Lines Matching +full:sata +full:- +full:port
11 Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or
12 super-speed USB. Other lanes are for various types of low-speed, full-speed
13 or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller
14 contains a software-configurable mux that sits between the I/O controller
17 In addition to per-lane configuration, USB 3.0 ports may require additional
18 settings on a per-board basis.
20 Pads will be represented as children of the top-level XUSB pad controller
23 PHY bindings, as described by the phy-bindings.txt file in this directory.
27 "port" is typically used to denote the physical USB receptacle. The device
28 tree binding in this document uses the term "port" to refer to the logical
30 for the USB signal, the VBUS power supply, the USB 2.0 companion port for
34 --------------------
35 - compatible: Must be:
36 - Tegra124: "nvidia,tegra124-xusb-padctl"
37 - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
38 - Tegra210: "nvidia,tegra210-xusb-padctl"
39 - Tegra186: "nvidia,tegra186-xusb-padctl"
40 - Tegra194: "nvidia,tegra194-xusb-padctl"
41 - reg: Physical base address and length of the controller's registers.
42 - resets: Must contain an entry for each entry in reset-names.
43 - reset-names: Must include the following entries:
44 - "padctl"
47 - avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V.
48 - avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V.
49 - avdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V.
50 - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V.
53 - avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V.
54 - avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V.
55 - dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V.
56 - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V.
59 - avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY
61 - avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
63 - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
64 - vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
67 - avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
69 - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
83 and sata. No extra resources are required for operation of these pads.
85 For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is
89 ---------
92 - clocks: Must contain an entry for each entry in clock-names.
93 - clock-names: Must contain the following entries:
94 - "trk": phandle and specifier referring to the USB2 tracking clock
97 ---------
100 - clocks: Must contain an entry for each entry in clock-names.
101 - clock-names: Must contain the following entries:
102 - "trk": phandle and specifier referring to the HSIC tracking clock
105 ---------
108 - clocks: Must contain an entry for each entry in clock-names.
109 - clock-names: Must contain the following entries:
110 - "pll": phandle and specifier referring to the PLLE
111 - resets: Must contain an entry for each entry in reset-names.
112 - reset-names: Must contain the following entries:
113 - "phy": reset for the PCIe UPHY block
115 SATA pad:
116 ---------
119 - resets: Must contain an entry for each entry in reset-names.
120 - reset-names: Must contain the following entries:
121 - "phy": reset for the SATA UPHY block
131 --------------------
132 - status: Defines the operation status of the PHY. Valid values are:
133 - "disabled": the PHY is disabled
134 - "okay": the PHY is enabled
135 - #phy-cells: Should be 0. Since each lane represents a single PHY, there is
137 - nvidia,function: The output function of the PHY. See below for a list of
141 - usb2: usb2-0, usb2-1, usb2-2
142 - functions: "snps", "xusb", "uart"
143 - ulpi: ulpi-0
144 - functions: "snps", "xusb"
145 - hsic: hsic-0, hsic-1
146 - functions: "snps", "xusb"
147 - pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4
148 - functions: "pcie", "usb3-ss"
149 - sata: sata-0
150 - functions: "usb3-ss", "sata"
153 - usb2: usb2-0, usb2-1, usb2-2, usb2-3
154 - functions: "snps", "xusb", "uart"
155 - hsic: hsic-0, hsic-1
156 - functions: "snps", "xusb"
157 - pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6
158 - functions: "pcie-x1", "usb3-ss", "pcie-x4"
159 - sata: sata-0
160 - functions: "usb3-ss", "sata"
163 - usb2: usb2-0, usb2-1, usb2-2, usb2-3
164 - functions: "xusb"
165 - usb3: usb3-0, usb3-1, usb3-2, usb3-3
166 - functions: "xusb"
168 Port nodes:
172 by the XUSB pad controller. Per-port configuration is only required for USB.
175 -----------
178 - status: Defines the operation status of the port. Valid values are:
179 - "disabled": the port is disabled
180 - "okay": the port is enabled
181 - mode: A string that determines the mode in which to run the port. Valid
183 - "host": for USB host mode
184 - "device": for USB device mode
185 - "otg": for USB OTG mode
188 - usb-role-switch: Boolean property to indicate that the port support OTG or
189 peripheral mode. If present, the port supports switching between USB host
191 See usb/usb-conn-gpio.txt.
194 - nvidia,internal: A boolean property whose presence determines that a port
195 is internal. In the absence of this property the port is considered to be
197 - vbus-supply: phandle to a regulator supplying the VBUS voltage.
200 -----------
203 - status: Defines the operation status of the port. Valid values are:
204 - "disabled": the port is disabled
205 - "okay": the port is enabled
206 - nvidia,internal: A boolean property whose presence determines that a port
207 is internal. In the absence of this property the port is considered to be
209 - vbus-supply: phandle to a regulator supplying the VBUS voltage.
212 -----------
215 - status: Defines the operation status of the port. Valid values are:
216 - "disabled": the port is disabled
217 - "okay": the port is enabled
220 - vbus-supply: phandle to a regulator supplying the VBUS voltage.
