driver/i2c/mxc: Enable I2C bus 3 and 4

Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.

Sig

driver/i2c/mxc: Enable I2C bus 3 and 4

Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>

show more ...

Merge branch 'u-boot/master'

Merge branch 'master' of git://git.denx.de/u-boot-imx

imx:mx6slevk support reading temperature

This patch is to support reading temperature for mx6slevk board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

mx6slevk: Use the default CONFIG_SYS_PBSIZE

Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because

mx6slevk: Use the default CONFIG_SYS_PBSIZE

Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".

Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'

imx:mx6slevk add pmic and i2c configuration

Add pmic and i2c configuration in board header file.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

imx: mx6: Change ENV offset to 512K bytes for larger u-boot image

To align with other mx6 boards, change ENV offset from 384KB to
512KB position to fit a larger u-boot image.

Signed-off-by: Ye.Li <

imx: mx6: Change ENV offset to 512K bytes for larger u-boot image

To align with other mx6 boards, change ENV offset from 384KB to
512KB position to fit a larger u-boot image.

Signed-off-by: Ye.Li <B37916@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-spi

imx:mx6slevk add spi nor boot support

Add spi nor boot support for mx6slevk board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.c

imx:mx6slevk add spi nor boot support

Add spi nor boot support for mx6slevk board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-usb

Conflicts:
board/freescale/mx6sxsabresd/mx6sxsabresd.c

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

imx: mx6slevk: Change default mmcdev to USDHC2 device

Since USDHC1 and USDHC3 added, the dev index for USDHC2 changed to
1. So modify the default mmcdev in environment variables to dev 1.

Signed-of

imx: mx6slevk: Change default mmcdev to USDHC2 device

Since USDHC1 and USDHC3 added, the dev index for USDHC2 changed to
1. So modify the default mmcdev in environment variables to dev 1.

Signed-off-by: Ye.Li <B37916@freescale.com>

show more ...

imx:mx6slevk add board level support for usb

Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode

There are two usb port on mx6slevk board:
1. otg port
2. host port
The following

imx:mx6slevk add board level support for usb

Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode

There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

imx: mx6slevk: Add support for USDHC1 and USDHC3 slots

There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environm

imx: mx6slevk: Add support for USDHC1 and USDHC3 slots

There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.

Signed-off-by: Ye.Li <B37916@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge remote-tracking branch 'u-boot-imx/master'

The single file conflict below is actually trivial.

Conflicts:
board/boundary/nitrogen6x/nitrogen6x.c

Merge branch 'uboot'

spi: mxc: fix sf probe when using mxc_spi

MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information

spi: mxc: fix sf probe when using mxc_spi

MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:

cs = (cs | gpio << 8)

This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".

This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.

Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.

Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'