Lines Matching +full:mtd +full:- +full:ram
35 default "arch/$(ARCH)/cpu/u-boot-spl.lds"
38 The SPL stage will usually require a different linker-script
40 U-Boot stage. Set this to the path of the linker-script to
44 bool "Call board-specific initialization in SPL"
46 If this option is enabled, U-Boot will call the function
54 ROM for loading the next boot-stage after performing basic setup
58 BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
85 usage as the *_simple malloc functions do not re-use free-ed mem.
94 usage as the *_simple malloc functions do not re-use free-ed mem.
103 location for the SPL stack. U-Boot SPL switches to this after
127 because RAM is already set up. In this case BSS can be moved to RAM.
133 bool "Display a board-specific message in SPL"
135 If this option is enabled, U-Boot will call the function
137 banner ("U-Boot SPL ..."). This function should be provided by
162 The address on the ram where the SPL relocate to.
171 Use sector number for specifying U-Boot location on MMC/SD in
175 hex "Address on the MMC to load U-Boot from"
187 Address on the MMC to load U-Boot from, when the MMC is being used
194 Use a partition for loading U-Boot when using MMC/SD in raw mode.
197 hex "Partition to use to load U-Boot from"
201 Partition on the MMC to load U-Boot from when the MMC is being
208 Use partition type for specifying U-Boot partition on MMC/SD in
209 raw mode. U-Boot will be loaded from the first partition of this
213 string "Partition Name on the MMC to load U-Boot from"
217 Partition Name on the MMC to load U-Boot from, when the MMC is being
221 hex "Partition Type on the MMC to load U-Boot from"
224 Partition Type on the MMC to load U-Boot from, when the MMC is being
237 32-bit checksum value that can be used to verify images. This is
247 checksum is a 128-bit hash value used to check that the image
249 secure as it is possible (with a brute-force attack) to adjust the
260 checksum is a 160-bit (20-byte) hash value used to check that the
263 due to the expanding computing power avaiable to brute-force
272 checksum is a 256-bit (32-byte) hash value used to check that the
278 supported in U-Boot.
290 first image to be treated as having a U-Boot style calling
320 this option to build system-specific drivers for hash acceleration
326 Enable DMA (direct-memory-access) drivers in SPL. These drivers
327 can be used to handle memory-to-peripheral data transfer without
342 Enable environment support in SPL. The U-Boot environment provides
344 control many aspects of U-Boot's operation. Normally this is not
348 starting U-Boot first. Enabling this option will make env_get()
370 drivers in SPL. This permits SPL to load U-Boot over an Ethernet
371 link rather than from an on-board peripheral. Environment support
379 U-Boot (or Linux in Falcon mode) to be loaded from an EXT
388 permits U-Boot (or Linux in Falcon mode) to be loaded from a FAT
395 Enable support for FPGAs in SPL. Field-programmable Gate Arrays
396 provide software-configurable hardware which is typically used to
406 Enable support for GPIOs (General-purpose Input/Output) in SPL.
407 GPIOs allow U-Boot to read the state of an input line (high or
410 input. GPIOs can be useful in SPL to enable a 'sign-of-life' LED,
417 Enable support for the I2C (Inter-Integrated Circuit) bus in SPL.
430 Enable support for common U-Boot libraries within SPL. These
431 libraries include common code to deal with U-Boot images,
440 of a misnomer as it includes non-spinning media such as flash (as
447 U-Boot to also be used in SPL. It brings in the code in disk/.
452 Enable support for generic U-Boot libraries within SPL. These
480 Enable support for DDR-SDRAM (double-data-rate synchronous dynamic
481 random-access memory) on the MPC8XXX family within SPL. This
482 allows DRAM to be set up before loading U-Boot into that DRAM,
486 bool "Support MTD drivers"
488 Enable support for MTD (Memory Technology Device) within SPL. MTD
490 SPI flash. This allows SPL to load U-Boot from supported MTD
492 to enable specific MTD drivers.
495 hex "Location in MTD block to read U-Boot from"
500 u-boot should be loaded from.
514 the drivers in drivers/usb/musb-new as part of an SPL build. The
521 can be used to allow SPL to load U-Boot from supported devices.
