Lines Matching full:boards

36 	Select this for boards which do not use a PMIC.
44 	A10s boards.
52 	A10, A13 and A20 boards.
60 	A23 and A31 boards.
67 	Say y here to enable support for the axp809 pmic found on A80 boards.
82 	H3 boards.
108 	disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
110 	sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
126 	On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
127 	On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
128 	On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
129 	On A80 boards dcdc2 powers the GPU and can be left off.
130 	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
131 	On R40 boards dcdc2 is VDD-CPU and should be 1.1V
144 	On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
146 	On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
147 	On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
148 	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
149 	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
150 	On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
162 	On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
163 	On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
164 	On A23 / A33 boards dcdc4 is unused and should be disabled.
165 	On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
166 	On A83T boards dcdc4 is used for VDD-GPU.
175 	On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and
187 	On A31 boards aldo1 is often used to power the wifi module.
188 	On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
189 	On A80 boards aldo1 powers the USB hosts and should be 3.0V.
190 	On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
203 	On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
204 	On A31 boards aldo2 is typically unused and should be disabled.
205 	On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
206 	On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
207 	On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
208 	On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
219 	On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
220 	On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should
222 	On A80 boards aldo3 is normally not used.
223 	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
233 	On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
241 	disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
242 	to power the ethernet phy. On A23, A33 and A80 boards this is often
253 	On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
297 	On A80 boards it powers the PM pingroup and should be 3.0V.
306 	On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
316 	On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.