Lines Matching +full:0 +full:- +full:inch
2 * acme-acqua.dts - Device Tree file for Acqua A5 Board
11 /dts-v1/;
19 stdout-path = "serial0:115200n8";
20 …s = "mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait consoleblank=0";
24 reg = <0x20000000 0x10000000>;
29 clock-frequency = <32768>;
33 clock-frequency = <12000000>;
41 hlcdc-display-controller {
42 pinctrl-names = "default";
43 pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888_alt>;
44 port@0 {
45 hlcdc_panel_output: endpoint@0 {
46 remote-endpoint = <&panel_input>;
55 pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
57 slot@0 {
58 reg = <0>;
59 bus-width = <4>;
66 pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
68 slot@0 {
69 reg = <0>;
70 bus-width = <4>;
71 cd-gpios = <&pioE 1 GPIO_ACTIVE_LOW>;
76 cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
85 timer0: timer@0 {
86 compatible = "atmel,tcb-timer";
87 reg = <0>;
91 compatible = "atmel,tcb-timer";
97 pinctrl-0 = <&pinctrl_i2c0_pu>;
106 compatible = "atmel,sama5d3-macb", "cdns,at91sam9260-macb", "cdns,macb";
109 phy-mode = "rmii";
110 #address-cells = <1>;
111 #size-cells = <0>;
113 nvmem-cells = <ð0_addr>;
114 nvmem-cell-names = "mac-address";
116 phy0: ethernet-phy@1 {
117 interrupt-parent = <&pioE>;
122 /*ethernet-phy@1 {
123 reg = <0x1>;
130 compatible = "i2c-gpio";
131 gpios = <&pioE 1 0 /* SDA */
132 &pioE 2 0 /* SCK */
134 i2c-gpio,delay-us = <4>; /* ~178 kHz */
135 #address-cells = <1>;
136 #size-cells = <0>;
143 read-only;
144 reg = <0x58>;
145 #address-cells = <1>;
146 #size-cells = <1>;
148 eth0_addr: eth-mac-addr@9A {
149 reg = <0x0 0x06>;
155 pinctrl-names = "default";
156 pinctrl-0 = <&pinctrl_pwm0_pwmh0_0 &pinctrl_pwm0_pwmh1_0>;
165 pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
175 cs-gpios = <&pioC 25 0>;
180 atmel,adc-vref = <3300>;
181 atmel,adc-channels-used = <0xfe>;
182 pinctrl-0 = <
196 dmas = <0>, <0>; /* Do not use DMA for i2c2 */
197 pinctrl-0 = <&pinctrl_i2c2_pu>;
227 <AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
259 /* compatible = "acme,43inch", "simple-panel"; */
260 compatible = "acme,50inch", "simple-panel";
261 /* compatible = "acme,70inch", "simple-panel"; */
265 port@0 {
266 panel_input: endpoint@0 {
267 remote-endpoint = <&hlcdc_panel_output>;
274 compatible = "gpio-leds";
279 default-state = "off";
285 default-state = "off";
291 linux,default-trigger = "heartbeat";
297 linux,default-trigger = "mmc0";
298 default-state = "off";