Lines Matching refs:STA
20 Bit 0 : STA
24 max_sta_bss: Maximum number of STA BSS (default 1, max 1)
25 sta_name: Name of the STA interface (default: "mlan")
31 uap_oper_ctrl: uAP operation control when in-STA disconnect with ext-AP
94 Bit 0: STA WEXT
96 Bit 2: STA CFG80211
130 uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 64)
155 multicase_count = <multicast address count> // Only for STA
156 essid = <current SSID> // Only for STA
157 bssid = <current BSSID> // Only for STA
158 channel = <current channel> // Only for STA
159 region_code = <current region code> // Only for STA
160 multicast_address[n] = <multicast address> // Only for STA
204 is_deep_sleep = <0/1, not deep sleep state/deep sleep state> // Only for STA
210 pps_uapsd_mode = <0/1, PPS/UAPSD mode disabled/enabled> // Only for STA
211 sleep_pd = <sleep period in milliseconds> // Only for STA
212 qos_cfg = <WMM QoS info> // Only for STA
213 tx_lock_flag = <0/1, Tx lock flag> // Only for STA
214 port_open = <0/1, port open flag> // Only for STA
215 scan_processing = <0/1, scan processing flag> // Only for STA
236 num_evt_deauth = <number of deauthenticated events received from device> // Only for STA
237 num_evt_disassoc = <number of disassociated events received from device> // Only for STA
238 num_evt_link_lost = <number of link lost events received from device> // Only for STA
239 num_cmd_deauth = <number of deauthenticate commands sent to device> // Only for STA
240 num_cmd_assoc_ok = <number of associate commands with success return> // Only for STA
241 num_cmd_assoc_fail = <number of associate commands with failure return> // Only for STA
961 Note: This command is available only when STA is connected.
987 Note: This command is available only when STA is connected.
1021 Note: This command is available only when STA is connected.
1176 1: configuration of VHT capabilities for Tx operations (STA only)
1177 2: configuration of VHT capabilities for association (STA only)
1179 Note: For the STA, the VHT capabilities configuration is applied in association,
1208 0: no feedback of VHT MFB from the STA
1209 1: unsolicted feedback of VHT MFB from the STA
1211 from the STA
1247 …Note: for the STA, if <txrx> is 1 (Tx operations), the bitmap for <vhtcap> may be simplied as foll…
1256 …<tx_mcs_map> - This parameter specifies the TX MCS map. It may not be used for the STA if <txrx> i…
1269 …<rx_mcs_map> - This parameter specifies the RX MCS map. It may not be used for the STA if <txrx> i…
1278 mlanutl mlan0 vhtcfg 2 1 : Get current VHT configuration in 5GHz for the STA.
1279 mlanutl mlan0 vhtcfg 2 2 : Get maximum VHT configuration in 5GHz for the STA.
1281 : Set the Tx operations configuration in 5GHz for the STA,
1284 : Set the VHT capabilities configuration in 5GHz for the STA,
1435 …his subcmd applies to uapX only. uAP uses it to manage the RTS/CTS used by associated non-AP HE STA
1452 …did not indicate tolerance to narrow bandwidth RU in OFDMA before the STA transmits an HE TB PPDU …
2214 0 : STA
2540 1 - driver disable DFS master when AP and STA operate in same DFS channel
2913 Note: The configuration set should be issued when STA is disconnected.
3052 1: - STA can respond to a calibration request using
3055 3: - STA can both initiate and respond to a calibration request
3075 0: - no grouping (STA supports groups of 1)
3354 STA/AP is disconnected. For in-channel sniffer mode, the configuration
3355 can be issued irrespective of the STA/AP connected state, and requires
3356 specification of only action and filter parameters. If any of the STA/AP
3400 After this can only use sniffer mode, don't make STA/P2P/UAP work.
3768 this bit is only used with STA BSS
4324 <nss> - This parameter specifies the nss that the STA can receive.
4752 when in STA mode, or before starting bss when in uAP mode
4862 DOT11MC FTM frames exchanges in un-associated state for STA or uAP
4922 2: STA