arm/dts/sun7i-a20-olinuxino-micro.dts

4  * Maxime Ripard <maxime.ripard@free-electrons.com>
6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
46 #include "sun7i-a20.dtsi"
47 #include "sunxi-common-regulators.dtsi"
49 #include <dt-bindings/gpio/gpio.h>
50 #include <dt-bindings/input/input.h>
51 #include <dt-bindings/interrupt-controller/irq.h>
52 #include <dt-bindings/pinctrl/sun4i-a10.h>
55 	model = "Olimex A20-Olinuxino Micro";
56 	compatible = "olimex,a20-olinuxino-micro", "allwinner,sun7i-a20";
67 		stdout-path = "serial0:115200n8";
71 		compatible = "gpio-leds";
72 		pinctrl-names = "default";
73 		pinctrl-0 = <&led_pins_olinuxino>;
76 			label = "a20-olinuxino-micro:green:usr";
78 			default-state = "on";
84 	target-supply = <&reg_ahci_5v>;
97 	pinctrl-names = "default";
98 	pinctrl-0 = <&gmac_pins_mii_a>;
100 	phy-mode = "mii";
103 	phy1: ethernet-phy@1 {
109 	pinctrl-names = "default";
110 	pinctrl-0 = <&i2c0_pins_a>;
114 		compatible = "x-powers,axp209";
116 		interrupt-parent = <&nmi_intc>;
119 		interrupt-controller;
120 		#interrupt-cells = <1>;
125 	pinctrl-names = "default";
126 	pinctrl-0 = <&i2c1_pins_a>;
137 	pinctrl-names = "default";
138 	pinctrl-0 = <&i2c2_pins_a>;
143 	vref-supply = <&reg_vcc3v0>;
197 	pinctrl-names = "default";
198 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
199 	vmmc-supply = <&reg_vcc3v3>;
200 	bus-width = <4>;
201 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
202 	cd-inverted;
207 	pinctrl-names = "default";
208 	pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olinuxinom>;
209 	vmmc-supply = <&reg_vcc3v3>;
210 	bus-width = <4>;
211 	cd-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
212 	cd-inverted;
275 	pinctrl-names = "default";
276 	pinctrl-0 = <&spi1_pins_a>,
282 	pinctrl-names = "default";
283 	pinctrl-0 = <&spi2_pins_a>,
289 	pinctrl-names = "default";
290 	pinctrl-0 = <&uart0_pins_a>;
295 	pinctrl-names = "default";
296 	pinctrl-0 = <&uart6_pins_a>;
301 	pinctrl-names = "default";
302 	pinctrl-0 = <&uart7_pins_a>;
312 	pinctrl-names = "default";
313 	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
314 	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
315 	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
316 	usb0_vbus-supply = <&reg_usb0_vbus>;
317 	usb1_vbus-supply = <&reg_usb1_vbus>;
318 	usb2_vbus-supply = <&reg_usb2_vbus>;