Lines Matching +full:no +full:- +full:regulator +full:- +full:enable +full:- +full:control
4 bool "Support U-Boot commands"
7 Enable U-Boot's command-line functions. This provides a means
8 to enter commands into U-Boot for a wide variety of purposes. It
12 substantially to the size of U-Boot.
34 bool "Enable cmd with U_BOOT_CMD_ALWAYS() declared"
37 This function is used to support some special U-Boot commands with
56 U-Boot automatic booting process and bring the device
57 to the U-Boot prompt for user input.
65 CONFIG_BOOTDELAY starts. If it is not defined there is no
76 bool "Enable encryption in autoboot stopping"
88 autoboot starts booting, U-Boot gives a command prompt. The
89 U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is
101 U-Boot gives a command prompt. The U-Boot prompt never
105 bool "Enable Ctrl-C autoboot interruption"
110 by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey".
119 and therefore boot into the U-Boot prompt, when the input
148 in the U-Boot image and can be printed on the console by the "config"
150 the running U-Boot.
219 This compiles a standard EFI hello world application with U-Boot so
224 No additional space will be required in the resulting U-Boot binary
231 This adds a standard EFI hello world application to U-Boot so that
292 Extract a part of a multi-image.
300 bool "spl export - Export boot information for Falcon boot"
304 System such as Linux, thus skipping U-Boot proper. See
309 hex "Offset of OS command line args for Falcon-mode NAND boot"
323 This provides the size of the command-line argument area in NAND
324 flash used by Falcon-mode boot. See the documentation until CMD_SPL
328 bool "thor - TIZEN 'thor' download"
332 There is no documentation about this within the U-Boot source code
336 bool "zboot - x86 boot command"
344 booting both 32- and 64-bit kernels, as well as secure boot.
345 Documentation is available in doc/uImage.FIT/x86-fit-boot.txt
383 Save all environment variables into the compiled-in persistent
394 bool "env callbacks - print callbacks and their associated variables"
402 bool "env flags -print variables that have non-default flags"
404 Some environment variables have special flags that control their
421 bool "crc32 -v"
424 Add -v option to verify data against a crc32 checksum.
427 bool "eeprom - EEPROM subsystem"
435 bool "Enable layout-aware eeprom commands"
439 When enabled, additional eeprom sub-commands become available.
441 eeprom print - prints the contents of the eeprom in a human-readable
445 eeprom update - allows user to update eeprom fields by specifying
454 - override to provide your own layout name parsing
457 - override to setup the layout metadata based on the version
459 - override to provide your own algorithm for detecting layout
462 - contains various printing and updating functions for common
487 bool "md5sum -v"
491 Add -v option to verify data against an MD5 checksum.
503 md - memory display
504 mm - memory modify (auto-incrementing address)
505 nm - memory modify (constant address)
506 mw - memory write (fill)
507 cp - memory copy
508 cmp - memory compare
509 base - print or set address offset
510 loop - initialize loop on address range
520 mdc - memory display cyclic
521 mwc - memory write cyclic
530 bool "sha1sum -v"
533 Add -v option to verify data against a SHA1 checksum.
536 bool "strings - display strings in memory"
568 Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm)
575 Uncompress a zip-compressed memory region.
593 bool "clk - Show clock frequencies"
598 clock values from associated drivers. However currently no command
602 bool "demo - Demonstration commands for driver model"
606 driver model. To use this properly you will need to enable one or
610 option is to use sandbox and pass the -d point to sandbox's
611 u-boot.dtb file.
