Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Rece

Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE

CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CO

Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE

CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken. Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

powerpc: Cleanup BOOTFLAG_* references

Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the bo

powerpc: Cleanup BOOTFLAG_* references

Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

show more ...

Makefile: move all Power Architecture boards into boards.cfg

Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards

Makefile: move all Power Architecture boards into boards.cfg

Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE

The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven

Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE

The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

Merge branch 'next' of /home/wd/git/u-boot/next

Conflicts:
include/ppc4xx.h

Signed-off-by: Wolfgang Denk <wd@denx.de>

e300: increase CONFIG_SYS_BOOTMAPSZ to allow booting large kernels

Newer Linux kernels can overrun the initial memory window used for
booting with their BSS area. When this happens, they overwrite t

e300: increase CONFIG_SYS_BOOTMAPSZ to allow booting large kernels

Newer Linux kernels can overrun the initial memory window used for
booting with their BSS area. When this happens, they overwrite the FDT
and silently fail to boot.

On e300 CPUs, the Linux kernel uses an initial BAT covering the first
256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase
the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value
allowed by Linux. This will allow very large kernels to boot.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

Remove unused CONFIG_SERIAL_SOFTWARE_FIFO feature

This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used a

Remove unused CONFIG_SERIAL_SOFTWARE_FIFO feature

This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

powerpc: Update configs to properly set FSL_ELBC

Some parts that have an Enhanced Local Bus Controller weren't
setting CONFIG_FSL_ELBC. Fix this so we can use this define
properly going forward (cu

powerpc: Update configs to properly set FSL_ELBC

Some parts that have an Enhanced Local Bus Controller weren't
setting CONFIG_FSL_ELBC. Fix this so we can use this define
properly going forward (currently it's only used if PHYS_64BIT is
set, which meant not all platforms needed to have it set correctly).

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
arch/arm/include/asm/mach-types.h
common/serial.c

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

mpc83xx: turn on icache in core initialization to improve u-boot boot time

before, MPC8349ITX boots u-boot in 4.3sec:

column1 is elapsed time since first message
column2 is elapsed

mpc83xx: turn on icache in core initialization to improve u-boot boot time

before, MPC8349ITX boots u-boot in 4.3sec:

column1 is elapsed time since first message
column2 is elapsed time since previous message
column3 is the message
0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX
0.000 0.000:
0.000 0.000: Reset Status:
0.000 0.000:
0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.032 0.000: Board: Freescale MPC8349E-mITX
0.032 0.000: UPMA: Configured for compact flash
0.032 0.000: I2C: ready
0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
1.516 1.456: FLASH: 16 MB
2.641 1.125: PCI: Bus Dev VenId DevId Class Int
2.652 0.011: 00 10 1095 3114 0180 00
2.652 0.000: PCI: Bus Dev VenId DevId Class Int
2.652 0.000: In: serial
2.652 0.000: Out: serial
2.652 0.000: Err: serial
2.682 0.030: Board revision: 1.0 (PCF8475A)
3.080 0.398: Net: TSEC1: No support for PHY id ffffffff; assuming generic
3.080 0.000: TSEC0, TSEC1
4.300 1.219: IDE: Bus 0: .** Timeout **

after, MPC8349ITX boots u-boot in 3.0sec:

0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX
0.010 0.000:
0.010 0.000: Reset Status:
0.010 0.000:
0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.017 0.000: Board: Freescale MPC8349E-mITX
0.038 0.020: UPMA: Configured for compact flash
0.038 0.000: I2C: ready
0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
0.260 0.222: FLASH: 16 MB
1.390 1.130: PCI: Bus Dev VenId DevId Class Int
1.390 0.000: 00 10 1095 3114 0180 00
1.390 0.000: PCI: Bus Dev VenId DevId Class Int
1.400 0.010: In: serial
1.400 0.000: Out: serial
1.400 0.000: Err: serial
1.400 0.000: Board revision: 1.0 (PCF8475A)
1.832 0.432: Net: TSEC1: No support for PHY id ffffffff; assuming generic
1.832 0.000: TSEC0, TSEC1
3.038 1.205: IDE: Bus 0: .** Timeout **

also tested on these boards (albeit with a less accurate
boottime measurement method):

seconds: before after
8349MDS ~2.6 ~2.2
8360MDS ~2.8 ~2.6
8313RDB ~2.5 ~2.3 #nand boot
837xRDB ~3.1 ~2.3

also tested on an 8323ERDB.

