arm/dts/meson-gxbb-odroidc2.dts

6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
47 #include "meson-gxbb.dtsi"
48 #include <dt-bindings/gpio/gpio.h>
51 	compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
52 	model = "Hardkernel ODROID-C2";
59 		stdout-path = "serial0:115200n8";
67 	usb_otg_pwr: regulator-usb-pwrs {
68 		compatible = "regulator-fixed";
70 		regulator-name = "USB_OTG_PWR";
72 		regulator-min-microvolt = <5000000>;
73 		regulator-max-microvolt = <5000000>;
76 		enable-active-high;
80 		compatible = "gpio-leds";
84 			linux,default-trigger = "heartbeat";
85 			default-state = "off";
89 	tflash_vdd: regulator-tflash_vdd {
93 		compatible = "regulator-fixed";
95 		regulator-name = "TFLASH_VDD";
96 		regulator-min-microvolt = <3300000>;
97 		regulator-max-microvolt = <3300000>;
100 		enable-active-high;
103 	tf_io: gpio-regulator-tf_io {
104 		compatible = "regulator-gpio";
106 		regulator-name = "TF_IO";
107 		regulator-min-microvolt = <1800000>;
108 		regulator-max-microvolt = <3300000>;
114 		gpios-states = <0>;
120 	vcc1v8: regulator-vcc1v8 {
121 		compatible = "regulator-fixed";
122 		regulator-name = "VCC1V8";
123 		regulator-min-microvolt = <1800000>;
124 		regulator-max-microvolt = <1800000>;
127 	vcc3v3: regulator-vcc3v3 {
128 		compatible = "regulator-fixed";
129 		regulator-name = "VCC3V3";
130 		regulator-min-microvolt = <3300000>;
131 		regulator-max-microvolt = <3300000>;
134 	emmc_pwrseq: emmc-pwrseq {
135 		compatible = "mmc-pwrseq-emmc";
136 		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
146 	pinctrl-0 = <&uart_ao_a_pins>;
147 	pinctrl-names = "default";
152 	pinctrl-0 = <&eth_rgmii_pins>;
153 	pinctrl-names = "default";
154 	phy-handle = <&eth_phy0>;
155 	phy-mode = "rgmii";
157 	snps,reset-gpio = <&gpio GPIOZ_14 0>;
158 	snps,reset-delays-us = <0 10000 1000000>;
159 	snps,reset-active-low;
161 	amlogic,tx-delay-ns = <2>;
164 		compatible = "snps,dwmac-mdio";
165 		#address-cells = <1>;
166 		#size-cells = <0>;
168 		eth_phy0: ethernet-phy@0 {
170 			eee-broken-1000t;
176 	gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
184 	gpio-line-names = /* Bank GPIOZ */
228 	pinctrl-0 = <&remote_input_ao_pins>;
229 	pinctrl-names = "default";
234 	pinctrl-0 = <&i2c_a_pins>;
235 	pinctrl-names = "default";
240 	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
245 	usb-hub {
246 		gpio-hog;
248 		output-high;
249 		line-name = "usb-hub-reset";
255 	phy-supply = <&usb_otg_pwr>;
272 	vref-supply = <&vcc1v8>;
278 	pinctrl-0 = <&sdcard_pins>;
279 	pinctrl-names = "default";
281 	bus-width = <4>;
282 	cap-sd-highspeed;
283 	max-frequency = <100000000>;
284 	disable-wp;
286 	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
287 	cd-inverted;
289 	vmmc-supply = <&tflash_vdd>;
290 	vqmmc-supply = <&tf_io>;
296 	pinctrl-0 = <&emmc_pins>;
297 	pinctrl-names = "default";
299 	bus-width = <8>;
300 	cap-sd-highspeed;
301 	max-frequency = <200000000>;
302 	non-removable;
303 	disable-wp;
304 	cap-mmc-highspeed;
305 	mmc-ddr-1_8v;
306 	mmc-hs200-1_8v;
308 	mmc-pwrseq = <&emmc_pwrseq>;
309 	vmmc-supply = <&vcc3v3>;
310 	vqmmc-supply = <&vcc1v8>;