arm/dts/sun5i-a10s-olinuxino-micro.dts

4  * Maxime Ripard <maxime.ripard@free-electrons.com>
6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
46 #include "sun5i-a10s.dtsi"
47 #include "sunxi-common-regulators.dtsi"
49 #include <dt-bindings/gpio/gpio.h>
50 #include <dt-bindings/input/input.h>
51 #include <dt-bindings/pinctrl/sun4i-a10.h>
54 	model = "Olimex A10s-Olinuxino Micro";
55 	compatible = "olimex,a10s-olinuxino-micro", "allwinner,sun5i-a10s";
64 		stdout-path = "serial0:115200n8";
68 		compatible = "gpio-leds";
69 		pinctrl-names = "default";
70 		pinctrl-0 = <&led_pins_olinuxino>;
73 			label = "a10s-olinuxino-micro:green:usr";
75 			default-state = "on";
85 	pinctrl-names = "default";
86 	pinctrl-0 = <&emac_pins_a>;
96 	pinctrl-names = "default";
97 	pinctrl-0 = <&i2c0_pins_a>;
109 	pinctrl-names = "default";
110 	pinctrl-0 = <&i2c1_pins_a>;
117 		read-only;
122 	pinctrl-names = "default";
123 	pinctrl-0 = <&i2c2_pins_a>;
128 	vref-supply = <&reg_vcc3v0>;
131 	button@191 {
138 	button@392 {
145 	button@601 {
152 	button@795 {
159 	button@987 {
170 	phy1: ethernet-phy@1 {
176 	pinctrl-names = "default";
177 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>;
178 	vmmc-supply = <&reg_vcc3v3>;
179 	bus-width = <4>;
180 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
181 	cd-inverted;
186 	pinctrl-names = "default";
187 	pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>;
188 	vmmc-supply = <&reg_vcc3v3>;
189 	bus-width = <4>;
190 	cd-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
191 	cd-inverted;
246 	pinctrl-0 = <&usb1_vbus_pin_olinuxino_m>;
252 	pinctrl-names = "default";
253 	pinctrl-0 = <&spi2_pins_a>,
259 	pinctrl-names = "default";
260 	pinctrl-0 = <&uart0_pins_a>;
265 	pinctrl-names = "default";
266 	pinctrl-0 = <&uart2_pins_a>;
271 	pinctrl-names = "default";
272 	pinctrl-0 = <&uart3_pins_a>;
286 	pinctrl-names = "default";
287 	pinctrl-0 = <&usb0_id_detect_pin>;
288 	usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
289 	usb0_vbus-supply = <&reg_usb0_vbus>;
290 	usb1_vbus-supply = <&reg_usb1_vbus>;