arm/dts/rk3288-tinker.dtsi

2  * This file is dual-licensed: you can use it either under the terms
42 #include "rk3288-u-boot.dtsi"
50 	ext_gmac: external-gmac-clock {
51 		compatible = "fixed-clock";
52 		clock-frequency = <125000000>;
53 		clock-output-names = "ext_gmac";
54 		#clock-cells = <0>;
57 	gpio-keys {
58 		compatible = "gpio-keys";
59 		#address-cells = <1>;
60 		#size-cells = <0>;
63 		pinctrl-names = "default";
64 		pinctrl-0 = <&pwrbtn>;
69 			linux,input-type = <1>;
70 			gpio-key,wakeup = <1>;
71 			debounce-interval = <100>;
75 	gpio-leds {
76 		compatible = "gpio-leds";
78 		pwr-led {
80 			linux,default-trigger = "default-on";
83 		act-led {
85 			linux,default-trigger="mmc0";
89 	vcc_sys: vsys-regulator {
90 		compatible = "regulator-fixed";
91 		regulator-name = "vcc_sys";
92 		regulator-min-microvolt = <5000000>;
93 		regulator-max-microvolt = <5000000>;
94 		regulator-always-on;
95 		regulator-boot-on;
103 	vcc_sd: sdmmc-regulator {
104 		compatible = "regulator-fixed";
106 		pinctrl-names = "default";
107 		pinctrl-0 = <&sdmmc_pwr>;
108 		regulator-name = "vcc_sd";
109 		regulator-min-microvolt = <3300000>;
110 		regulator-max-microvolt = <3300000>;
111 		startup-delay-us = <100000>;
112 		vin-supply = <&vcc_io>;
115 	vcc5v0_host: usb-host-regulator {
116 		compatible = "regulator-fixed";
117 		enable-active-high;
119 		pinctrl-names = "default";
120 		pinctrl-0 = <&host_vbus_drv>;
121 		regulator-name = "vcc5v0_host";
122 		regulator-min-microvolt = <5000000>;
123 		regulator-max-microvolt = <5000000>;
124 		regulator-always-on;
129 	cpu0-supply = <&vdd_cpu>;
133 	bus-width = <4>;
134 	cap-mmc-highspeed;
135 	cap-sd-highspeed;
136 	card-detect-delay = <200>;
137 	disable-wp;			/* wp not hooked up */
138 	num-slots = <1>;
139 	pinctrl-names = "default";
140 	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
142 	supports-sd;
143 	vmmc-supply = <&vcc_sd>;
144 	vqmmc-supply = <&vccio_sd>;
148 	mali-supply = <&vdd_gpu>;
153 	phy-supply = <&vcc33_lan>;
154 	phy-mode = "rgmii";
156 	snps,reset-gpio = <&gpio4 7 0>;
157 	snps,reset-active-low;
158 	snps,reset-delays-us = <0 10000 1000000>;
159 	assigned-clocks = <&cru SCLK_MAC>;
160 	assigned-clock-parents = <&ext_gmac>;
161 	pinctrl-names = "default";
162 	pinctrl-0 = <&rgmii_pins>;
169 	ddc-i2c-bus = <&i2c5>;
175 	clock-frequency = <400000>;
180 		interrupt-parent = <&gpio0>;
182 		pinctrl-names = "default";
183 		pinctrl-0 = <&pmic_int &global_pwroff>;
184 		rockchip,system-power-controller;
185 		wakeup-source;
186 		#clock-cells = <1>;
187 		clock-output-names = "xin32k", "rk808-clkout2";
189 		vcc1-supply = <&vcc_sys>;
190 		vcc2-supply = <&vcc_sys>;
191 		vcc3-supply = <&vcc_sys>;
192 		vcc4-supply = <&vcc_sys>;
193 		vcc6-supply = <&vcc_sys>;
194 		vcc7-supply = <&vcc_sys>;
195 		vcc8-supply = <&vcc_18>;
196 		vcc9-supply = <&vcc_io>;
197 		vcc10-supply = <&vcc_io>;
198 		vcc11-supply = <&vcc_sys>;
199 		vcc12-supply = <&vcc_io>;
200 		vddio-supply = <&vcc18_ldo1>;
204 				regulator-always-on;
205 				regulator-boot-on;
206 				regulator-min-microvolt = <750000>;
207 				regulator-max-microvolt = <1350000>;
208 				regulator-name = "vdd_arm";
209 				regulator-state-mem {
210 					regulator-off-in-suspend;
215 				regulator-always-on;
216 				regulator-boot-on;
217 				regulator-min-microvolt = <850000>;
218 				regulator-max-microvolt = <1250000>;
219 				regulator-name = "vdd_gpu";
220 				regulator-state-mem {
221 					regulator-on-in-suspend;
222 					regulator-suspend-microvolt = <1000000>;
227 				regulator-always-on;
228 				regulator-boot-on;
229 				regulator-name = "vcc_ddr";
230 				regulator-state-mem {
231 					regulator-on-in-suspend;
236 				regulator-always-on;
237 				regulator-boot-on;
238 				regulator-min-microvolt = <3300000>;
239 				regulator-max-microvolt = <3300000>;
240 				regulator-name = "vcc_io";
241 				regulator-state-mem {
242 					regulator-on-in-suspend;
243 					regulator-suspend-microvolt = <3300000>;