617 Enables the command "dfu" which is used to have U-Boot create a DFU
623 bool "dm - Access to driver model information"
634 bool "fdcboot - Boot from floppy device"
643 flinfo - print FLASH memory information
644 erase - FLASH memory
645 protect - enable or disable FLASH write protection
654 bool "fpga loadbp - load partial bitstream (Xilinx only)"
661 bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)"
667 bool "fpga loadmk - load bitstream from image"
673 bool "fpga loadp - load partial bitstream"
680 bool "fpgad - dump FPGA registers"
683 Provides a way to dump FPGA registers by calling the board-specific
688 bool "fuse - support for the fuse subssystem"
690 (deprecated - needs conversion to driver model)
692 which control the behaviour of the device. The command uses the
706 Enable the 'gpt' command to ready and write GPT style partition
712 Enable the generation of partitions with random UUIDs if none
724 bool "ide - Support for IDE drivers"
733 bool "io - Support for performing I/O accesses"
741 bool "iotrace - Support for tracing I/O activity"
765 For now no commands are provided to examine the trace buffer. The
769 contents do not change outside of software control. Where this is not
789 Load an S-Record file over serial line
893 bool "mmc_spi - Set up MMC SPI device"
902 bool "onenand - access to onenand device"
917 bool "pci - Access PCI devices"
921 peripherals. Sub-commands allow bus enumeration, displaying and
925 bool "pinit - Set up PCMCIA device"
930 cards using a standard 68-pin connector.
933 bool "read - Read binary data from a partition"
935 Provides low-level access to the data in a partition.
941 Support for Remote Processor control
944 bool "rockusb - Command to upgrade Rockchip device"
949 Bulk-Only Transport based on UMS framework.
971 bool "sata - Access SATA subsystem"
984 bool "saves - Save a file over serial in S-Record format"
986 Provides a way to save a binary file using the Motorola S-Record
990 bool "sdram - Print SDRAM configuration information"
1002 bool "sf test - Allow testing of SPI flash"
1009 equal the SPI bus speed for a single-bit-wide SPI bus, assuming
1018 bool "tsi148 - Command to access tsi148 device"
1020 This provides various sub-commands to initialise and configure the
1024 bool "Enable UFS - Universal Flash Subsystem commands"
1031 bool "universe - Command to set up the Turndra Universe controller"
1045 Enables the command "sdp" which is used to have U-Boot emulating the
1100 bootp - boot image via network using BOOTP/TFTP protocol
1101 tftpboot - boot image via network using TFTP protocol
1154 Enable MII utility commands.
1179 Acquire a network IP address using the link-local protocol
1184 Allow control of L2 Ethernet switch commands. These are supported
1185 by the vsc9953 Ethernet driver at present. Sub-commands allow
1196 bool "Enable 'bmp' command"
1199 This provides a way to obtain information about a BMP-format iamge
1208 bool "Enable board-specific commands"
1212 Some boards have board-specific commands which are only enabled
1214 option provides a way to control this. The commands that are enabled
1218 bool "mmc bkops enable"
1222 Enable command for setting manual background operations handshake
1227 bool "blkcache - control and stats for block cache"
1231 Enable the blkcache command, which can be used to control the
1233 This is most useful when fine-tuning the operation of the cache
1240 Enable the "icache" and "dcache" commands
1243 bool "Enable the 'display' command, for character displays"
1247 displayed on a simple board-specific display. Implement
1254 Enable the 'led' command which allows for control of LEDs supported
1263 Enable the 'date' command for getting/setting the time/date in RTC
1272 bool "gettime - read elapsed time"
1274 Enable the 'gettime' command which reads the elapsed time since
1275 U-Boot started running. This shows the time in seconds and
1302 This provides basic access to the U-Boot's sound support. The main
1305 sound init - set up sound system
1306 sound play - play a sound
1313 feature is to allow easy loading of files passed to qemu-system
1314 via -kernel / -initrd
1319 bool "terminal - provides a way to attach a serial terminal"
1321 Provides a 'cu'-like serial terminal command. This can be used to
1323 is very simple with no special processing of characters. As with
1327 bool "uuid, guid - generation of unique IDs"
1331 uuid - generate random Universally Unique Identifier
1332 guid - generate Globally Unique Identifier based on random UUID
1340 bool "Enable the 'bootstage' command"
1348 bool "Enable Driver Model PMIC command"
1353 - list - list pmic devices
1354 - pmic dev <id> - show or [set] operating pmic device (NEW)
1355 - pmic dump - dump registers
1356 - pmic read address - read byte of register at address
1357 - pmic write address - write byte to register at address
1361 bool "Enable Driver Model REGULATOR command"