v2: also remove the delayed icache enablement assumption in arch ppc's
board.c, and add a CONFIG_MPC83xx define in the ITX config file for
consistency (even though it was already being defined in 83xx'
config.mk).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

mpc83xx: enable command line autocompletion

because it's convenient.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:

board/davinci/da830evm/da830evm.c
board/edb93xx/sdram_cfg.c
board/esd/otc570/otc570.c
board/netstar/eeprom.c
board/netstar/eepr

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:

board/davinci/da830evm/da830evm.c
board/edb93xx/sdram_cfg.c
board/esd/otc570/otc570.c
board/netstar/eeprom.c
board/netstar/eeprom_start.S
cpu/arm920t/ep93xx/timer.c
include/configs/netstar.h
include/configs/otc570.h

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

mpc83xx: remove hardcoded network addresses from config files

and avoid e.g., two identical boards from causing random networking
conflicts when hooked up to the same network.

Signed-off-by: Kim Ph

mpc83xx: remove hardcoded network addresses from config files

and avoid e.g., two identical boards from causing random networking
conflicts when hooked up to the same network.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:

cpu/arm_cortexa8/s5pc1xx/cache.c
include/asm-arm/arch-s5pc1xx/sys_proto.h
include/sja1000.h

Signed-off-by: Minkyu Kang <mk7.kang

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:

cpu/arm_cortexa8/s5pc1xx/cache.c
include/asm-arm/arch-s5pc1xx/sys_proto.h
include/sja1000.h

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

show more ...

Merge branch 'next' of ../next

common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINT

common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>

show more ...

Merge branch 'arm/master' into arm/next

Conflicts:
board/AtmarkTechno/suzaku/Makefile
board/amcc/acadia/acadia.c
board/amcc/katmai/katmai.c
board/amcc/luan/luan.c
board/amcc/ocotea/ocotea.c
bo

Merge branch 'arm/master' into arm/next

Conflicts:
board/AtmarkTechno/suzaku/Makefile
board/amcc/acadia/acadia.c
board/amcc/katmai/katmai.c
board/amcc/luan/luan.c
board/amcc/ocotea/ocotea.c
board/cm-bf537u/Makefile
board/cray/L1/L1.c
board/csb272/csb272.c
board/csb472/csb472.c
board/eric/eric.c
board/eric/init.S
board/eukrea/cpuat91/Makefile
board/exbitgen/exbitgen.c
board/exbitgen/init.S
board/freescale/mpc8536ds/config.mk
board/g2000/g2000.c
board/jse/sdram.c
board/mpl/mip405/mip405.c
board/mpl/pip405/pip405.c
board/netstal/hcu5/hcu5.c
board/netstal/mcu25/mcu25.c
board/sc3/sc3.c
board/w7o/init.S
board/w7o/w7o.c
common/cmd_reginfo.c
cpu/ppc4xx/40x_spd_sdram.c
cpu/ppc4xx/44x_spd_ddr.c
doc/README.sbc8548
drivers/misc/fsl_law.c
fs/ubifs/ubifs.c
include/asm-ppc/immap_85xx.h

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfields

some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurati

mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfields

some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.

Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.

also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.

also start to use i/o accessors.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

Merge branch 'master' of /home/wd/git/u-boot/custodians

mpc83xx: accommodate larger kernel sizes by default

linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.

Signed-off-by: Kim

mpc83xx: accommodate larger kernel sizes by default

linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...