serial: Add support for Qualcomm serial port

This driver works in "new" Data Mover UART mode, so
will be compatible with modern Qualcomm chips only.

Signed-off-by: Mateusz Kulikowski <mateusz.kulik

serial: Add support for Qualcomm serial port

This driver works in "new" Data Mover UART mode, so
will be compatible with modern Qualcomm chips only.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

show more ...

ARM: uniphier: support Debug UART

For ARM32 architecture, CONFIG_DEBUG_LL is available for early
low-level debugging (and actually UniPhier 32bit SoCs use it), but
ARM64 architecture does not suppor

ARM: uniphier: support Debug UART

For ARM32 architecture, CONFIG_DEBUG_LL is available for early
low-level debugging (and actually UniPhier 32bit SoCs use it), but
ARM64 architecture does not support it. Instead, CONFIG_DEBUG_UART
is available as an architecture-independent debug facility.

This commit supports it on all the UniPhier SoCs (including the new
ARMv8 SoCs), which is very useful for new SoC bringups.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

serial: dcc: Move driver to DM

Enabling this driver requires some DT changes.
Adding DCC to root or main bus:
dcc: dcc {
compatible = "arm,dcc";
u-boot,dm-pre-reloc;
};

Extend alias list to link

serial: dcc: Move driver to DM

Enabling this driver requires some DT changes.
Adding DCC to root or main bus:
dcc: dcc {
compatible = "arm,dcc";
u-boot,dm-pre-reloc;
};

Extend alias list to link DCC:
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;

Change stdout-path to point to dcc port.
stdout-path = "serial2:115200n8";

Also add support for debug uart to help with early debug.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mips

drivers: serial: add driver for Microchip PIC32 UART controller.

This adds PIC32 UART controller support based on driver model.

Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-b

drivers: serial: add driver for Microchip PIC32 UART controller.

This adds PIC32 UART controller support based on driver model.

Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze

ppc: xilinx-ppc4xx: Port to DM serial

xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.

Signed-off-by: Ri

ppc: xilinx-ppc4xx: Port to DM serial

xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>

show more ...

serial: uartlite: Add uartlite to Kconfig

- Move config option out of board file.
- Remove uartlite address from config file

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thoma

serial: uartlite: Add uartlite to Kconfig

- Move config option out of board file.
- Remove uartlite address from config file

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>

show more ...

serial: uartlite: Add support for debug console

Add support for debug console.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>

Merge git://git.denx.de/u-boot-dm

serial: lpuart: Move CONFIG_FSL_LPUART to Kconfig

LPUART is seen on Freescale VF610 and QorIQ Layerscape devices.
Create a Kconfig option and move it to defconfig for all boards
that have this seria

serial: lpuart: Move CONFIG_FSL_LPUART to Kconfig

LPUART is seen on Freescale VF610 and QorIQ Layerscape devices.
Create a Kconfig option and move it to defconfig for all boards
that have this serial driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

arm: serial: Add Kconfig entries to facilitate usage of the pl01x driver for early debug output

This patch adds Kconfig entries to facilitate usage of pl01x as
a debug UART.

Signed-off-by: Sergey T

arm: serial: Add Kconfig entries to facilitate usage of the pl01x driver for early debug output

This patch adds Kconfig entries to facilitate usage of pl01x as
a debug UART.

Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>

Acked-by: Simon Glass <sjg@chromium.org>

show more ...

Merge git://git.denx.de/u-boot-dm

dm: serial: Allow the UART driver to be dropped from the image

In very very space-constrained devices even the full UART driver is too
large. In this case the debug UART can still be used in some ca

dm: serial: Allow the UART driver to be dropped from the image

In very very space-constrained devices even the full UART driver is too
large. In this case the debug UART can still be used in some cases.

Add options to enable the UART driver in SPL and U-Boot proper. Enable both
options by default.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>

show more ...

Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze

serial: zynq: Fix incorrect reference to s5p driver

Remove this c&p error from s5p driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-

serial: zynq: Fix incorrect reference to s5p driver

Remove this c&p error from s5p driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

ns16550: move CONFIG_SYS_NS16550 to Kconfig

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

ns16550: zap CONFIG_NS16550_SERIAL

Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@g

ns16550: zap CONFIG_NS16550_SERIAL

Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

ns16550: unify serial_rockchip

Unify serial_rockchip, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Ariel D'Al

ns16550: unify serial_rockchip

Unify serial_rockchip, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

ns16550: unify serial_ppc

Unify serial_ppc, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add TODO comment]
Signe

ns16550: unify serial_ppc

Unify serial_ppc, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add TODO comment]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

ns16550: unify serial_x86

Unify serial_x86, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn

ns16550: unify serial_x86

Unify serial_x86, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

ns16550: add generic binding to unify the drivers

Add generic binding to unify ns16550 drivers. There are
several drivers using almost the same code, such as serial_dw,
serial_keystone, serial_omap,

ns16550: add generic binding to unify the drivers

Add generic binding to unify ns16550 drivers. There are
several drivers using almost the same code, such as serial_dw,
serial_keystone, serial_omap, serial_ppc, serial_rockchip,
serial_tegra.c, and serial_x86. But each is platform specific.

The key difference between these drivers is the way to get
input clock frequency. With this unified approach, fixed clock
frequency should be extracted from "clock-frequency" property of
device tree blob. If this property is not available, the macro
CONFIG_SYS_NS16550_CLK will be used. It can be a constant or a
function to get clock, eg, get_serial_clock().

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

debug_uart: restore ns16550 as default

Since commit 220e8021af96 ("nios2: convert altera_jtag_uart to
driver model"), the default debug uart was changed. Most people
use ns16550 UART, so restore it

debug_uart: restore ns16550 as default

Since commit 220e8021af96 ("nios2: convert altera_jtag_uart to
driver model"), the default debug uart was changed. Most people
use ns16550 UART, so restore it as default.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reported-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'series1_v2' of git://git.denx.de/u-boot-sparc

sparc: leon3: Add debug_uart support to LEON3 serial driver.

Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>