imx7d-mba7 # i.MX7D TQ MBa7 with TQMa7D SoM
|
| /OK3568_Linux_fs/u-boot/configs/ |
| H A D | colibri_imx7_defconfig | 9 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/toradex/colibri_imx7/imximage.cfg,MX7D"
|
| /OK3568_Linux_fs/u-boot/drivers/pinctrl/nxp/ |
| H A D | Kconfig | 41 i.MX7D. This feature depends on device tree
|
| /OK3568_Linux_fs/u-boot/arch/arm/mach-imx/ |
| H A D | imx_bootaux.c | 31 * To i.MX6SX and i.MX7D, the image supported by bootaux needs
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/nvmem/ |
| H A D | imx-ocotp.yaml | 15 i.MX7D/S, i.MX7ULP, i.MX8MQ, i.MX8MM, i.MX8MN and i.MX8MP SoCs.
|
| /OK3568_Linux_fs/u-boot/include/configs/ |
| H A D | pico-imx7d.h | 4 * Configuration settings for the i.MX7D Pico board.
|
| H A D | mx7dsabresd.h | 4 * Configuration settings for the Freescale i.MX7D SABRESD board.
|
| /OK3568_Linux_fs/u-boot/arch/arm/include/asm/mach-imx/ |
| H A D | rdc-sema.h | 33 /* The Following macro definitions are common to i.MX6SX and i.MX7D */
|
| /OK3568_Linux_fs/kernel/drivers/usb/dwc3/ |
| H A D | dwc3-haps.c | 110 * i.MX6QP and i.MX7D platform use a PCIe controller with the
|
| /OK3568_Linux_fs/kernel/arch/arm/mach-imx/ |
| H A D | anatop.c | 114 * On i.MX7D digprog value match linux version format, so in imx_init_revision_from_anatop()
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/pci/ |
| H A D | fsl,imx6q-pcie.txt | 89 * Freescale i.MX7d PCIe PHY
|
| /OK3568_Linux_fs/kernel/drivers/soc/imx/ |
| H A D | soc-imx.c | 114 soc_id = "i.MX7D"; in imx_soc_device_init()
|
| /OK3568_Linux_fs/u-boot/arch/arm/include/asm/arch-mx7/ |
| H A D | clock.h | 43 /* PLL supported by i.mx7d */
|
| /OK3568_Linux_fs/u-boot/board/technexion/pico-imx7d/ |
| H A D | pico-imx7d.c | 281 puts("Board: i.MX7D PICOSOM\n"); in checkboard()
|
| /OK3568_Linux_fs/u-boot/board/freescale/mx7dsabresd/ |
| H A D | mx7dsabresd.c | 393 printf("Board: i.MX7D SABRESD in %s mode\n", mode); in checkboard()
|
| /OK3568_Linux_fs/kernel/drivers/usb/chipidea/ |
| H A D | usbmisc_imx.c | 475 * For SoCs like i.MX7D and later, each USB controller has in usbmisc_imx6_hsic_get_reg_offset()
476 * its own non-core register region. For SoCs before i.MX7D, in usbmisc_imx6_hsic_get_reg_offset()
|
| /OK3568_Linux_fs/u-boot/env/ |
| H A D | Kconfig | 8 default ENV_IS_IN_MMC if MX6SX || MX7D
|
| /OK3568_Linux_fs/kernel/drivers/iio/adc/ |
| H A D | imx7d_adc.c | 3 * Freescale i.MX7D ADC driver
|
| /OK3568_Linux_fs/kernel/arch/arm/ |
| H A D | Kconfig.debug | 482 bool "i.MX7D Debug UART"
486 on i.MX7D.
|
| /OK3568_Linux_fs/kernel/drivers/thermal/ |
| H A D | imx_thermal.c | 444 * On i.MX7D, we only use the calibration data at 25C to get the temp, in imx_init_calib()
|