Kconfig - OpenGrok cross reference for /OK3568_Linux_fs/u-boot/drivers/power/Kconfig

1 menu "Power"  menu
3 source "drivers/power/domain/Kconfig"
5 source "drivers/power/fuel_gauge/Kconfig"
7 source "drivers/power/io-domain/Kconfig"
9 source "drivers/power/pmic/Kconfig"
11 source "drivers/power/power_delivery/Kconfig"
13 source "drivers/power/regulator/Kconfig"
15 source "drivers/power/dvfs/Kconfig"
17 source "drivers/power/charge/Kconfig"
35 	---help---
42 	---help---
50 	---help---
58 	---help---
66 	---help---
73 	---help---
80 	---help---
94 	bool "Enable Rockchip power manager for charge animation"
98 	  This adds power manage control of devices for low power
106 	---help---
109 	generic 3.3V IO voltage for external devices like the lcd-panal and
111 	save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
112 	dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
123 	---help---
126 	On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
127 	On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
128 	On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
130 	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
131 	On R40 boards dcdc2 is VDD-CPU and should be 1.1V
141 	---help---
144 	On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
146 	On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
147 	On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
148 	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
149 	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
150 	On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
159 	---help---
162 	On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
163 	On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
165 	On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
166 	On A83T boards dcdc4 is used for VDD-GPU.
172 	---help---
175 	On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and
184 	---help---
187 	On A31 boards aldo1 is often used to power the wifi module.
188 	On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
200 	---help---
206 	On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
208 	On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
216 	---help---
220 	On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should
223 	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
230 	---help---
239 	---help---
242 	to power the ethernet phy. On A23, A33 and A80 boards this is often
243 	used to power the wifi.
250 	---help---
259 	---help---
267 	---help---
275 	---help---
283 	---help---
292 	---help---
303 	---help---
306 	On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
313 	---help---
316 	On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
322 	---help---
330 	---help---
337 	---help---
339 	is typically used to power the VDD-CPU and should be 1200mV.
344 	bool "Enable driver for TI TWL4030 power management chip"
346 	---help---
347 	The TWL4030 in a combination audio CODEC/power management with