boot/dts/sun8i-a33-sinlinx-sina33.dts

2  * Copyright 2015 Chen-Yu Tsai
4  * Chen-Yu Tsai <wens@csie.org>
6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
46 #include "sun8i-a33.dtsi"
47 #include "sunxi-common-regulators.dtsi"
49 #include <dt-bindings/gpio/gpio.h>
50 #include <dt-bindings/input/input.h>
54 	compatible = "sinlinx,sina33", "allwinner,sun8i-a33";
61 		stdout-path = "serial0:115200n8";
65 		compatible = "netron-dy,e231732";
69 				remote-endpoint = <&tcon0_out_panel>;
80 	cpu-supply = <&reg_dcdc3>;
84 	opp-1104000000 {
85 		opp-hz = /bits/ 64 <1104000000>;
86 		opp-microvolt = <1320000>;
87 		clock-latency-ns = <244144>; /* 8 32k periods */
90 	opp-1200000000 {
91 		opp-hz = /bits/ 64 <1200000000>;
92 		opp-microvolt = <1320000>;
93 		clock-latency-ns = <244144>; /* 8 32k periods */
110 	vref-supply = <&reg_dcdc1>;
113 	button-200 {
120 	button-400 {
127 	button-600 {
136 	vmmc-supply = <&reg_dcdc1>;
137 	bus-width = <4>;
138 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
143 	pinctrl-names = "default";
144 	pinctrl-0 = <&mmc2_8bit_pins>;
145 	vmmc-supply = <&reg_dcdc1>;
146 	bus-width = <8>;
147 	non-removable;
148 	cap-mmc-hw-reset;
154 	drive-strength = <40>;
165 		compatible = "x-powers,axp223";
167 		interrupt-parent = <&nmi_intc>;
169 		eldoin-supply = <&reg_dcdc1>;
184 	regulator-always-on;
185 	regulator-min-microvolt = <3000000>;
186 	regulator-max-microvolt = <3000000>;
187 	regulator-name = "vcc-io";
191 	regulator-always-on;
192 	regulator-min-microvolt = <2350000>;
193 	regulator-max-microvolt = <2650000>;
194 	regulator-name = "vdd-dll";
198 	regulator-always-on;
199 	regulator-min-microvolt = <2700000>;
200 	regulator-max-microvolt = <3300000>;
201 	regulator-name = "vcc-pll-avcc";
205 	regulator-always-on;
206 	regulator-min-microvolt = <900000>;
207 	regulator-max-microvolt = <1400000>;
208 	regulator-name = "vdd-cpus";
212 	regulator-always-on;
213 	regulator-min-microvolt = <3000000>;
214 	regulator-max-microvolt = <3000000>;
215 	regulator-name = "vcc-3v0";
219 	regulator-always-on;
220 	regulator-min-microvolt = <900000>;
221 	regulator-max-microvolt = <1400000>;
222 	regulator-name = "vdd-sys";
226 	regulator-always-on;
227 	regulator-min-microvolt = <900000>;
228 	regulator-max-microvolt = <1400000>;
229 	regulator-name = "vdd-cpu";
233 	regulator-always-on;
234 	regulator-min-microvolt = <1500000>;
235 	regulator-max-microvolt = <1500000>;
236 	regulator-name = "vcc-dram";
240 	regulator-name = "vcc-rtc";
248 	pinctrl-names = "default";
249 	pinctrl-0 = <&lcd_rgb666_pins>;
256 		remote-endpoint = <&panel_input>;
261 	pinctrl-names = "default";
262 	pinctrl-0 = <&uart0_pb_pins>;
273 	usb1_vbus-supply = <&reg_vcc5v0>; /* USB1 VBUS is always on */