| #
39446bce |
| 25-Jul-2014 |
Stephen Warren <swarren@nvidia.com> |
ARM: tegra: enable DFU too
Enable DFU protocol support (via the "dfu" command) on Tegra boards where
USB device/gadget mode is enabled.
Note that for DFU to operate correctly on Tegra, we still nee
ARM: tegra: enable DFU too
Enable DFU protocol support (via the "dfu" command) on Tegra boards where
USB device/gadget mode is enabled.
Note that for DFU to operate correctly on Tegra, we still need some DFU
fixes/enhancements that are going through the DFU -> USB trees. However,
the code builds just fine without those changes, and applying this patch
now will allow both sets of patches to meet in the main U-Boot tree much
more quickly.
In order to run test/dfu/dfu_gadget_test.sh, you would need to add the
following to the board configuration:
CONFIG_EXT4_WRITE
CONFIG_CMD_EXT4_WRITE
However, I haven't enabled those here, since I believe the main use-case
for DFU on Tegra is raw flash writing, rather than filesystem access, so
we don't need the additional code-size hit. However, I could be persuaded
otherwise! We should probably add a separate test script for raw flash
access.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|
| #
dab5e346 |
| 16-Jul-2014 |
Stefano Babic <sbabic@denx.de> |
Merge branch 'master' of git://git.denx.de/u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>
Conflicts:
boards.cfg
|
| #
55e8250b |
| 08-Jun-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-arm
|
| #
e6607cff |
| 29-May-2014 |
Stephen Warren <swarren@nvidia.com> |
ARM: tegra: enable USB device mode and UMS on some boards
For each of Jetson TK1, Venice2, and Beaver:
- Enable the first USB controller in DT, and describe its configuration.
- Enable USB device/
ARM: tegra: enable USB device mode and UMS on some boards
For each of Jetson TK1, Venice2, and Beaver:
- Enable the first USB controller in DT, and describe its configuration.
- Enable USB device/gadget support. This allows the user to type e.g.
"ums 0 mmc 0" at the command-line to cause U-Boot to act a USB device
implementing the USB Mass Storage protocol, and expose MMC device 0
that way.
This allows a host PC to mount the Tegra device's MMC, partition it, and
install a filesystem on it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|
| #
4180b3db |
| 14-May-2014 |
Marek Vasut <marex@denx.de> |
Merge remote-tracking branch 'u-boot/master' into test
|
| #
bcb879c0 |
| 09-May-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-arm
|
| #
3deb22a4 |
| 29-Apr-2014 |
Stefano Babic <sbabic@denx.de> |
Merge branch 'master' of git://git.denx.de/u-boot-arm
|
| #
94b972d3 |
| 21-Apr-2014 |
Albert ARIBAUD <albert.u.boot@aribaud.net> |
Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'
|
| #
e04bfdac |
| 25-Mar-2014 |
Stephen Warren <swarren@nvidia.com> |
ARM: tegra: add Jetson TK1 board
Jetson TK1 is an NVIDIA Tegra124 reference board, which shares much of
its design with Venice2.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: To
ARM: tegra: add Jetson TK1 board
Jetson TK1 is an NVIDIA Tegra124 reference board, which shares much of
its design with Venice2.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|