pxa: palmtreo680 flash programming utility

This adds a userspace linux utility that writes the u-boot image to an mtd
partition on the docg4 nand flash.

A special utility is required to do this bec

pxa: palmtreo680 flash programming utility

This adds a userspace linux utility that writes the u-boot image to an mtd
partition on the docg4 nand flash.

A special utility is required to do this because u-boot is partially loaded by
an initial program loader (IPL) that is permanently programmed to the boot
region of the flash. This IPL expects the image to be written in a unique
format. The characteristics of this format can be summarized as follows:
- Flash blocks to be loaded must have a magic number in the oob bytes of the
first page of the block.
- Each page must be written redundantly in the subsequent page.
- The integrated flash controller's "reliable mode" is used, requiring that
alternate 2k regions (4 pages) are skipped when writing.
For these reasons, a u-boot image can not be written using nandwrite from
mtd-utils.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>

show more ...

powerpc/CoreNet: Allow pbl images to take u-boot images != 512K

Instead of assuming that SYS_TEXT_BASE is 0xFFF80000 calculate the initial
pbl command offset by subtracting the image size from the t

powerpc/CoreNet: Allow pbl images to take u-boot images != 512K

Instead of assuming that SYS_TEXT_BASE is 0xFFF80000 calculate the initial
pbl command offset by subtracting the image size from the top of the
24-bit address range. Also increase the size of the memory buffer to
accommodate a larger output image.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andy Fleming <afleming@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Ri

Merge branch 'master' of git://git.denx.de/u-boot-arm

Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Conflicts:
drivers/serial/Makefile

checkpatch.pl: Add 'printf' to logFunctions

Signed-off-by: Tom Rini <trini@ti.com>

mkimage: Add map_sysmem() and IH_ARCH_DEFAULT to simplfy building

These are not actually used in mkimage itself, but the image code (which
is common with mkimage) does use them. To avoid #ifdefs in

mkimage: Add map_sysmem() and IH_ARCH_DEFAULT to simplfy building

These are not actually used in mkimage itself, but the image code (which
is common with mkimage) does use them. To avoid #ifdefs in the image code
just for mkimage, define dummy version of these here. The compiler will
eliminate the dead code anyway.

A better way to handle this might be to split out more things from common.h
so that mkimage can include them. At present any file that mkimage uses
has to be very careful what headers it includes.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

wandboard: Add Boot Splash image with Wandboard logo

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>

build: Use generic boot logo matching

The boot logo matching is now done in following way:

- use LOGO_BMP if it is set, or
- use $(BOARD).bmp if it exists in tools/logos, or
- use $(VENDOR).bmp

build: Use generic boot logo matching

The boot logo matching is now done in following way:

- use LOGO_BMP if it is set, or
- use $(BOARD).bmp if it exists in tools/logos, or
- use $(VENDOR).bmp if it exists in tools/logos, or
- use denx.bmp otherwise.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Wolfgang Denk <wd@denx.de>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
common/cmd_fpga.c
drivers/usb/host/ohci-at91.c

buildman: Produce a sensible error message when branch is missing

Rather than a backtrace, produce a nice error message when an invalid
branch is provided to buildman.

Signed-off-by: Simon Glass <s

buildman: Produce a sensible error message when branch is missing

Rather than a backtrace, produce a nice error message when an invalid
branch is provided to buildman.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

mkimage: Put FIT loading in function and tidy error handling

The fit_handle_file() function is quite long - split out the part that
loads and checks a FIT into its own function. We will use this
fun

mkimage: Put FIT loading in function and tidy error handling

The fit_handle_file() function is quite long - split out the part that
loads and checks a FIT into its own function. We will use this
function for storing public keys into a destination FDT file.

The error handling is currently a bit repetitive - tidy it.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

image: Rename fit_add_hashes() to fit_add_verification_data()

We intend to add signatures to FITs also, so rename this function so that
it is not specific to hashing. Also rename fit_image_set_hashe

image: Rename fit_add_hashes() to fit_add_verification_data()

We intend to add signatures to FITs also, so rename this function so that
it is not specific to hashing. Also rename fit_image_set_hashes() and
make it static since it is not used outside this file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>

show more ...

image: Convert fit_image_hash_set_value() to static, and rename

This function doesn't need to be exported, and with verification
we want to use it for setting the 'value' property in any node,
so re

image: Convert fit_image_hash_set_value() to static, and rename

This function doesn't need to be exported, and with verification
we want to use it for setting the 'value' property in any node,
so rename it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>

show more ...

image: Split hash node processing into its own function

This function has become quite long and much of the body is indented quite
a bit. Move it into a separate function to make it easier to work w

image: Split hash node processing into its own function

This function has become quite long and much of the body is indented quite
a bit. Move it into a separate function to make it easier to work with.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>

show more ...

image: Move HOSTCC image code to tools/

This code is never compiled into U-Boot, so move it into a separate
file in tools/ to avoid the large #ifdef.