522 This enables the drivers in drivers/mtd/nand/raw as part of an SPL
529 This permits SPL to load U-Boot over a network link rather than
530 from an on-board peripheral. Environment support is required since
542 SPL or U-Boot itself makes the request
548 This is specific to the ARM926EJ-S CPU. It disables the standard
549 start.S start-up code, presumably so that a replacement can be
556 Enable support for loading U-Boot from memory-mapped NOR (Negative
558 a memory-mapped device makes it very easy to access. Loading from
565 Enable support for execute in place of U-Boot or kernel image. There
566 is no need to copy image from flash to ram if flash supports execute
568 enough ram to load the image.
575 load U-Boot from supported devices. This enables the drivers in
576 drivers/mtd/onenand as part of an SPL build.
616 image as a RAM partition for firmware.
621 Enable support for POST (Power-on Self Test) in SPL. POST is a
631 for PMICs (Power-management Integrated Circuits) and some of the
647 bool "Support booting from RAM"
650 Enable booting of an image in RAM. The image can be preloaded or
651 it can be loaded by SPL directly into RAM (e.g. using USB).
654 bool "Support booting from preloaded image in RAM"
658 Enable booting of an image already loaded in RAM. The image has to
665 Enable RTC (Real-time Clock) support in SPL. This includes support
667 non-volatile (battery-backed) memory which is accessible if
676 loading U-Boot. SATA is used in higher-end embedded systems and
693 Enable support for using SPI flash in SPL, and loading U-Boot from
696 but fast bidirectional 4-wire bus (clock, chip select and two data
697 lines). This enables the drivers in drivers/mtd/spi as part of an
710 hex "Location in RKNAND block to read U-Boot from"
715 u-boot should be loaded from.
739 Enable support for loading next stage, U-Boot or otherwise, from
740 SPI NOR in U-Boot SPL.
748 to SPI flash for loading U-Boot. See SPL_SPI_FLASH_SUPPORT for
758 SPL can load U-Boot from a connected USB peripheral, such as a USB
769 devices such as hard drives and flash drivers for loading U-Boot.
770 The actual drivers are enabled separately using the normal U-Boot
786 drivers in SPL. This permits SPL to load U-Boot over a
787 USB-connected Ethernet link (such as a USB Ethernet dongle) rather
799 RAM memory device support. The ROM code will load and execute
800 the SPL built with dfu. The user can load binaries (u-boot/kernel) to
801 selected device partition from host-pc using dfu-utils.
802 This feature is useful to flash the binaries to factory or bare-metal
810 bool "RAM device"
813 select RAM/DDR memory device for loading binary images
814 (u-boot/kernel) to the selected device partition using
815 DFU and execute the u-boot/kernel from RAM.
840 means of transmitting U-Boot over a serial line for using in SPL,
849 More detail at: https://github.com/ARM-software/arm-trusted-firmware
852 bool "Support OP-TEE Trusted OS"
855 OP-TEE is an open source Trusted OS which is loaded by SPL.
856 More detail at: https://github.com/OP-TEE/optee_os
864 not U-Boot aware and have an insufficiently robust parameter
867 If this option is enabled, the spl_atf os-type handler will
879 bool "Support OP-TEE Trusted OS"
882 OP-TEE is an open source Trusted OS which is loaded by SPL.
883 More detail at: https://github.com/OP-TEE/optee_os
897 for trust and U-Boot images.
999 bool "Call board-specific initialization in TPL"
1001 If this option is enabled, U-Boot will call the function
1009 The TPL stage will usually require a different linker-script
1011 U-Boot stage. Set this to the path of the linker-script to
1015 fall back to the linker-script used for the SPL stage.
1018 bool "TPL needs a separate text-base"
1022 Enable, if the TPL stage should not inherit its text-base
1027 bool "TPL needs a separate initial stack-pointer"
1032 stack-pointer from the settings for the SPL stage.
1048 hex "Address of the initial stack-pointer for the TPL stage"
1051 The address of the initial stack-pointer for the TPL stage.
1052 Usually this will be the (aligned) top-of-stack.
1058 ROM for loading the next boot-stage after performing basic setup
1062 BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
1087 Enable support for common U-Boot libraries within TPL. See
1093 Enable support for generic U-Boot libraries within TPL. See
1104 Enable support for DDR-SDRAM on the MPC8XXX family within TPL. See