common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINT

common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>

show more ...

Merge branch 'next-sync' of git://git.denx.de/u-boot-arm into next

OMAP3:SDRC: introduce DDR types

Micron DDR timings based on:
http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d401731

OMAP3:SDRC: introduce DDR types

Micron DDR timings based on:
http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d4017316d86;hb=HEAD

Introduce Micron DDR timings and provide
CONFIG_OMAP3_INFINEON_DDR and CONFIG_OMAP3_MICRON_DDR config
options to allow for platform files to setup their timings as
per the type of DDR selected

Reported-by: Steve Sakoman in http://www.nabble.com/forum/Permalink.jtp?root=25779518&post=25959734&page=y

Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:

board/eukrea/cpu9260/cpu9260.c
drivers/serial/serial_s5pc1xx.c
include/asm-arm/arch-s5pc1xx/clock.h
include/asm-arm/arch-s5pc1xx

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:

board/eukrea/cpu9260/cpu9260.c
drivers/serial/serial_s5pc1xx.c
include/asm-arm/arch-s5pc1xx/clock.h
include/asm-arm/arch-s5pc1xx/gpio.h
include/asm-arm/arch-s5pc1xx/pwm.h
include/asm-arm/arch-s5pc1xx/uart.h
include/configs/cpu9260.h
include/configs/cpuat91.h
include/configs/davinci_dm355evm.h
include/linux/mtd/samsung_onenand.h

show more ...

Merge branch 'master' of /home/wd/git/u-boot/custodians

Merge branch 'master-sync' of git://git.denx.de/u-boot-arm

TI: OMAP3: Remove SZ_xx references

This patch removes dependency on the sizes.h header file
and removes all references to SZ_xx.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: Update Overo and Beagle environment

Update default environment to support new kernel DSS2 subsystem and
simplify rootfs type and location changes.

Signed-off-by: Steve Sakoman <sakoman@gmail

OMAP3: Update Overo and Beagle environment

Update default environment to support new kernel DSS2 subsystem and
simplify rootfs type and location changes.

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>

show more ...

TI: OMAP3: Overo Tobi ethernet support

Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.

This also refactors the smc911x driver to allow for detecting when the
chip is

TI: OMAP3: Overo Tobi ethernet support

Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.

This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>

show more ...

TI OMAP3 Use arm init sequence to initialize i2c

This changes fixes an early i2c error.

It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls

TI OMAP3 Use arm init sequence to initialize i2c

This changes fixes an early i2c error.

It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.

While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.

Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.

Run tested on Beagle.
Compile tested on the omap3's

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

TI: OMAP3: Overo Tobi ethernet support

Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.

This also refactors the smc911x driver to allow for detecting when the
chip is

TI: OMAP3: Overo Tobi ethernet support

Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.

This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>

show more ...

TI OMAP3 Use arm init sequence to initialize i2c

This changes fixes an early i2c error.

It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls

TI OMAP3 Use arm init sequence to initialize i2c

This changes fixes an early i2c error.

It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.

While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.

Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.

Run tested on Beagle.
Compile tested on the omap3's

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>

show more ...

omap3: remove typedefs for configuration structs

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>

omap3: embedd gpmc_cs into gpmc config struct

Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.den

omap3: embedd gpmc_cs into gpmc config struct

Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-i2c

OMAP3 Move twl4030 power and led functions

Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.

power_init_r is the only function in board/omap3/common.

OMAP3 Move twl4030 power and led functions

Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.

power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.

The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.

The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED

The directory board/omap3/common was removed because power_init_r
was the only function in it.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>

show more ...

NAND: Part 2: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...

Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF

NAND: Part 2: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...

Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.

This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-arm

OMAP3: Remove legacy NAND defines

Remove remaining legacy NAND defines for Beagle, EVM, Overo and Pandora.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>

OMAP3: Use functions print_cpuinfo() and checkboard()

Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.

These functions reuse content from the ex

OMAP3: Use functions print_cpuinfo() and checkboard()

Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.

These functions reuse content from the existing function
display_board_info() - which has been removed.

Also, updated the existig OMAP3 configurations to
define:
- CONFIG_DISPLAY_CPUINFO
- CONFIG_DISPLAY_BOARDINFO

Signed-off-by: Sanjeev Premi <premi@ti.com>

show more ...

OMAP3: Fix changed mmc init command

In recent U-Boot mmcinit changed to mmc init.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>

Add "source" command; prepare removal of "autoscr" command

According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months

Add "source" command; prepare removal of "autoscr" command

According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.

This patch prepares this change and starts a 6 month transition
period as follows:

- The new "source" command has been added, which implements exactly
the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
have *not* been adapted yet; these will be renamed resp. removed in
a separate patch when the support for the "autoscr" command get's
finally dropped.

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm