arm: ls102xa: Adjust the load address of U-Boot for NOR boot

The original load address of U-Boot is 0x67f80000. The address
space of NOR flash is 0x60000000 to 0x67ffffff. It will cause
the size of

arm: ls102xa: Adjust the load address of U-Boot for NOR boot

The original load address of U-Boot is 0x67f80000. The address
space of NOR flash is 0x60000000 to 0x67ffffff. It will cause
the size of u-boot couldn't be larger than 512K. As more features
are supported in u-boot, the size of u-boot is larger than 512K.

To fix this issue, the load address of U-Boot for NOR boot is
adjusted to 0x60100000.

In RCW, the PBI command needs to change as follows:
.pbi
-write 0xee0200, 0x67f80000
+write 0xee0200, 0x60100000
.end

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

driver/i2c/mxc: Enable I2C bus 3 and 4

Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.

Sig

driver/i2c/mxc: Enable I2C bus 3 and 4

Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

arm/ls1021a: add PCIe settings

The patch enables and adds PCIe settings for boards LS1021AQDS
and LS1021ATWR.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorks

arm/ls1021a: add PCIe settings

The patch enables and adds PCIe settings for boards LS1021AQDS
and LS1021ATWR.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

arm: ls102xa: Add LPUART support for LS1021ATWR board

This patch adds LPUART support for LS1021ATWR board.
For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console.

Signed-off-by: Alison

arm: ls102xa: Add LPUART support for LS1021ATWR board

This patch adds LPUART support for LS1021ATWR board.
For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

ARM: ls102xa: Setting device's stream id for SMMUs.

LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of t

ARM: ls102xa: Setting device's stream id for SMMUs.

LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

ARM: ls102xa: allow all the peripheral access permission as R/W.

The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves,

ARM: ls102xa: allow all the peripheral access permission as R/W.

The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.

For now we configure all the peripheral access permissions as R/W.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

ls102xa: changing a few targets' configurations.

Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuratio

ls102xa: changing a few targets' configurations.

Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

arm: ls102xa: Add QSPI boot support for LS1021AQDS/TWR board

This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the

arm: ls102xa: Add QSPI boot support for LS1021AQDS/TWR board

This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

arm: ls102xa: Fix SD/NAND/QSPI boot defination error for QE support

The SD/NAND/QSPI boot definations are wrong for QE support, this
patch is to fix this error.

Signed-off-by: Alison Wang <alison.w

arm: ls102xa: Fix SD/NAND/QSPI boot defination error for QE support

The SD/NAND/QSPI boot definations are wrong for QE support, this
patch is to fix this error.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

arm: ls1021a: Add CONFIG_DOS_PARTITION and CONFIG_CMD_FAT support

This patch will fix the bug that the partitions on the SD card could
not be accessed and add the support for the FAT fs.

Signed-off

arm: ls1021a: Add CONFIG_DOS_PARTITION and CONFIG_CMD_FAT support

This patch will fix the bug that the partitions on the SD card could
not be accessed and add the support for the FAT fs.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

arm: ls102xa: Add SD boot support for LS1021ATWR board

This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initi

arm: ls102xa: Add SD boot support for LS1021ATWR board

This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.

Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

arm: ls102xa: Update PCIe dts node status

The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.

Signed-off-by: Minghuan Lian

arm: ls102xa: Update PCIe dts node status

The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

arm: ls102xa: Add SystemID EEPROM support for LS1021ATWR board

SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.

As LS1 is a little-endian processor, getting the vers

arm: ls102xa: Add SystemID EEPROM support for LS1021ATWR board

SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.

As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.

As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

ls102xa: ifc: nor: fix the write issue when bytes unaligned

Add define CONFIG_SYS_WRITE_SWAPPED_DATA.
For LS1021AQDS and LS1021QTWR nor flash write should swap the
bytes when handle unaligned tail b

ls102xa: ifc: nor: fix the write issue when bytes unaligned

Add define CONFIG_SYS_WRITE_SWAPPED_DATA.
For LS1021AQDS and LS1021QTWR nor flash write should swap the
bytes when handle unaligned tail bytes.

Because of the ending, if the date bus width is 16-bits and the
number of bytes is odd, we should swap the byte when write the
last one.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

config: remove redundant CONFIG_SYS_PROMPT defines

Since commit 0defddc851ed (config: Add a default CONFIG_SYS_PROMPT),
each board header does not need to define CONFIG_SYS_PROMPT
as long as it uses

config: remove redundant CONFIG_SYS_PROMPT defines

Since commit 0defddc851ed (config: Add a default CONFIG_SYS_PROMPT),
each board header does not need to define CONFIG_SYS_PROMPT
as long as it uses the default prompt "=> ".

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

show more ...

qe: add qe support for ls1021a-twr board

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

kconfig: move CONFIG_SYS_HZ to lib/Kconfig

CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h
(but some boards still have redundant definitions).

This commit moves the definition and the

kconfig: move CONFIG_SYS_HZ to lib/Kconfig

CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h
(but some boards still have redundant definitions).

This commit moves the definition and the document in README to
Kconfig. Since lib/Kconfig can assure that CONFIG_SYS_HZ is 1000,
the sanity check in lib/time.c should be removed.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Marek Vasut <marex@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq