Merge branch 'master' of git://git.denx.de/u-boot

am43xx_evm: mmc: do not define DM_MMC for spl

Since spl doesn't support DM currently, do not define DM_MMC
for spl build.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

am43xx_evm.h: : switch to CONFIG_OMAP_SERIAL for non-SPL DM_SERIAL

Tested on am437x gp evm and am437x sk evm

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

Merge remote-tracking branch 'u-boot/master'

am437x_evm: increase phy autoneg timeout

When AM437x EVM is connected to Gigabit switch, it takes
more time to finish auto-negotiation than on a 10/100 switch.

The default 4 second limit times-out

am437x_evm: increase phy autoneg timeout

When AM437x EVM is connected to Gigabit switch, it takes
more time to finish auto-negotiation than on a 10/100 switch.

The default 4 second limit times-out more often than not. This is
observed when testing with a D-Link DGS-1008A desktop switch.

Increase the auto-negotiation time-out for AM437x EVM to handle
this case.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>

show more ...

ti_armv7_common: env: Consolidate MMC args

Define default mmc args in ti_armv7_common.h so that all
TI platforms can reuse.

Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokesh

ti_armv7_common: env: Consolidate MMC args

Define default mmc args in ti_armv7_common.h so that all
TI platforms can reuse.

Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

include: configs: am43xx_evm: add 'usb stop' in usbboot env

The usbboot environment variable has 'usb start' command but
doesn't have the corresponding 'usb stop' command. This breaks
usb peripheral

include: configs: am43xx_evm: add 'usb stop' in usbboot env

The usbboot environment variable has 'usb start' command but
doesn't have the corresponding 'usb stop' command. This breaks
usb peripheral mode if tried after 'run usbboot' fails to load
the images in usb host mode.

Fix it here by adding 'usb stop' command in usbboot env.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

configs: split ti_armv7_common into a omap generic header

TI armv7 based SoCs are based on two architectures - one based on OMAP
generation architecture and others based on Keystone architecture.

M

configs: split ti_armv7_common into a omap generic header

TI armv7 based SoCs are based on two architectures - one based on OMAP
generation architecture and others based on Keystone architecture.

Many of the options are architecture specific, however a lot are common
with v7 architecture. So, step 1 will be to move out OMAP specific stuff
from ti_armv7_common into a ti_armv7_omap.h header which is then used
by all the relevant architecture headers.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

Merge git://git.denx.de/u-boot-usb

usb: USB download gadget and functions config options coherent naming

This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config op

usb: USB download gadget and functions config options coherent naming

This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>

Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)

show more ...

usb: xhci: omap: Remove common dwc3 drv functions calls

Remove all redundant dwc3 driver function calls that
are defined by dwc3 driver

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-spi

defconfig: Move CONFIG_SPI_FLASH_BAR from configs

This commit moves:
- CONFIG_SPI_FLASH_BAR

from include/configs/*.h into configs/*_defconfigs

Signed-off-by: Jagan Teki <jteki@openedev.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Move default y configs out of arch/board Kconfig

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defc

Move default y configs out of arch/board Kconfig

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

am43xx_evm: add eth boot support

add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falco

am43xx_evm: add eth boot support

add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

am43xx_evm: add usb host boot support

While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config ta

am43xx_evm: add usb host boot support

While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

am43xx: Update CONFIG_SPL_TEXT_BASE

With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon).

am43xx: Update CONFIG_SPL_TEXT_BASE

With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon). Prior silicon is OK using this address as well.

Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

show more ...

ARM: AM43x: Fix MAX_RAM_BANK_SIZE

On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BAN

ARM: AM43x: Fix MAX_RAM_BANK_SIZE

On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.

Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

am43xx_evm: Enable NAND boot

Enable booting from NAND on the am437xx-evm.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.c

am43xx_evm: Enable NAND boot

Enable booting from NAND on the am437xx-evm.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

am335x_evm: am44xx_evm: dra7xx_evm: nand: Fix file-system partition name

We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume

am335x_evm: am44xx_evm: dra7xx_evm: nand: Fix file-system partition name

We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"

The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

configs: remove CONFIG_NET_MULTI

CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.

Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@li

configs: remove CONFIG_NET_MULTI

CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.

Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-net

Fixup include/configs/unipher.h to not set CONFIG_LIB_RAND

Signed-off-by: Tom Rini <trini@konsulko.com>