freescale/imx6sabre/readme.txt

5 This file documents the Buildroot support for the Freescale SABRE Board
6 for Smart Devices Based on the i.MX 6 and i.MX 6SoloX Series (SABRESD),
7 as well as the Freescale SABRE Board for Automotive Infotainment.
10 board:
14 the board:
18 introduction to the board:
21 Building with NXP kernel and NXP U-Boot
24 First, configure Buildroot for your SABRE board.
25 For i.MX6Q SABRE SD board:
29 For i.MX6DL SABRE SD board:
33 For i.MX6 SoloX SABRE SD board:
37 For i.MX6Q SABRE Auto board:
41 For i.MX6DL SABRE Auto board:
50   - imx6dl-sabresd.dtb or imx6q-sabresd.dtb or imx6sx-sdb.dtb or
51     imx6q-sabreauto.dtb or imx6dl-sabreauto.dtb
52   - rootfs.ext2
53   - rootfs.tar
54   - u-boot.imx
55   - uImage, or zImage for i.MX6 SoloX
57 Building with mainline kernel and mainline U-Boot
60 Mainline U-Boot uses SPL and can support the three
63 First, configure Buildroot for your mx6sabreauto board
65   make imx6-sabreauto_defconfig
72   - imx6dl-sabresd.dtb, imx6q-sabresd.dtb, imx6q-sabresd.dtb
73   - rootfs.ext2
74   - SPL and u-boot.img
75   - u-boot.imx
76   - zImage
87 directory, ready to be dumped on a microSD card. Launch the following
90   dd if=./output/images/sdcard.img of=/dev/<your-microsd-device>
95 board/freescale/common/imx/genimage.cfg.template.
97 Boot the SABRE board
101 --------------
103 To boot your newly created system on an i.MX6 SABRE SD Board (refer to
105 - insert the SD card in the SD3 slot of the board;
106 - locate the BOOT dip switches (SW6), set dips 2 and 7 to ON, all others to OFF;
107 - connect a Micro USB cable to Debug Port and connect using a terminal emulator
109 - power on the board.
112 --------------------
114 To boot your newly created system on an i.MX6 SoloX SABRE SD Board
116 - insert the SD card in the J4-SD4 socket at the bottom of the board;
117 - Set the SW10, SW11 and SW12 DIP switches at the top of the board in
126     off off ON ON ON off off off
130     off ON off off off off off off
132 - connect a Micro USB cable to the J16 Debug Port at the bottom of the
133   board. This is a dual UART debug port; connect to the first tty using
135 - power on the board with the SW1-PWR switch at the top of the board.
138 ----------
140 To boot your newly created system on a SABRE Auto Board (refer to the SABRE for
142 - insert the SD card in the CPU card SD card socket J14;
143 - Set the S1, S2 and S3 DIP switches and J3 jumper to boot from SD on CPU card.
148     off ON off off ON off off off off off
152     off off ON off
156     off off ON ON
158     J3: 1-2
160 - connect an RS-232 UART cable to CPU card debug port J18 UART DB9 and
162 - power on the board.
169 https://community.freescale.com/docs/DOC-95015
170 https://community.freescale.com/docs/DOC-95017
171 https://community.freescale.com/docs/DOC-99218