ARM: DRA7XX: Enable Fastboot

- Fastboot is enable by default for DRA7XX
- This is based on following patch modified accordingly
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=b2e04f92

ARM: DRA7XX: Enable Fastboot

- Fastboot is enable by default for DRA7XX
- This is based on following patch modified accordingly
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=b2e04f92b5d91c708b6fd6b79d2266966ac51f4b

Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

include: configs: Enable DWC3 and DFU in DRA7xx

Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by

include: configs: Enable DWC3 and DFU in DRA7xx

Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

show more ...

Merge branch 'u-boot/master'

qspi: dra7x: enable quad mode read for ti-qspi driver

This patch enables QUAD read mode for qspi to improve the
read performace while loading the binaries from qspi.

Signed-off-by: Ravi Babu <ravib

qspi: dra7x: enable quad mode read for ti-qspi driver

This patch enables QUAD read mode for qspi to improve the
read performace while loading the binaries from qspi.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

show more ...

TI: armv7: enable UUID and PART

Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining

TI: armv7: enable UUID and PART

Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining it.

Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ti

ARM: OMAP5: DRA7xx: Enable 8-bit eMMC access on the dra7xx_evm

Tested on a Vayu EVM Rev.E2 with DRA752 ES1.1

Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>

Merge branch 'uboot'

spl: replace CONFIG_SPL_SPI_* with CONFIG_SF_DEFAULT_*

Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the

spl: replace CONFIG_SPL_SPI_* with CONFIG_SF_DEFAULT_*

Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.

Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.

Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Hannes Petermaier <hannes.petermaier@br-automation.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ti

ARM: DRA: Enable VTT regulator

DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used b

ARM: DRA: Enable VTT regulator

DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

board/ti/dra7xx: add support for parallel NOR

This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and

board/ti/dra7xx: add support for parallel NOR

This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.

As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */

Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:

show more ...

board/ti/dra7xx: add support for parallel NAND

This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices,

board/ti/dra7xx: add support for parallel NAND

This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices, so in addition to this patch
following board settings are required for NAND device detection [1]:

SW5.9 (GPMC_WPN) = OFF (logic-1)
SW5.1 (NAND_BOOTn) = ON (logic-0) /* Active-low */
SW5.2 (NOR_BOOTn) = OFF (logic-1)
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations
SW2.1 (SYSBOOT[0]) = ON (logic-1) /* selects NAND Boot */
SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */
SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */
SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */
SW2.5 (SYSBOOT[4]) = ON (logic-1) /* selects NAND Boot */
SW2.6 (SYSBOOT[5]) = ON (logic-1) /* selects NAND Boot */
SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */
SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */

SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */
SW3.5 (SYSBOOT[12])= ON (logic-1) /* device type: Addr/Data Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */

Following changes are required in board.cfg to enable NAND on J6-EVM:

show more ...

Merge remote-tracking branch 'u-boot/master' into test

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

dra7xx_evm: Add QSPI_4 support, qspiboot build target

We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot devic

dra7xx_evm: Add QSPI_4 support, qspiboot build target

We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

show more ...

TI:omap5: Move CONFIG_ENV_SIZE to board config files

The size of the environment depends on the backing store, move this to
the board config files.

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-arm

drivers: net: cpsw: add support to have phy address from cpsw platform data

Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy ad

drivers: net: cpsw: add support to have phy address from cpsw platform data

Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
arch/arm/cpu/armv7/config.mk
board/ti/am43xx/mux.c
include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

dra7xx_evm: Enable GPT commands

Signed-off-by: Tom Rini <trini@ti.com>