248 				regulator-always-on;
249 				regulator-boot-on;
250 				regulator-min-microvolt = <1800000>;
251 				regulator-max-microvolt = <1800000>;
252 				regulator-name = "vcc18_ldo1";
253 				regulator-state-mem {
254 					regulator-on-in-suspend;
255 					regulator-suspend-microvolt = <1800000>;
260 				regulator-always-on;
261 				regulator-boot-on;
262 				regulator-min-microvolt = <3300000>;
263 				regulator-max-microvolt = <3300000>;
264 				regulator-name = "vcc33_mipi";
265 				regulator-state-mem {
266 					regulator-off-in-suspend;
271 				regulator-always-on;
272 				regulator-boot-on;
273 				regulator-min-microvolt = <1000000>;
274 				regulator-max-microvolt = <1000000>;
275 				regulator-name = "vdd_10";
276 				regulator-state-mem {
277 					regulator-on-in-suspend;
278 					regulator-suspend-microvolt = <1000000>;
283 				regulator-always-on;
284 				regulator-boot-on;
285 				regulator-min-microvolt = <1800000>;
286 				regulator-max-microvolt = <1800000>;
287 				regulator-name = "vcc18_codec";
288 				regulator-state-mem {
289 					regulator-on-in-suspend;
290 					regulator-suspend-microvolt = <1800000>;
295 				regulator-always-on;
296 				regulator-boot-on;
297 				regulator-min-microvolt = <1800000>;
298 				regulator-max-microvolt = <3300000>;
299 				regulator-name = "vccio_sd";
300 				regulator-state-mem {
301 					regulator-on-in-suspend;
302 					regulator-suspend-microvolt = <3300000>;
307 				regulator-always-on;
308 				regulator-boot-on;
309 				regulator-min-microvolt = <1000000>;
310 				regulator-max-microvolt = <1000000>;
311 				regulator-name = "vdd10_lcd";
312 				regulator-state-mem {
313 					regulator-on-in-suspend;
314 					regulator-suspend-microvolt = <1000000>;
319 				regulator-always-on;
320 				regulator-boot-on;
321 				regulator-min-microvolt = <1800000>;
322 				regulator-max-microvolt = <1800000>;
323 				regulator-name = "vcc_18";
324 				regulator-state-mem {
325 					regulator-on-in-suspend;
326 					regulator-suspend-microvolt = <1800000>;
331 				regulator-always-on;
332 				regulator-boot-on;
333 				regulator-min-microvolt = <1800000>;
334 				regulator-max-microvolt = <1800000>;
335 				regulator-name = "vcc18_lcd";
336 				regulator-state-mem {
337 					regulator-on-in-suspend;
338 					regulator-suspend-microvolt = <1800000>;
343 				regulator-always-on;
344 				regulator-boot-on;
345 				regulator-name = "vcc33_sd";
346 				regulator-state-mem {
347 					regulator-on-in-suspend;
352 				regulator-always-on;
353 				regulator-boot-on;
354 				regulator-name = "vcc33_lan";
355 				regulator-state-mem {
356 					regulator-on-in-suspend;
367 		#sound-dai-cells = <0>;
369 		interrupt-parent = <&gpio6>;
371 		nuvoton,jkdet-enable = <1>;
372 		nuvoton,jkdet-pull-enable = <1>;
373 		nuvoton,jkdet-pull-up = <0>;
374 		nuvoton,jkdet-polarity = <1>;
375 		nuvoton,vref-impedance = <2>;
376 		nuvoton,micbias-voltage = <6>;
377 		nuvoton,sar-threshold-num = <4>;
378 		nuvoton,sar-threshold = <0xa 0x14 0x26 0x73>;
379 		nuvoton,sar-hysteresis = <0>;
380 		nuvoton,sar-voltage = <6>;
381 		nuvoton,sar-compare-time = <0>;
382 		nuvoton,sar-sampling-time = <0>;
383 		nuvoton,short-key-debounce = <3>;
384 		nuvoton,jack-insert-debounce = <7>;
385 		nuvoton,jack-eject-debounce = <7>;
386 		clock-names = "mclk";
404 	vref-supply = <&vcc18_ldo1>;
429 	rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
430 	rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
467 	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
468 		drive-strength = <8>;
471 	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
472 		bias-pull-up;
473 		drive-strength = <8>;
477 		bl_en: bl-en {
489 		eth_phy_pwr: eth-phy-pwr {
495 		pmic_int: pmic-int {
503 		 * high-speed mode on EVB board so bump up to 8ma.
505 		sdmmc_bus4: sdmmc-bus4 {
512 		sdmmc_clk: sdmmc-clk {
516 		sdmmc_cmd: sdmmc-cmd {
520 		sdmmc_pwr: sdmmc-pwr {
526 		host_vbus_drv: host-vbus-drv {
530 		pwr_3g: pwr-3g {