arm/dts/sun4i-a10-pcduino.dts

5  * This file is dual-licensed: you can use it either under the terms
44 /dts-v1/;
45 #include "sun4i-a10.dtsi"
46 #include "sunxi-common-regulators.dtsi"
48 #include <dt-bindings/gpio/gpio.h>
49 #include <dt-bindings/input/input.h>
50 #include <dt-bindings/pinctrl/sun4i-a10.h>
54 	compatible = "linksprite,a10-pcduino", "allwinner,sun4i-a10";
61 		stdout-path = "serial0:115200n8";
65 		compatible = "gpio-leds";
66 		pinctrl-names = "default";
67 		pinctrl-0 = <&led_pins_pcduino>;
71 			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
74 		rx {
75 			label = "pcduino:green:rx";
76 			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
81 		compatible = "gpio-keys";
82 		pinctrl-names = "default";
83 		pinctrl-0 = <&key_pins_pcduino>;
84 		#address-cells = <1>;
85 		#size-cells = <0>;
90 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
96 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
102 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
108 	cpu-supply = <&reg_dcdc2>;
120 	pinctrl-names = "default";
121 	pinctrl-0 = <&emac_pins_a>;
131 	pinctrl-names = "default";
132 	pinctrl-0 = <&i2c0_pins_a>;
144 	phy1: ethernet-phy@1 {
150 	pinctrl-names = "default";
151 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
152 	vmmc-supply = <&reg_vcc3v3>;
153 	bus-width = <4>;
154 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
155 	cd-inverted;
197 	regulator-always-on;
198 	regulator-min-microvolt = <1000000>;
199 	regulator-max-microvolt = <1400000>;
200 	regulator-name = "vdd-cpu";
204 	regulator-always-on;
205 	regulator-min-microvolt = <1000000>;
206 	regulator-max-microvolt = <1400000>;
207 	regulator-name = "vdd-int-dll";
211 	regulator-name = "vdd-rtc";
215 	regulator-always-on;
216 	regulator-min-microvolt = <3000000>;
217 	regulator-max-microvolt = <3000000>;
218 	regulator-name = "avcc";
222 	pinctrl-names = "default";
223 	pinctrl-0 = <&uart0_pins_a>;
233 	pinctrl-names = "default";
234 	pinctrl-0 = <&usb0_id_detect_pin>;
235 	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
236 	usb1_vbus-supply = <&reg_vcc5v0>; /* USB1 VBUS is always on */
237 	usb2_vbus-supply = <&reg_vcc5v0>; /* USB2 VBUS is always on */