README_MLAN - OpenGrok cross reference for /OK3568_Linux_fs/kernel/drivers/net/wireless/nxp/README_MLAN

2123 	This command is used to enable/disable auto TDLS.
2133 		mlanutl mlan0 autotdls 1         : enable auto TDLS
2134 		mlanutl mlan0 autotdls 0         : disable auto TDLS
2138 …This command is used to set/get TDLS idle timeout. The valid value is between 0-0xffff. When set t…
2144 		TDLS idle timeout value
2594 		mlanutl mlan0 extcapcfg 0x0000008020	: Set TDLS support and Interworking bits.
2958 			 : Bit 9 - TDLS support indication enable/disable
2965 …mlanutl mlan0 hotspotcfg 0x301  : Turn on HotSpot2.0 and enable TDLS support and interworking indi…
2966 …mlanutl mlan0 hotspotcfg 0      : Turn off HotSpot2.0 and disable TDLS support and interworking in…
4041 	This command is used to send TDLS channel switch request.
4047 		tdls.conf: The configuration file for sending TDLS channel switch command.
4051 			: Send TDLS channel switch command, based on the configuration file.
4054 	This command is used to enable/disable TDLS on device.
4060 		0: Enable TDLS.
4061 		1: Disable TDLS.
4064 		mlanutl mlan0 tdls_config 0      : Disable TDLS
4065 		mlanutl mlan0 tdls_config 1      : Enable TDLS
4068 	This command is used to set TDLS channel switch params
4074 		tdls.conf: The configuration file specifying the TDLS channel switch params.
4078 			: Set TDLS channel switch params, based on the configuration file.
4084 	This command is used to disable TDLS channel switch
4090 		tdls.conf: The configuration file to disable TDLS channel switch.
4094 			: Disable TDLS channel switch, based on the configuration file.
4097 	This command is used to request TDLS discovery.
4103 		tdls.conf: The configuration file to request TDLS discovery.
4107 			: Request TDLS discovery based on the configuration file.
4110 	This command is used to get link information about TDLS links or
4111     a TDLS link correponding to peer mac address.
4117 		tdls.conf: The configuration file to send TDLS command to get current link status.
4121 			: Send TDLS command to get current link status based on the configuration file.
4124 	This command is used to send TDLS powermode request.
4130 		tdls.conf: The configuration file for sending TDLS powermode command.
4134 			: Send TDLS powermode (either 0:Active, 1:PowerSave) command, based on the configuration file.
4137 	This command is used for setting the capabilities of the TDLS station.
4143 		tdls.conf: The configuration file specifying the capabilities of the TDLS station.
4147 			: Set capabilities of the TDLS station, based on the configuration file.
4150 	This command is used to send TDLS setup request.
4156 		tdls.conf: The configuration file for sending TDLS setup request.
4160 			: Send TDLS setup request, based on the configuration file.
4163 	This command is used to send stop TDLS channel switch request.
4169 		tdls.conf: The configuration file for sending stop TDLS channel switch command.
4173 			: Send stop TDLS channel switch command, based on the configuration file.
4176 	This command is used to send TDLS teardown request.
4182 		tdls.conf: The configuration file for requesting teardown of TDLS link.
4186 			: Request teardown of TDLS link, based on the configuration file.
4233 	This command is used to enable/disable TX AMPDU on infra link when TDLS link is established
4247 		The set command only works when TDLS link is established.