1364 This command is based on driver model regulator's API.
1366 - list - list regulator devices
1367 - regulator dev <id> - show or [set] operating regulator device
1368 - regulator info - print constraints info
1369 - regulator status - print operating status
1370 - regulator value <val] <-f> - print/[set] voltage value [uV]
1371 - regulator current <val> - print/[set] current value [uA]
1372 - regulator mode <id> - print/[set] operating mode id
1373 - regulator enable - enable the regulator output
1374 - regulator disable - disable the regulator output
1376 The '-f' (force) option can be used for set the value which exceeds
1377 the limits, which are found in device-tree and are kept in regulator's
1381 bool "Enable Driver Model Charge Display command"
1385 Support U-Boot charge display.
1388 bool "Enable Driver Model DVFS command"
1394 - dvfs - apply dvfs policy once
1395 - dvfs repeat - repeat apply dvfs policy until achieve the target temperature
1401 bool "Enable the 'aes' command"
1411 bool "Enable the 'blob' command"
1415 Freescale's SEC block has built-in Blob Protocol which provides
1416 a method for protecting user-defined data across system power
1424 from SoC's non-volatile secret key and a 16 bit Key identifier.
1426 blob. The non-volatile secure key is available for use only during
1432 Sub-commands:
1433 blob enc - encapsulating data as a cryptgraphic blob
1434 blob dec - decapsulating cryptgraphic blob to get the data
1464 bool "hash -v"
1467 Add -v option to verify data against a hash.
1470 bool "Enable the 'tpm' command"
1474 range of commands if provided - see 'tpm help' for details. The
1479 bool "Enable the 'tpm test' command"
1483 correctly. The tests cover initialisation, non-volatile RAM, extend,
1492 bool "Enable crosec command"
1496 Enable command-line access to the Chrome OS EC (Embedded
1498 a number of sub-commands for performing EC tasks such as
1505 bool "Enable the 'cbfs' command"
1508 Define this to enable support for reading from a Coreboot
1509 filesystem. This is a ROM-based filesystem used for accessing files
1510 on systems that use coreboot as the first boot-loader and then load
1511 U-Boot to actually boot the Operating System. Available commands are
1515 bool "Enable the 'cramfs' command"
1522 cramfsls - lists files in a cramfs image
1523 cramfsload - loads a file from a cramfs image
1605 This enables the 'spread' sub-command of the mtdparts command.
1612 bool "reiser - Access to reiserfs filesystems"
1617 reiserls - list files
1618 reiserload - load a file
1621 bool "scsi - Access to SCSI devices"
1630 bool "yaffs2 - Access of YAFFS2 filesystem"
1636 for NAND flash. It incorporates bad-block management and ensures
1641 bool "zfs - Access of ZFS filesystem"
1644 on Solaris systems. Two sub-commands are provided:
1646 zfsls - list files in a directory
1647 zfsload - load a file
1656 bool "atags - Dump all rockchip atags"
1669 bool "diag - Board diagnostics"
1672 called Power-on Self Tests (POST). The command allows listing of
1677 bool "irq - Show information about interrupts"
1682 interrupts - enable or disable interrupts
1683 irqinfo - print device-specific interrupt information
1686 bool "kgdb - Allow debugging of U-Boot with gdb"
1688 This enables a 'kgdb' command which allows gdb to connect to U-Boot
1690 single-stepping, inspecting variables, etc. This is supported only
1694 bool "log - Generation, control and access to logging"
1702 bool "trace - Support tracing of function calls and timing"
1704 Enables a command to control using of function tracing within
1705 U-Boot. This allows recording of call traces including timing
1713 tristate "Enable UBI - Unsorted block images commands"
1719 UBI is a software layer above MTD layer which admits use of LVM-like
1723 (www.linux-mtd.infradead.org). Activate this option if you want
1724 to use U-Boot UBI commands.
1727 tristate "Enable UBIFS - Unsorted block images filesystem commands"