222 Super-speed USB ports:
223 ----------------------
226 - status: Defines the operation status of the port. Valid values are:
227 - "disabled": the port is disabled
228 - "okay": the port is enabled
229 - nvidia,usb2-companion: A single cell that specifies the physical port number
230 to map this super-speed USB port to. The range of valid port numbers varies
232 - 0-2: for Tegra124 and Tegra132
233 - 0-3: for Tegra210
236 - nvidia,internal: A boolean property whose presence determines that a port
237 is internal. In the absence of this property the port is considered to be
240 - maximum-speed: Only for Tegra194. A string property that specifies maximum
241 supported speed of a usb3 port. Valid values are:
242 - "super-speed-plus": default, the usb3 port supports USB 3.1 Gen 2 speed.
243 - "super-speed": the usb3 port supports USB 3.1 Gen 1 speed only.
247 - 3x USB2: usb2-0, usb2-1, usb2-2
248 - 1x ULPI: ulpi-0
249 - 2x HSIC: hsic-0, hsic-1
250 - 2x super-speed USB: usb3-0, usb3-1
253 - 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
254 - 2x HSIC: hsic-0, hsic-1
255 - 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
258 - 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
259 - 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
265 ----------------------
271 compatible = "nvidia,tegra124-xusb-padctl";
273 compatible = "nvidia,tegra132-xusb-padctl",
274 "nvidia,tegra124-xusb-padctl";
277 reset-names = "padctl";
284 usb2-0 {
286 #phy-cells = <0>;
289 usb2-1 {
291 #phy-cells = <0>;
294 usb2-2 {
296 #phy-cells = <0>;
305 ulpi-0 {
307 #phy-cells = <0>;
316 hsic-0 {
318 #phy-cells = <0>;
321 hsic-1 {
323 #phy-cells = <0>;
332 pcie-0 {
334 #phy-cells = <0>;
337 pcie-1 {
339 #phy-cells = <0>;
342 pcie-2 {
344 #phy-cells = <0>;
347 pcie-3 {
349 #phy-cells = <0>;
352 pcie-4 {
354 #phy-cells = <0>;
359 sata {
363 sata-0 {
365 #phy-cells = <0>;
372 usb2-0 {
376 usb2-1 {
380 usb2-2 {
384 ulpi-0 {
388 hsic-0 {
392 hsic-1 {
396 usb3-0 {
400 usb3-1 {
416 usb2-0 {
421 usb2-1 {
426 usb2-2 {
437 pcie-0 {
438 nvidia,function = "usb3-ss";
442 pcie-2 {
447 pcie-4 {
454 sata {
458 sata-0 {
459 nvidia,function = "sata";
468 usb2-0 {
474 usb2-1 {
480 usb2-2 {
484 vbus-supply = <&vdd_usb3_vbus>;
487 usb3-0 {
488 nvidia,port = <2>;
495 ---------
500 compatible = "nvidia,tegra210-xusb-padctl";
503 reset-names = "padctl";
510 clock-names = "trk";
514 usb2-0 {
516 #phy-cells = <0>;
519 usb2-1 {
521 #phy-cells = <0>;
524 usb2-2 {
526 #phy-cells = <0>;
529 usb2-3 {
531 #phy-cells = <0>;
538 clock-names = "trk";
542 hsic-0 {
544 #phy-cells = <0>;
547 hsic-1 {
549 #phy-cells = <0>;
556 clock-names = "pll";
558 reset-names = "phy";
562 pcie-0 {
564 #phy-cells = <0>;
567 pcie-1 {
569 #phy-cells = <0>;
572 pcie-2 {
574 #phy-cells = <0>;
577 pcie-3 {
579 #phy-cells = <0>;
582 pcie-4 {
584 #phy-cells = <0>;
587 pcie-5 {
589 #phy-cells = <0>;
592 pcie-6 {
594 #phy-cells = <0>;
599 sata {
601 clock-names = "pll";
603 reset-names = "phy";
607 sata-0 {
609 #phy-cells = <0>;
616 usb2-0 {
620 usb2-1 {
624 usb2-2 {
628 usb2-3 {
632 hsic-0 {
636 hsic-1 {
640 usb3-0 {
644 usb3-1 {
648 usb3-2 {
652 usb3-3 {
668 usb2-0 {
673 usb2-1 {
678 usb2-2 {
683 usb2-3 {
694 pcie-0 {
695 nvidia,function = "pcie-x1";
699 pcie-1 {
700 nvidia,function = "pcie-x4";
704 pcie-2 {
705 nvidia,function = "pcie-x4";
709 pcie-3 {
710 nvidia,function = "pcie-x4";
714 pcie-4 {
715 nvidia,function = "pcie-x4";
719 pcie-5 {
720 nvidia,function = "usb3-ss";
724 pcie-6 {
725 nvidia,function = "usb3-ss";
731 sata {
735 sata-0 {
736 nvidia,function = "sata";
744 usb2-0 {
749 usb2-1 {
751 vbus-supply = <&vdd_5v0_rtl>;
755 usb2-2 {
757 vbus-supply = <&vdd_usb_vbus>;
761 usb2-3 {
766 usb3-0 {
768 nvidia,lanes = "pcie-6";
769 nvidia,port = <1>;
772 usb3-1 {
774 nvidia,lanes = "pcie-5";
775 nvidia,port = <2>;