Lines Matching +full:0 +full:xcfff
21 1,0: use 1st APIC table
22 default: 0
62 acpi.debug_layer=0x20000000
64 acpi.debug_layer=0x400000
67 acpi.debug_layer=0xffffffff acpi.debug_level=0x2
69 acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
269 behaviour to be specified. Bit 0 enables warnings,
365 bsp: External NMI is delivered only to CPU 0
367 backup of CPU 0
415 Format: <bool> (0 = real, 1 = synthetic (default))
421 Format: { "0" | "1" | "off" | "on" }
422 0 | off - kernel audit is disabled and can not be
433 Format: <int> (must be >=0)
437 behavior is to disable the BAU (i.e. bau=0).
438 Format: { "0" | "1" }
439 0 - Disable the BAU.
466 no delay (0).
511 algorithm. Accepted values range from 0 to 7
550 Format: { "0" | "1" }
552 0 -- check protection applied by kernel (includes
632 memory allocations. A value of 0 disables CMA
639 contiguous memory allocations. A value of 0 disables
641 specificed, the default value is 0.
693 uart[8250],0x<addr>[,options]
727 seconds. A value of 0 disables the blank timer.
728 Defaults to 0.
739 0: default value, disable debugging
802 0: to disable low allocation.
840 Format=<0|1>
843 We default to 0 (no extra messages), setting it to
916 drivers) that have opted in will be ignored. A timeout of 0
1105 uart[8250],0x<addr>[,options]
1221 earlyprintk=serial[,0x...[,baudrate]]
1241 earlyprintk=serial,0x1008,115200
1315 If efi_fake_mem=2G@4G:0x10000,2G@0x10a0000000:0x10000
1316 is specified, EFI_MEMORY_MORE_RELIABLE(0x10000)
1317 attribute is added to range 0x100000000-0x180000000 and
1318 0x10a0000000-0x1120000000.
1320 If efi_fake_mem=8G@9G:0x40000 is specified, the
1321 EFI_MEMORY_SP(0x40000) attribute is added to
1322 range 0x240000000-0x43fffffff.
1362 Format: {"0" | "1"}
1364 0 -- permissive (log only, no denials).
1366 Default value is 0.
1454 in the tracefs tracing directory. default: 0 (no limit)
1506 grcan.enable0= [HW] Configuration of physical interface 0. Determines
1507 the "Enable 0" bit of the configuration register.
1508 Format: 0 | 1
1509 Default: 0
1511 the "Enable 0" bit of the configuration register.
1512 Format: 0 | 1
1513 Default: 0
1515 Format: 0 | 1
1516 Default: 0
1518 Format: <unsigned int> such that (txsize & ~0x1fffc0) == 0.
1521 Format: <unsigned int> such that (rxsize & ~0x1fffc0) == 0.
1531 Format: 0 | 1
1536 Format: 0 | 1 (for off | on)
1599 Format: 0 | 1
1608 terminal devices. Valid values: 0..8
1654 Format: { 1 | Y | y | 0 | N | n }
1656 0, N, n: don't ever reset controller
1680 brightness value of 0 indicates backlight switched off,
1682 to maximum brightness. If this parameter is set to 0
1684 is set to 1, a brightness value of 0 sets the backlight
1688 0 -- machine default
1705 default value is 0x0, which has a special meaning.
1709 of 0x0 enables probing the two first ports as if it
1710 was 0x3.
1781 owned by uid=0.
1802 mode bit set by either the effective uid (euid=0) or
1803 uid=0.
1821 opened for read by uid=0.
1869 Default is 0, 0
1873 Format: 0 | 1
1877 Format: 0 | 1
1881 register contents for all processes. 0x55555554 by
1882 default (disallow access to all but pkey 0). Can
1891 Format: { "0" | "1" }
1892 0 -- basic integrity auditing messages. (Default)
1942 0 disables intel_idle and fall back on acpi_idle.
2007 Format: { "0" | "1" }
2008 0 - Lazy mode.
2020 Format: { "0" | "1" }
2021 0 - Use IOMMU translation for DMA.
2030 0x80
2031 Standard port 0x80 based delay
2032 0xed
2033 Alternate port 0xed based delay (needed on some systems)
2114 <cpu number> begins at 0 and the maximum value is
2155 example, to map HPET-ID decimal 0 to
2157 ivrs_hpet[0]=00:14.0
2162 example, to map UART-HID:UID AMD0020:0 to
2164 ivrs_acpihid[00:14.5]=AMD0020:0
2272 0: force disabled
2276 Default is 0 (don't ignore, but inject #GP)
2283 Default is 0 (off)
2300 back to huge pages. 0 disables the recovery, otherwise if
2325 [KVM,ARM] Trap guest accesses to GICv3 group-0
2366 Default is 0 (disabled)
2470 libata.dma=0 Disable all PATA and SATA DMA
2478 libata.ignore_hpa=0 keep BIOS limits (default)
2496 number of 0 either selects the first device or the
2511 * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
2613 0 (KERN_EMERG) system is unusable
2635 lp=0 [LP] Specify parallel ports to use, e.g,
2637 lp=reset first parallel port). 'lp=0' disables the
2655 CPU). 0 enables autodetection (default). To determine
2687 will bring up during bootup. maxcpus=n : n >= 0 limits
2692 While n=0 is a special case, it is equivalent to "nosmp",
2800 Example: Exclude memory from 0x18690000-0x1869ffff
2801 memmap=64K$0x18690000
2803 memmap=0x10000$0x18690000
2811 The memory region may be marked as e820 type 12 (0xc)
2823 memory_corruption_check=0/1 [X86]
2844 other rate. 0 disables periodic checking.
