B4860QDS: Enable mac command support

One of the I2C EEPROM is used to store/save and edit mac
addresses of ports.
this patch add required CONFIG to support the same

Signed-off-by: Shaveta Leekha <s

B4860QDS: Enable mac command support

One of the I2C EEPROM is used to store/save and edit mac
addresses of ports.
this patch add required CONFIG to support the same

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>

show more ...

powerpc/b4860: Updated default hwconfig to enable only cpc2

CPC1 is not being enabled by default as powerpc is supposed to
use only CPC2. Though by editing hwconfig en_cpc option,
CPC1 can also be e

powerpc/b4860: Updated default hwconfig to enable only cpc2

CPC1 is not being enabled by default as powerpc is supposed to
use only CPC2. Though by editing hwconfig en_cpc option,
CPC1 can also be enabled.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

include: remove CONFIG_SPL/CONFIG_TPL definition in config headers

Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig.

Remove the redundant definition in config headers.

Signed-off-by: Masahiro

include: remove CONFIG_SPL/CONFIG_TPL definition in config headers

Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig.

Remove the redundant definition in config headers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

include: define CONFIG_SPL and CONFIG_TPL as 1

We are about to switch to Kconfig in the next commit.
But there are something to get done beforehand.

In Kconfig, include/generated/autoconf.h defines

include: define CONFIG_SPL and CONFIG_TPL as 1

We are about to switch to Kconfig in the next commit.
But there are something to get done beforehand.

In Kconfig, include/generated/autoconf.h defines boolean
CONFIG macros as 1.

CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1.
Otherwise, when switching to Kconfig, the build log
would be sprinkled with warning messages like this:
warning: "CONFIG_SPL" redefined [enabled by default]

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

powerpc/ifc: fix invalid CSn FTIM2.TCH setting

On some platforms, CSn FTIM2.TCH is set to zero which is invalid,
an invalid hold time makes DUT timing variances, whether it works
or not on luck.

Si

powerpc/ifc: fix invalid CSn FTIM2.TCH setting

On some platforms, CSn FTIM2.TCH is set to zero which is invalid,
an invalid hold time makes DUT timing variances, whether it works
or not on luck.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge remote-tracking branch 'u-boot/master'

Conflicts:
boards.cfg

Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatt

Merge remote-tracking branch 'u-boot/master'

Conflicts:
boards.cfg

Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

powerpc/srio-pcie-boot: Adjust addresses for SRIO/PCIE boot

The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.

The upd

powerpc/srio-pcie-boot: Adjust addresses for SRIO/PCIE boot

The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.

The updated addresses are used to configure the SRIO/PCIE
inbound windows for the boot, and they must be aligned
with the window size based on the SRIO/PCIE modules requirement.
So for the 768KB u-boot image, the inbound window cannot be set
with 0xfff40000 base address and 0xc0000 size, it should be
extended to 1MB size and the base address can be aligned with
the size.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

mpc85xx: configs: remove c=ffe from default environment

AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support
for th

mpc85xx: configs: remove c=ffe from default environment

AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support
for the P4080DS board" and just kept on getting duplicated
in subsequently added board config files.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Edward Swarthout <ed.swarthout@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge remote-tracking branch 'u-boot/master' into test

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

powerpc/freescale: Convert selected boards to generic board architecture

This patch converts the following boards to use generic board: MPC8536DS,
MPC8572DS, MPC8641HPCN, p1_p2_rdb_pc, corenet_ds, t

powerpc/freescale: Convert selected boards to generic board architecture

This patch converts the following boards to use generic board: MPC8536DS,
MPC8572DS, MPC8641HPCN, p1_p2_rdb_pc, corenet_ds, t4qds, B4860QDS. It has
been tested on NOR boot on MPC8536DS, MPC8572DS, P1021RDB, P4080DS,
P5020DS, P5040DS, P3041DS, T4240QDS, B4860QDS.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ying Zhang <b40530@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Haijun.Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Shaohui Xie <Shaohui.Xie@freescale.com>

show more ...

board/b4qds: VID support

The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot read

board/b4qds: VID support

The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.

B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.

Reference for this code is taken from t4qds VID implementation.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>

show more ...

Merge branch 'u-boot/master'

Conflicts:
drivers/net/Makefile

(trivial merge)

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

powerpc/mpc85xx:Update MONITOR_LEN for 768KB u-boot size

U-boot binary size has been increased from 512KB to 768KB.

So update CONFIG_SYS_MONITOR_LEN to reflect the same.

Signed-off-by: Prabhakar K

powerpc/mpc85xx:Update MONITOR_LEN for 768KB u-boot size

U-boot binary size has been increased from 512KB to 768KB.

So update CONFIG_SYS_MONITOR_LEN to reflect the same.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

board/b4qds:Add support of 2 stage NAND boot-loader

Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise D

board/b4qds:Add support of 2 stage NAND boot-loader

Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and CONFIG_SYS_QE_FW_ADDR

CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMA

QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and CONFIG_SYS_QE_FW_ADDR

CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm into master

Conflicts:
arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg
arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg

Signed-off-by: Stefano Babic

Merge branch 'master' of git://git.denx.de/u-boot-arm into master

Conflicts:
arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg
arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Trivial merge conflict, needed to manually remove
local_info as per commit 41364f0f.

Conflicts:
board/samsung/common/board.c

freescale: pblimage: refactor CONFIG_SYS_FSL_PBL_{PBI, RCW}

Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI
and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile.

Signed-off-by: Masahiro

freescale: pblimage: refactor CONFIG_SYS_FSL_PBL_{PBI, RCW}

Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI
and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm