Merge branch 'u-boot/master' into 'u-boot-arm/master'

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Move default y configs out of arch/board Kconfig

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defc

Move default y configs out of arch/board Kconfig

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-net

Fixup include/configs/unipher.h to not set CONFIG_LIB_RAND

Signed-off-by: Tom Rini <trini@konsulko.com>

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (comm

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

Merge git://git.denx.de/u-boot-nand-flash

mtd: vf610_nfc: enable ONFI detection

This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAN

mtd: vf610_nfc: enable ONFI detection

This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.

Signed-off-by: Stefan Agner <stefan@agner.ch>

show more ...

mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig

This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kin

mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig

This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>

show more ...

arm: vf610: Remove duplicate MTD defines.

Some MTD defines are repeated twice; once with UBI and then with MTD.
Remove the duplicate MTD defines from the UBI grouping.

Signed-off-by: Bill Pringleme

arm: vf610: Remove duplicate MTD defines.

Some MTD defines are repeated twice; once with UBI and then with MTD.
Remove the duplicate MTD defines from the UBI grouping.

Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>

show more ...

arm: vf610: fix boot from SD-card

Boot from SD-card (and probably also from NAND) was broken since
commit d6d07a9bec ("arm: vf610: add NAND support for vf610twr").
It looks like the increased size o

arm: vf610: fix boot from SD-card

Boot from SD-card (and probably also from NAND) was broken since
commit d6d07a9bec ("arm: vf610: add NAND support for vf610twr").
It looks like the increased size of U-Boot lead to a situation
where the boot ROM overwrote its own stack/heap while loading
U-Boot from the SD-card to the SRAM. However, U-Boot worked fine
when loaded through USB serial loader directly into SRAM. It
looks like loading from SD-card uses other stack/heap location
then the serial loader (or maybe no stack or heap at all).
This fix moves U-Boot to gfxRAM, which is 512kB in size and is not
used by the boot ROM nor the SD-card loader of it.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge remote-tracking branch 'u-boot-imx/master'

The single file conflict below is actually trivial.

Conflicts:
board/boundary/nitrogen6x/nitrogen6x.c

arm: vf610: add NAND support for vf610twr

This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional co

arm: vf610: add NAND support for vf610twr

This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).

Signed-off-by: Stefan Agner <stefan@agner.ch>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Conflicts:
boards.cfg

Merge branch 'master' of git://git.denx.de/u-boot-arm

arm: vf610: Add QSPI support for VF610TWR

Add QSPI support for VF610TWR, such as clock and iomux.

Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

vf610twr: Set default environment to use zImage

Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead o

vf610twr: Set default environment to use zImage

Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>

show more ...

config: remove platform CONFIG_SYS_HZ definition part 2/2

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: Add a default CONFIG_SYS_PROMPT

The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this t

config: Add a default CONFIG_SYS_PROMPT

The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-i2c

i2c: update config using mxc driver to new subsystem

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <s

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge branch 'u-boot/master' into u-boot-arm/master