net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (comm

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

ti: am335x/am437x/omap5 devices: Unify network environment variables

Across several devices network environment variables are duplicated.
Move these variables to a common include file which insures

ti: am335x/am437x/omap5 devices: Unify network environment variables

Across several devices network environment variables are duplicated.
Move these variables to a common include file which insures the environment
variables are reused and insures devices across product lines share the same
values.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

include: configs: Enable DWC3 and DFU in AM43xx

Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by

include: configs: Enable DWC3 and DFU in AM43xx

Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ti

board: ti: am43xx: add support for AM43xx Industrial Development Kit

AM43xx Industrial Development Kit is a new board
based on AM437x line of SoCs. Targetted at Industrial
Automation applications, i

board: ti: am43xx: add support for AM43xx Industrial Development Kit

AM43xx Industrial Development Kit is a new board
based on AM437x line of SoCs. Targetted at Industrial
Automation applications, it comes with EtherCAT, motor
control and other goodies.

Thanks to James Doublesin for all the help.

Cc: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

show more ...

TI: armv7: enable UUID and PART

Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining

TI: armv7: enable UUID and PART

Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining it.

Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ti

arm: am43xx: switch over to CONFIG_ENV_IS_IN_FAT

By using CONFIG_ENV_IS_IN_FAT it's far easier
to have a private, minimal environment for e.g.
booting off of network or mounting rootfs on NFS
withou

arm: am43xx: switch over to CONFIG_ENV_IS_IN_FAT

By using CONFIG_ENV_IS_IN_FAT it's far easier
to have a private, minimal environment for e.g.
booting off of network or mounting rootfs on NFS
without having to modify the configuration header.

Signed-off-by: Felipe Balbi <balbi@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ti

board/ti/am43xx: add support for parallel NAND

This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.

am437x-gp-evm: On this board, NAND Flash signals

board/ti/am43xx: add support for parallel NAND

This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.

am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
controlled by:
(a) Statically using Jumper on connecter (J89) present on board.
(a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
SPI2_CS0 == 0: NAND (default)
SPI2_CS0 == 1: eMMC

am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
Thus only one of the two can be used at a time. Selection is controlled by:
(a) Dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)

NAND device (MT29F4G08AB) on these boards has:
- data-width=8bits
- blocksize=256KB
- pagesize=4KB
- oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.

Signed-off-by: Pekon Gupta <pekon@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

tps65218/am43xx_evm: Add power framework support to TPS65218

Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.

Cc: Łukasz Majewski <l.majewski@s

tps65218/am43xx_evm: Add power framework support to TPS65218

Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.

Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Conflicts:
boards.cfg

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

board: ti: am43xx: add support for AM43xx Starter Kit

AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level d

board: ti: am43xx: add support for AM43xx Starter Kit

AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.

Signed-off-by: Felipe Balbi <balbi@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

arm:am43xx: Add TPS65218 support to scale voltages up

This family is supported by the TPS65218 PMIC. Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is

arm:am43xx: Add TPS65218 support to scale voltages up

This family is supported by the TPS65218 PMIC. Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

ARM: AM43xx: Fix mmcboot command in EXTRA_ENV_SETTINGS

loadbootenv expects devtype variable to be set. This is missing in
mmcboot command. With this the following error comes:
U-Boot# run mmcboot
mm

ARM: AM43xx: Fix mmcboot command in EXTRA_ENV_SETTINGS

loadbootenv expects devtype variable to be set. This is missing in
mmcboot command. With this the following error comes:
U-Boot# run mmcboot
mmc0 is current device
SD/MMC found on device 0
** Bad device usb 0 **
** Bad device usb 0 **
Fixing this by setting devtype as mmc.

Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

arm:am33xx: Rework s_init and add board_early_init_f

With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been

arm:am33xx: Rework s_init and add board_early_init_f

With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared. When SPL booting, this is handled by setting gd
to point to SRAM in s_init. However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

am43xx_evm: Add qspiboot target

The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices. As QSPI is bo

am43xx_evm: Add qspiboot target

The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices. As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Merge remote-tracking branch 'u-boot/master' into test