Kconfig - OpenGrok cross reference for /OK3568_Linux_fs/u-boot/common/Kconfig

25 	  Enable recording of boot time in SPL. To make this visible to U-Boot
27 	  information when SPL finishes and load it when U-Boot proper starts
35 	  This shows how long it took U-Boot to go through each stage of the
126 	  Enabling this will make a U-Boot binary that is capable of being
135 	  Enabling this will make a U-Boot binary that is capable of being
143 	  Enabling this will make a U-Boot binary that is capable of being
151 	  Enabling this will make a U-Boot binary that is capable of being
159 	  Enabling this will make a U-Boot binary that is capable of being
167 	  Enabling this will make a U-Boot binary that is capable of being
175 	  Enabling this will make a U-Boot binary that is capable of being
186 	  "serial-number" properties.
195 	  set to -1 to disable autoboot.
196 	  set to -2 to autoboot with no delay and not check for abort
206 	  will be undefined and won't take any space in U-Boot image.
226 	  This is the library functionality to provide a text-based menu of
262 	  This disable CLI interactive in verified-boot.
272 	  This options adds the board specific name to u-boot version.
289 	  7 (KERN_DEBUG)          debug-level messages
300 	  setting the environment vaariable 'silent' to a non-empty value.
308 	bool "Only silence the U-Boot console"
311 	  Normally when the U-Boot console is silenced, Linux's console is
313 	  allows the linux console to operate normally, even if U-Boot's
323 	  to silence or un-silence the console.
341 	  Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
347 	  useful to be able to share the pre-console buffer with SPL.
350 	int "Sets the size of the pre-console buffer"
354 	  The size of the pre-console buffer affects how much console output
362 	  option only the post-relocation output will be displayed.
365 	hex "Address of the pre-console buffer"
370 	  This sets the start address of the pre-console buffer. This must
386 	  adds a small amount of size to U-Boot.  Changes to the environment
402 	  If this is enabled, and the board-specific function
412 	  used to determine the correct console devices on start-up. This
414 	  start-up (after relocation). This causes the environment to be
420 	  Normally U-Boot displays the current settings for stdout, stdin
421 	  and stderr on boot when the post-relocation console is set up.
463 	    0 - panic
464 	    1 - critical
465 	    2 - error
466 	    3 - warning
467 	    4 - note
468 	    5 - info
469 	    6 - detail
470 	    7 - debug
481 	    0 - panic
482 	    1 - critical
483 	    2 - error
484 	    3 - warning
485 	    4 - note
486 	    5 - info
487 	    6 - detail
488 	    7 - debug
497 	  log message is shown - other details like level, category, file and
507 	  log message is shown - other details like level, category, file and
528 	bool "add U-Boot environment variable vers"
532 	  named "ver" is created by U-Boot showing the U-Boot
542 	  boot-modes etc. which eventually done at late.
551 	  Display information about the CPU that U-Boot is running on
552 	  when U-Boot starts up. The function print_cpuinfo() is called
559 	  Display information about the board that U-Boot is running on
560 	  when U-Boot starts up. The board function checkboard() is called
563 menu "Start-up hooks"
566 	bool "Call arch-specific init soon after relocation"
568 	  With this option U-Boot will call arch_early_init_r() soon after
571 	  enabled. This can be used to set up architecture-specific devices.
574 	bool "Call arch-specific init after relocation, when console is ready"
576 	  With this option U-Boot will call arch_misc_init() after
577 	  relocation to allow miscellaneous arch-dependent initialisation
582 	bool "Call board-specific init before relocation"
585 	  after boot. With this option, U-Boot calls board_early_init_f()
586 	  after driver model is ready in the pre-relocation init sequence.
591 	bool "Call board-specific init after relocation"
594 	  relocation. With this option, U-Boot calls board_early_init_r()
595 	  in the post-relocation init sequence.
609 	  The BCB is used to determine the boot mode of the device (normal mode,
610 	  recovery mode or bootloader mode) and, if enabled, the slot to boot
668 	bool "Skip U-Boot relocation"
671 	  This enable support for skipping U-Boot relocation.
681 	  also CMD_HASH for command-line access.