Signed-off-by: Simon Glass <sjg@chromium.org>
R

image: Move HOSTCC image code to tools/

This code is never compiled into U-Boot, so move it into a separate
file in tools/ to avoid the large #ifdef.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>

show more ...

image: Split FIT code into new image-fit.c

The FIT code is about half the size of the >3000-line image.c. Split this
code into its own file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-b

image: Split FIT code into new image-fit.c

The FIT code is about half the size of the >3000-line image.c. Split this
code into its own file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>

show more ...

mkimage: Move ARRAY_SIZE to header file

Move this definition from aisimage.c to mkimage.h so that it is available
more widely.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <m

mkimage: Move ARRAY_SIZE to header file

Move this definition from aisimage.c to mkimage.h so that it is available
more widely.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>

show more ...

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Conflicts:
drivers/mtd/nand/mxc_nand_spl.c
include/configs/m28evk.h

patman: Do not hardcode python path

Patman requires python 2.7.4 to run but it doesn't
need to be placed in /usr/bin/python.
Use env to ensure that the interpreter used is
the first one on environme

patman: Do not hardcode python path

Patman requires python 2.7.4 to run but it doesn't
need to be placed in /usr/bin/python.
Use env to ensure that the interpreter used is
the first one on environment's $PATH on system
with several versions of Python installed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

buildman: Allow conflicting tags to avoid spurious errors

Conflicting tags can prevent buildman from building two series which exist
one after the other in a branch. There is no reason not to allow

buildman: Allow conflicting tags to avoid spurious errors

Conflicting tags can prevent buildman from building two series which exist
one after the other in a branch. There is no reason not to allow this sort
of workflow with buildman, so ignore conflicting tags in buildman.

Change-Id: I2231d04d8684fe0f8fe77f8ea107e5899a3da5e8
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>

show more ...

imx: Align the imximage header and payload to multiples of 4k

The MX53 ROM loads the data from NAND in multiples of pages and
supports maximum page size of 4k. Thus, align the image and header
to 4k

imx: Align the imximage header and payload to multiples of 4k

The MX53 ROM loads the data from NAND in multiples of pages and
supports maximum page size of 4k. Thus, align the image and header
to 4k to be safe from ROM bugs.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>

show more ...

tools: arm: imx: Implement BOOT_OFFSET command for imximage

Implement BOOT_OFFSET command for imximage. This command is parallel
to current BOOT_FROM command, but allows more flexibility in configur

tools: arm: imx: Implement BOOT_OFFSET command for imximage

Implement BOOT_OFFSET command for imximage. This command is parallel
to current BOOT_FROM command, but allows more flexibility in configuring
arbitrary image header offset. Also add an imximage.cfg with default
offset values into arm/arch/imx-common/ so the board-specific imximage.cfg
can include this file to avoid magic constants.

The syntax of BOOT_OFFSET command is "BOOT_OFFSET <u32 offset>".

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefan Roese <sr@denx.de>

show more ...

mxs: mxsboot: Move sdcard BCB header to 4 sectors offset

The MX23 Boot ROM does blindly load from 2048 offset while the MX28
does parse the BCB header to known where to load the image from. We
move

mxs: mxsboot: Move sdcard BCB header to 4 sectors offset

The MX23 Boot ROM does blindly load from 2048 offset while the MX28
does parse the BCB header to known where to load the image from. We
move the BCB header to 4 sectors offset so same code can be used by
both SoCs avoiding code duplication.

This idea was given by Marek Vasut <marex@denx.de>

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Marek Vasut <marex@denx.de>

show more ...

patman: fix gitutil for decorations

The git config parameter log.decorate is quite useful when working with git.
Patman, however can not handle the decorated output when parsing the commit.
To preve

patman: fix gitutil for decorations

The git config parameter log.decorate is quite useful when working with git.
Patman, however can not handle the decorated output when parsing the commit.
To prevent this use the '--no-decorate' switch for git-log.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

fdt: Ensure that libfdt_env.h comes from U-Boot

When building host utilities, we include libfdt.h from the host, not from
U-Boot. This in turn brings in libfdt_env.h from the host, which can mess
up

fdt: Ensure that libfdt_env.h comes from U-Boot

When building host utilities, we include libfdt.h from the host, not from
U-Boot. This in turn brings in libfdt_env.h from the host, which can mess
up the types and cause a build failure, depending on the host environment.
To fix this, force inclusion of U-Boot's libfdt_env.h so that the types
are correct.

Another way to fix this is to use -nostdinc and -idirafter to ensure that
system includes are included after U-Boot ones. Unfortunately this means
that U-Boot's errno.h gets included instead of the system one. This in
turn requires a hack to errno.h to redirect things, so all in all the
solution in this patch is probably cleaner.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...