Lines Matching +full:0 +full:x42000000
18 #define PHYS_SDRAM_1 0x40000000 /* Base address */
19 #define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */
60 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
75 #define CONFIG_DEFAULT_SPI_CS 0
81 #define CONFIG_SF_DEFAULT_CS 0
86 #define CONFIG_ENV_SPI_CS 0
106 #define CONFIG_LOADADDR 0x42000000
114 "consdev=ttyAMA0\0" \
115 "baudrate=115200\0" \
116 "bootscript=boot.scr\0" \
117 "bootdev=/dev/mmcblk0p2\0" \
118 "rootdev=/dev/mmcblk0p3\0" \
119 "netdev=eth0\0" \
120 "hostname=m28evk\0" \
121 "rootpath=/opt/eldk-5.5/armv5te/rootfs-qte-sdk\0" \
122 "kernel_addr_r=0x42000000\0" \
123 "videomode=video=ctfb:x:800,y:480,depth:18,mode:0,pclk:30066," \
124 "le:0,ri:256,up:0,lo:45,hs:1,vs:1,sync:100663296," \
125 "vmode:0\0" \
126 "update_nand_full_filename=u-boot.nand\0" \
127 "update_nand_firmware_filename=u-boot.sb\0" \
128 "update_sd_firmware_filename=u-boot.sd\0" \
129 "update_nand_firmware_maxsz=0x100000\0" \
130 "update_nand_stride=0x40\0" /* MX28 datasheet ch. 12.12 */ \
131 "update_nand_count=0x4\0" /* MX28 datasheet ch. 12.12 */ \
133 "nand device 0 ; " \
136 "setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
140 "nand scrub -y 0x0 ${filesize} ; " \
141 "nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; " \
145 "fi\0" \
155 "fi\0" \
159 "setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
161 "mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
163 "fi\0" \
166 "console=${consdev},${baudrate}\0" \
170 "${netmask}:${hostname}:${netdev}:off\0" \
172 "setenv bootargs ${bootargs} ${miscargs}\0" \
176 "fi\0" \
179 "setenv bootargs ${bootargs} ${mtdparts}\0" \
180 "addargs=run addcons addmtd addmisc\0" \
183 "load mmc 0:2 ${kernel_addr_r} ${bootfile}\0" \
186 "ubifsload ${kernel_addr_r} /boot/${bootfile}\0" \
188 "tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \
189 "miscargs=nohlt panic=1\0" \
190 "mmcargs=setenv bootargs root=${rootdev} rw rootwait\0" \
193 "root=ubi0:rootfs rootfstype=ubifs\0" \
196 "nfsroot=${serverip}:${rootpath},v3,tcp\0" \
199 "bootm ${kernel_addr_r}\0" \
202 "bootm ${kernel_addr_r}\0" \
205 "bootm ${kernel_addr_r}\0" \
208 "bootm ${kernel_addr_r}\0" \
211 "bootm ${kernel_addr_r}\0" \
214 "bootm ${kernel_addr_r}\0" \
217 "bootm ${kernel_addr_r}\0" \
220 "bootm ${kernel_addr_r}\0" \
223 "bootm ${kernel_addr_r}\0" \
226 "if test -e mmc 0:2 ${bootscript} ; then " \
227 "if load mmc 0:2 ${kernel_addr_r} ${bootscript};" \
232 "fi\0"