2848 default : 0 <disable>
2891 Format:[0..2][b][c][t]
2892 Default: "0tb"
2894 0 - The attached screen is the 3.5" TFT
2922 kpti=0 [ARM64]
2924 nobp=0 [S390]
2965 of 0 disables mminit logging and a level of 4 will
3081 1 indicates lock status, 0 indicates unlock status.
3104 Range: 0,7 : spare reg number
3120 0 to disable accounting
3122 Default value is 0.
3187 To turn off this behaviour, set the value to '0'.
3211 The default parameter value of '0' causes the kernel
3218 Setting this to value to 0 causes the kernel to use
3240 Valid num: 0 or 1
3241 0 - turn hardlockup detector in nmi_watchdog off
3501 echo 0 > /proc/sys/kernel/randomize_va_space
3523 and disable the IO APIC. legacy for "maxcpus=0".
3596 omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
3641 timeout > 0: seconds before rebooting
3642 timeout = 0: wait forever
3643 timeout < 0: reboot immediately
3648 bit 0: print all tasks info
3686 connected to, default is 0.
3689 0 for XT, 1 for AT (default is AT).
3692 parport= [HW,PPT] Specify parallel ports. 0 disables.
3693 Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] }
3760 Mechanism 1 (config address in IO port 0xCF8,
3761 data in IO port 0xCFC, both 32-bit).
3763 Mechanism 2 (IO port 0xCF8 is an 8-bit port for
3764 the function, IO port 0xCFA, also 8-bit, sets
3766 through ports 0xC000-0xCFFF).
3810 irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be
3814 pirqaddr=0xAAAAA [X86] Specify the physical address
3983 Format: { 0 | 1 }
4003 Format: { parport<nr> | timid | 0 }
4008 e.g. pmtmr=0x508
4078 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
4089 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
4127 (0 = never).
4132 0 = disabled, 1 = enabled (default).
4242 Specify rcutree.use_softirq=0 to use rcuc kthreads.
4299 RCU_BOOST is not set, valid values are 0-99 and
4562 Test RCU priority boosting? 0=no, 1=maybe, 2=yes.
4703 refscale is built into the kernel and to 0 (leave
4716 them. If <base> is less than 0x10000, the region
4799 0 "airplane mode". All wifi, bluetooth, wimax, gps, fm,
4804 0 The "airplane mode" button does nothing.
4884 Format: integer between 0 and 10
4885 Default is 0.
4982 Format: { "0" | "1" }
4983 0 -- disable. (may be 1 via CONFIG_CMDLINE="skew_tick=1"
4993 Format: { "0" | "1" }
4995 0 -- disable.
5000 Format: { "0" | "1" }
5002 0 -- disable.
5033 more than 32MB of RAM, 0 otherwise.
5045 memory cgroup sub-caches. 1 to enable, 0 to disable.
5085 0: Toshiba Satellite 1800 (GP data pin select)
5098 Format: 0 | 1
5109 Format: 0 | 1
5369 range 0 < portnr < 1024).
5380 The default value is 0 (no limit).
5415 Format: { on | off | y | n | 1 | 0 }
5419 swapaccount=[0|1]
5422 it if 0 is given (See Documentation/admin-guide/cgroup-v1/memory.rst)
5442 sysfs.deprecated=0|1 [KNL]
5500 0: no polling (default)
5575 echo 0 > /proc/sys/kernel/tracepoint_printk
5729 0 = not authorized, 1 = authorized, 2 = authorized
5740 [USB] Set to log all usbfs traffic (default 0 = off).
5747 [USB] Set to cycle leds on hubs (default 0 = off).
5751 scheme (default 0 = off).
5755 usbfs (default = 16, 0 = max = 2047).
5826 Example: quirks=0781:5580:bk,0a5c:5834:gij
5917 vdso=0: disable VDSO mapping
5921 vdso32=0 or vdso32=2: disable 32-bit VDSO
5925 vdso32=0; otherwise, the default is vdso32=1.
5928 alias for vdso32=0.
5930 Try vdso32=0 if you encounter an error that says:
5939 video.brightness_switch_enabled= [0,1]
5943 the allocated input device; If set to 0, video driver
5960 virtio_mmio.device=1K@0x100b0000:48:7
6004 fixed addresses of 0xffffffffff600x00 from legacy
6023 Format: 0xYX, X = foreground, Y = background.
6024 Default: 0x07 = light gray on black.
6027 Format: 0xCCBBAA, where AA, BB, and CC are the same as
6035 ranging from 0-255.
6041 ranging from 0-255.
6047 ranging from 0-255.
6051 Format=<0|1>
6058 Format=<-1|0|1>
6062 overridden by individual drivers. 0 will hide
6065 vt.italic= [VT] Default color for italic text; 0-15.
6068 vt.underline= [VT] Default color for underlined text; 0-15.
6080 threshold is set to twice the value. A value of 0
6087 help debugging. 0 disables workqueue stall