Lines Matching +full:usb +full:- +full:controller

2 # USB Host Controller Drivers
4 comment "USB Host Controller Drivers"
10 	bool "xHCI HCD (USB 3.0) support"
12 	---help---
13 	  The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
14 	  "SuperSpeed" host controller hardware.
22 	  USB controller based on the DesignWare USB3 IP Core.
30 	  USB controller based on the DesignWare USB3 IP Core.
33 	bool "MVEBU USB 3.0 support"
38 	  Choose this option to add support for USB 3.0 driver on mvebu
43 	bool "Support for PCI-based xHCI USB controller"
47 	  Enables support for the PCI-based xHCI controller.
50 	bool "Renesas RCar USB 3.0 support"
54 	  Choose this option to add support for USB 3.0 driver on Renesas
58 	int "DRA7XX xHCI USB index"
63 	  Select the DRA7XX xHCI USB index.
69 	bool "EHCI HCD (USB 2.0) support"
72 	---help---
73 	  The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
74 	  "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
75 	  If your USB host controller supports USB 2.0, you will likely want to
76 	  configure this Host Controller Driver.
79 	  or UHCI) to handle USB 1.1 devices connected to root hub ports.  Ports
81 	  connect to a companion controller.  If you configure EHCI, you should
82 	  probably configure the OHCI (for NEC and some other vendors) USB Host
83 	  Controller Driver or UHCI (for Via motherboards) Host Controller
86 	  You may want to read <file:Documentation/usb/ehci.txt>.
91 	bool  "Support for Atmel on-chip EHCI USB controller"
94 	---help---
95 	  Enables support for the on-chip EHCI controller on Atmel chips.
98 	bool "Support for Marvell on-chip EHCI USB controller"
101 	---help---
102 	  Enables support for the on-chip EHCI controller on MVEBU SoCs.
105 	bool "Support for i.MX6/i.MX7ULP on-chip EHCI USB controller"
108 	---help---
109 	  Enables support for the on-chip EHCI controller on i.MX6 SoCs.
112 	bool "Support for i.MX7 on-chip EHCI USB controller"
115 	---help---
116 	  Enables support for the on-chip EHCI controller on i.MX7 SoCs.
119 	bool "Support for OMAP3+ on-chip EHCI USB controller"
122 	---help---
123 	  Enables support for the on-chip EHCI controller on OMAP3 and later
127 	bool "Support for Vybrid on-chip EHCI USB controller"
131 	  Enables support for the on-chip EHCI controller on Vybrid SoCs.
136 	bool "USB Power pin high active"
137 	---help---
138 	  Set the USB Power pin polarity to be high active (PWR_POL)
143 	bool "Support for Qualcomm on-chip EHCI USB controller"
147 	---help---
148 	  Enables support for the on-chip EHCI controller on Qualcomm
150 	  This driver supports combination of Chipidea USB controller
151 	  and Synapsys USB PHY in host mode only.
154 	bool "Support for PCI-based EHCI USB controller"
157 	  Enables support for the PCI-based EHCI controller.
160 	bool "Support for Xilinx Zynq on-chip EHCI USB controller"
163 	---help---
164 	  Enable support for Zynq on-chip EHCI USB controller
167 	bool "Support for generic EHCI USB controller"
171 	---help---
172 	  Enables support for generic EHCI controller.
177 	bool "OHCI HCD (USB 1.1) support"
178 	---help---
179 	  The Open Host Controller Interface (OHCI) is a standard for accessing
180 	  USB 1.1 host controller hardware.  It does more in hardware than Intel's
181 	  UHCI specification.  If your USB host controller follows the OHCI spec,
182 	  say Y.  On most non-x86 systems, and on x86 hardware that's not using a
183 	  USB controller from Intel or VIA, this is appropriate.  If your host
184 	  controller doesn't use PCI, this is probably appropriate.  For a PCI
185 	  based system where you're not sure, the "lspci -v" entry will list the
186 	  right "prog-if" for your USB controller(s):  EHCI, OHCI, or UHCI.
189 	bool "Support for PCI-based OHCI USB controller"
193 	  Enables support for the PCI-based OHCI controller.
198 	bool "Support for generic OHCI USB controller"
202 	---help---
203 	  Enables support for generic OHCI controller.
206 	bool "Support for da850 OHCI USB controller"
208 	  Enable support for the da850 USB controller.
215 	---help---
216 	  The Universal Host Controller Interface is a standard by Intel for
217 	  accessing the USB hardware in the PC (which is also called the USB
218 	  host controller). If your USB host controller conforms to this
223 	  133) and LEON/GRLIB SoCs with the GRUSBHC controller.
233 	---help---
234 	  The DesignWare USB 2.0 controller is compliant with the
235 	  USB-Implementers Forum (USB-IF) USB 2.0 specifications.
236 	  Hi-Speed (480 Mbps), Full-Speed (12 Mbps), and Low-Speed (1.5 Mbps)
237 	  operation is compliant to the controller Supplement. If you want to
238 	  enable this controller in host mode, say Y.
244 	---help---
253 	bool "Renesas R8A66597 USB Core support"
257 	---help---
258 	  This enables support for the on-chip Renesas R8A66597 USB 2.0
259 	  controller, present in various RZ and SH SoCs.